Question about 1996 Isuzu Trooper

2 Answers

How do you remove the steering wheel off of a 96 trooper the ignition is stuck and it needs to be replaced

Posted by on

  • mr_greentee Jul 31, 2009

    thanks for your answer now im having a problem with getting the ignition off can you help me with that

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,124 Answers

You need a wheel puller.. You can get one at a parts store or maybe walmart.. Should be around $10.00

Rate well ;o)

Posted on Jul 22, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 86 Answers

There is a single screw on the back side of the wheel that needs to be removed. This will loosen the center cap which then simply clips off. with that off, using the proper socket tool, remove the nut.

Posted on Jul 22, 2009

  • Travis
    Travis Jul 31, 2009

    sorry, can't help you you further about the ignition.

    found the solution to the steering wheel here
    http://wiki.answers.com/Q/Is_it_possible...


×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 97 trooper stearing wheel locked up on me while driving cant get it to unlock. How can i go about getting it to?


remove upper and lower steering column covers.
Unplug ignition switch and remove ignition barrel bolts
should have access to steering lock to remove it

Apr 29, 2016 | Cars & Trucks

2 Answers

Anti theft shorted out.


You should look for the alarm fuse and relay and replace them.
Is it the factory alarm or what brand?

Jul 19, 2008 | 1996 Isuzu Trooper

1 Answer

Replace ignition switch


REMOVE THE PLASTIC COVERING FROM THE STEERING COLUMN UNDER THE STEERING WHEEL. YOU PROBABLY WON'T HAVE TO REMOVE THE WHEEL. THERE SHOULD BE SCREWS ON THE BOTTOM SIDE OF THE PLASTIC PIECES . THE SCREWS THAT HOLD THE IGNITION LOCK CYLINDER IN PLACE MAY HAVE SECURITY HEADS, [ROUND , NO SLOTS OR HEXES] YOU WILL NEED A SMALL CHISEL & A SMALL HAMMER TO START THEM TURNING.

IF YOU ONLY WANT TO REPLACE THE ELECTRICAL PART, " THE BLACK PLASTIC WITH THE WIRES " ALL YOU HAVE TO DO IS REMOVE THE SINGLE SCREW FROM THE OPPOSITE END WHERE THE KEYS GO & PULL OUT THE PLASTIC SWITCH.

Jan 09, 2011 | 1993 Isuzu Trooper

1 Answer

Key stuck in ignition -- cannot turn on or off. Can an ignition switch cause the tumbler to lock up? Or does the ignition tumbler need to be replaced? If the ignition tumbler needs to be replaced, how...


lets start simple.get a can of silacone spray oil and spray into the switch and keep moving key and you will find this will reliese the key,if you need to remove the ign switch dont panic as its a simple enough job.Forget about steering wheel and whatever,simply remove the outer plastic cover then this exposes the switch at the back of switch is a plug with wires pull it away ,then below the key you should see a tiny screw undo, and make sure the steering lock is not under pressure,ie steering wheel free,when trying to remove switch move steering wheel back/forward and switch should pull out.good luck.adrian,,,,

Nov 25, 2010 | 1988 Chevrolet Celebrity

2 Answers

I drive a 1997 isuzu trooper, and the steering wheel locked, how do i go about unlocking it?


you need the ignition key to unlock it, if it doesn't work with the key you may need a new key.

Apr 24, 2010 | 1997 Isuzu Trooper

2 Answers

1996 isuzu trooper steering wheel won't unlock


Firstly, if your steering wheel will rotate about an inch, while in the locked position, do the following:

1) swing the wheel as far as it goes, then hold it tightly in position (it may want to return back to position, butdon't let it go!)

2) insert key into ignition, and turn key to "ON", not start.

3) see if steering wheel will now release...


Please advise if this works...

If no, then need to go to next step...

Await your response....

Scott

Nov 12, 2009 | 1996 Isuzu Trooper

1 Answer

96 Cavailer ignition cylinder problem


To remove the ignition lock:
CAUTION
You must remove the steering wheel when replacing the ignition lock. On vehicles with a Supplemental Inflatable Restraint (SIR) system, you must temporarily disable the SIR system and remove the inflator module when removing the steering wheel. Leaving the SIR system on could result in deployment of the air bag and possible personal injury.
  • Disconnect the negative battery cable, and remove the steering wheel.
  • Remove the bumper and the carrier snapring retainer from the steering shaft.
  • Use a lock plate compressor screw tool to install the lock plate compressor screw in the upper steering shaft. To keep the shaft from telescoping, tighten it to 40 inch lbs.
  • Using the lock plate compressor tool, install on the upper steering shaft, tighten it to depress the shaft lock. Remove the shaft lock retainer, the compressor tool and the steering shaft lock.
  • Remove the turn signal canceling cam assembly. Put the turn signal switch in the "N" position and remove the upper bearing spring.
  • Position the turn signal switch so the mounting screws can be removed through the holes in the switch and remove the turn signal lever.
  • Remove the turn signal switch-to-steering column screws and lift the turn signal switch. Remove the wire protector and disconnect the turn signal switch connector.
  • Use a terminal remover tool to disconnect the buzzer switch wires from the turn signal switch connector. Remove the buzzer switch assembly with needle-nose pliers.
  • Place the lock cylinder in the ACC position, then remove the lock retaining screw and the lock cylinder set.
  • To install the new cylinder lock, reverse the removal procedures.
  • Tighten the lock retaining screw to 22 inch lbs., the turn signal switch screws to 59 inch lbs. and turn the turn signal lever screw to 53 inch lbs.
  • As part of the final replacement procedures, check the operation of the switches and the steering column.
f42-11.gif The steering wheel is splined to the steering column and held in place by a nut. Courtesy of General Motors Corporation - Service Operations. gl
G

Jun 24, 2009 | 1996 Chevrolet Cavalier

1 Answer

Replacing the ignition switch in a 96 ford mustang cobra svt


Follow these steps carefully. this will help you achieve this replacement.



  1. Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing them.

  2. Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft.

  3. Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column.

  4. Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out.

  5. Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder.

  6. Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.

Jun 17, 2009 | 1996 Ford Mustang

2 Answers

How do i replace the key cylinder ignition on the 1991 sunbird le


This (plate) is held in place with a snap ring.You will need a special press to remove it and also a steering wheel puller to access the ignition lock cylinder.The actual switch is located on top of the steering column above the brake pedal. It is actuated with a rod from the ignition lock cylinder.

Jan 10, 2009 | 1991 Pontiac Sunbird

Not finding what you are looking for?
1996 Isuzu Trooper Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...