Question about Ford Bronco

1 Answer

Hey, i have a 1990 ford bronco. bad tranny, wont start.

Hey, i have a 1990 ford bronco, and currently its transmission is non-op. plus it will not start. battery is dead, but when jumped the starter will engage but not crank. is it that the starter is not getting enough power? or a bad connection? please, i need an answer. thanks.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 107 Answers

You have a dead cell in your battery witch will not turn the starter motor try switching the old batt w/ the jump batt and that mite do it ... i would start there b4 i checked any wires..

Posted on Jul 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hold gas pedal down start car


If this has a carburetor, look at the Power valve that is connected to the throttle lever. It is a small plate in front of the carb with a lever that moves with the throttle. There is a small rubber valve inside which allows gas to flow between chambers.

Another possibility is the fuel pump. After that, a bad Vacuum leak like from a ruptured EGR diaphragm can cause these problems.

Dec 23, 2013 | Ford Bronco Cars & Trucks

1 Answer

1990 Ford Bronco II manual transmission extremely hard to shift will not go into reverse


90 Ford Bronco II: You have to put it in whichever gear you want it in before you start it or it wont shift at all. Then once you are going its extremely hard to shift into the other gears. Reverse is the only gear that sounds like its grinding.

Aug 16, 2013 | 1990 Ford Bronco II

1 Answer

Can i put a 84 bronco 2 tranny mazda type 14 bolt pan in a 88 bronco 2 that originally had a 12 bolt pan both 4wd


well if it is a 1984 tranny it is a toyo koygo tk4 or tk5, which if mounted in the 84 bronco the transmission sets at a tilt, which means that the transmission crossmember bolts into the frame at a angle.. the mazda tranny was used in 88-90 the transmission crossmember sets straight across and bolts on to the frame on each side with one bolt.. with some major fabricating it is possible but to simply change out nope wont fit..

Jan 28, 2011 | 1988 Ford Bronco II

1 Answer

What transmission is in my 1990 bronco 4.9L I6 300 4 speed manual with over drive


you can find out by the bolt pattern on the pan and ther should be a lable on the side of the tranny or it will be stamped in the metal.

Aug 20, 2010 | 1990 Ford Bronco

1 Answer

Transmission fluid leaking back, 1988 Ford Bronco


your output seal on the tranny or input seal on your transfer case is bad. you have to pull your transfer case to tell. this is a pretty straight forward job. block wheels. put transfer case in neutral. drop front and rear drive lines.diconnect transfer case shift linkage. there is a short commponent connecting the trans to the transfer case. the bolt on either end face each other. remove the bolts to the transmission. the transfer case is heavier than it looks, i suggest getting help. pull back on the transfer case until it will drop down. it will pull out a bit because of the trans output shaft. replace what will probibly turn out to be the tranny output shaft seal and reassemble in reverse order.

Nov 06, 2009 | 1988 Ford Bronco II

2 Answers

The auto tranny is not shifting and is reving up way to high!


try shifting it manually from low,let rpms rise,then 2nd,let rpms rise,then to drive and see what happens.It could be bad drive clutches in the transmission but could be a sticky valve body in the transmission,if it does work by shifting manually add 1\2 pint of dot#3 brake fluid to the transmission fluid to assist in cleaning the pistons in the valve body and seals and to help lubricate parts and seals

Apr 25, 2009 | 1990 Ford Bronco

1 Answer

Transmission type


any transmission that is for a straight six engine. doesn't matter what car it comes out of as long as it is hooked to the same engine it will bolt up to yours.

Mar 10, 2009 | 1990 Ford Bronco II

1 Answer

Transmission slips


check the tranny fluid level

Jan 20, 2009 | 1989 Ford Bronco

1 Answer

Bronco tranny wont shift out of first


sounds like you burnt it up. how long did u drive it like that?

Nov 04, 2008 | 1989 Ford Bronco

1 Answer

Broco


bad vacume module on top of tranny or on the side of transfer case

Oct 01, 2008 | 1988 Ford Bronco II

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...