Where is EVAP purge flow solienod. On2012chevy cruze

This DTC checks for undesired intake vacuum flow to the EVAP system. The control module seals the EVAP system by commanding the EVAP canister purge solenoid valve OFF and the EVAP canister vent solenoid valve ON. The control module monitors the fuel tank pressure (FTP) sensor to determine if a vacuum is being drawn on the EVAP system

Read more at: https://www.obd-codes.com/p0496
Copyright OBD-Codes.com
P0496 EVAP Flow During Non Purge Condition

Follow the code for an explanation of this fault code. P0496 EVAP Flow During Non Purge Condition

Try a new gas cap, that is usually the culprit. Around $20 on up for keyed at any part store. And easy to put on.

getting code p441 could be caused by evap purge solenoid vacuum line loose leaking or restricted, evap purge solenoid faulty, evap purge vacuum line to canister leaking or disconnected,evap canister failed.

Two choice dudes code there...

DTC P0441 - Evaporative Emission (EVAP) Control System Incorrect Purge Flow
EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.
With a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

• Common Chrysler fix - Replace Leak Detection Pump / LDP
• Repair damaged EVAP lines or canister
• Repair open or short in voltage feed circuit to Purge Solenoid
• Repair open in PCM purge command circuit
• Replace purge Solenoid
• Replace vacuum switch
• Repair restriction in Evap line or canister or soleniod
• Repair resistance in purge connector
• Replace PCM

DTC P1441 - Evaporative Emission (EVAP) System Flow During Non-Purge.
Most generally caused by a purge valve stuck open. the only way to diag for sure is with a gm tech 2 scan tool and a smoke machine. but if dont mind spending a few bucks as a good quess. Replace the purge valve.


Hope this helps.

CODE P1441 -- EVAP SYSTEM FLOW DURING NON PURGE CONDITIONS. POSSIBLE CAUSES. EVAP PURGE VALVE PIPE OR THE CHARCOAL CANISTER HAS A TEMPORARY BLOCKAGE. FTP SENSOR IS OUT OF CALIBRATION DAMAGED OR IT IS SKEWED. EVAP PURGE SOLENOID VALVE IS DAMAGED OR HAS FAILED. PCM HAS FAILED.

code p 0441 refers to evaporative emission (EVAP) system --incorrect flow detected ==== causes --- hose connection/s--- intake leak---EVAP canister purge valve replace the purge valve

P1443 Evaporative Emission Control System Control Valve The Evaporative Emission Control System monitors the fuel vapor flow between the engine intake manifold and the EVAP canister. The system failure occurs when a leak or blockage between the intake manifold, the EVAP canister purge valve and the EVAP canister is detected by the PCM.

Code P1443 Possible Causes:

- Pinched, blocked or plugged fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister

- Disconnected, cracked or cut fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister purge valve

P1447 - Evaporative Emission (EVAP) Control System, Purge Flow Monitor
In this evaporative emission (EVAP) control system, purge flow occurs during non-closed throttle conditions. Purge volume is related to air intake volume. Under normal purge conditions (non-closed throttle), the EVAP canister purge volume control solenoid valve is open to admit purge flow. Purge flow exposes the EVAP control system pressure sensor to intake manifold vacuum.

Under normal conditions (non-closed throttle), sensor output voltage indicates if pressure drop and purge flow are adequate. If not, a fault is determined. Malfunction is detected when EVAP control system does not operate properly, EVAP control system has a leak between intake manifold and EVAP control system pressure sensor.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes
* EVAP canister purge volume control solenoid valve stuck closed
* EVAP control system pressure sensor and the circuit
* Loose, disconnected or improper connection of rubber tube
* Blocked rubber tube
* Cracked EVAP canister
* EVAP canister purge volume control solenoid valve circuit
* Closed throttle position switch
* Blocked purge port
* Closed throttle position switch


Test is and send us your updated.

Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Evaporative Emission (EVAP) Canister Purge Regulator Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Purge Solenoid Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Sealing faulty.
Pipes between Tank Breathing and Throttle Body leaky/blocked.
Hose connection(s).
Intake leak.
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve.
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.
VSV connector near air filter box disconnected.