Question about 1992 GMC Jimmy

1 Answer

1992 4x4 4.3 motor 5 speed. What tool do i need... to remove lines from clutch master cyl.

Posted by on

  • 2 more comments 
  • rrrjeep861 Jul 22, 2009

    I will try it, no one around here sells a special tool kit. Do I need to bleed lines after installing new cyl.

  • rrrjeep861 Jul 22, 2009

    I don,t see a bleeder screw like you see on a brake cyl. Do I do it through the reservoir by removing the cap...

  • yadayada
    yadayada May 11, 2010

    u need to bleed the lines, good luck on that.

  • yadayada
    yadayada May 11, 2010

    contact the dealer to order the special tool kit

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,201 Answers

If it is anything like my 93, there is a small role pin at the bottom holding the line on. Get a thin nail or punch and just tap the pin out, be careful not to loose it, cause you need to reuse it.

Posted on Jul 22, 2009

  • 1 more comment 
  • Richard Delahant Jul 22, 2009

    yes you need to bleed the line.

  • Richard Delahant Jul 22, 2009

    The slave valve where the other end of the pipe connects to, has the same set up a role pin.

  • Richard Delahant Jul 24, 2009

    There should be a bleeder screw on the slave valve

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 ford focus 2.0liter. clutch pedaL GOES TO FLOOR. brake master full of fluid.I clutch master or clutch slave cylinder bad?


a plastic master cyl !

master cyl is bypassing internally

slave cylinder is inside the gearbox bell housing
if its leaking .....gearbox out




26351104-h2ljceqgvzc5xcxajl4olrsz-4-0.jpg

26351104-h2ljceqgvzc5xcxajl4olrsz-4-1.jpeg

26351104-h2ljceqgvzc5xcxajl4olrsz-4-3.jpg

Nov 11, 2016 | 2004 Ford Focus

1 Answer

I just purchased a 2007 B4000 5 speed stick and I can feel a constant vibration (not a rhythmic one) through the shifter, gas pedal (I can feel it constantly through the sole of my shoe), and clutch pedal,...


could be a broken engine / trans mount unfortunately a common finding nowadays
if your familiar with tools use a large wrench on a large bolt located someplace on front of SHUT off engine gently but with force attempt to move engine North/east/south/west if it moves any direction more than 1/4 inch in respect to car body (not ground) yep you got a broken one

ooh also ck clutch master cyl fluid level (not brake master cyl) for correct level if low u got a leaky slave cyl

Oct 20, 2013 | Mazda B4000 Cars & Trucks

2 Answers

5 speed Jeep Liberty clutch barely engages when vehicle first start.


If your clutch is hydraulic uses a master cyl. and a slave cyl. It sounds like the slave cyl. but could be both.

Aug 24, 2012 | 2002 Jeep Liberty

1 Answer

No clutch pressure on a hydraulic clutch system borg warner transmission 4 cyl. 5 speed


look for leak....under the dash on the floor if its wet there its the master. Just follow rod from clutch peddle to master. Check the line and not sure if your slave is on the outside of the trans look there or if its in the trans see if its wet coming out of the bell housing (where trans meets engine) and replace that part and bleed system

Mar 01, 2011 | 1995 Isuzu Rodeo

1 Answer

I have a 98 s-1 p/u with a 4 cyl and a 5 speed trans. I pulled the engine and I'm putting a reman 4 cyl back in. When I pulled the engine the clutch slave clyinder spring and bearing feel out. I need to...


You will need the Ford tool designed especially for those fittings.
Most parts stores carry these in the Help section or in the miscellaneous tools area. They usually come as a complete set for all hose and fitting sizes

Aug 04, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

Master cylinder replacement


it is the same deal as brakes it is easy to do and the same things you need to cange master cylinder for the brakes is the same for this little project tools and all the master cylinder for the clutch is smaller then brakes master cylinder and only has one line going out so its a small task

Apr 04, 2010 | 1984 Porsche 944

1 Answer

Press clutch down truck still moves foward on a 98 isuzu hombre


If you've not done anything to your truck, check the Clutch master cylinder under the hood, there is a resivoir that should have brake fluid in it. It usually sits next to the Brake master cylinder & is a smaller unit. If nothing has been done to the system recently, and your fluid is full, either the Clutch Master Cyl. or the Clutch Slave Cy. mounted on the bellhousing of the trans. is defective, or has a leaking connection.

If leaking connection, tighten & bleed the system. Check under the clutch pedal on the floorboard for brake fluid, if you find it, the Clutch Master Cyl is the problem & will need ot be replaced. Otherwise, the Clutch Slave Cyl. will need to be replaced. System has to be bled after replacing either & the Clutch Master Cyl. must be bled before hooking up the lines to the Clutch Slave Cyl.

Good Luck

good luck.

Feb 13, 2010 | 1998 Isuzu Hombre

2 Answers

92 explorer 5 speed clutch master cly is it in the bell housing how long to replace


the master cyl is at the pedal and the slave cyl is the one at the clutch operating end this can be either internal or external of the clutch casing so if you have a problem with clutch operation ?and not sure which/or what is fault ? why not give symptoms ? so we can advise you b4 you spend ?

Jan 12, 2010 | 1992 Ford Explorer

1 Answer

Cant disconnect pushrod from clutch pedal to


have some push all the way down on the clutch than squeeze the plastic tabs on bushing to release u also need a special tool to remove disconnect the hydraulic line from clutch release cylinder most auto stores carry it or let u use /loan for free

Oct 31, 2009 | 2000 Chevrolet Silverado 1500

Not finding what you are looking for?
1992 GMC Jimmy Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...