Question about 1989 Jeep Cherokee

1 Answer

Can't get the engine to idel revs all the time will not idel correctly

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,559 Answers

Check the EGR valve and replace if needed and also check the Throttle position sensor

Posted on Jul 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 toyota pickup v6 starts-up step on gas pedel motor then dies


does thr engine rev upwhen started than idels back down.try idel control switch and map sensor

Oct 27, 2012 | Cars & Trucks

1 Answer

High revs


Throttle position sensor.
No check engine light is usually the give-away.

Jul 12, 2012 | 2008 Toyota Corolla

1 Answer

Idels fine when driving it sometimes loses power and stalls if you rev the idel above 3000rpm it stops and runs fine till you stop or slow down the idel below 3000 rpm it shutters and...


If you don't have a check engine light, Start with the air and fuel filter, work your way up to a tune up. Clean the throttle body as best you can on the inside, behind the throttle plate/s

Feb 24, 2011 | Honda Accord Cars & Trucks

1 Answer

I have a 2kd-ftv motor in a toyota hiace van, it starts and runs for 3-4 seconds getting lower and lower in revs till it stalls , sometimes it doesnt stall and picks up after same amount of time and idels...


Hi, you need to firstly replace the fuel filter, the problem is the idle solenoid in the pump has dirt in the piston! From the passenger side of the engine remove the solenoid at the back of the fuel pump 2x 5mm Alan bolts, there is 2 solenoids in the pump the one closest to the block is fuel temp. After the idle solenoid is removed, in the solenoid is a piston held in place by a circlip and there is also a spring in there, clean out all dirt inside and reassemble replace both o'rings and reinstall your problem will be solved. I have just fixed one 2 days ago.

Oct 31, 2010 | 2005 Toyota Tacoma

1 Answer

EPC light came on and engine will not rev higher


i lose power with EPC and brake linning warning lights, after break pad service

May 09, 2010 | 2006 Volkswagen Golf

1 Answer

I have a 1987 toyota camry, at times the steering


check the motor mounts/transmission mounts for excessive wear. Open the hood and with the emergency brake on and the rear wheels blocked with bricks (front and back of the rear tires) have a friend stand to the side and a few feet back of the engine. The other person gets in the car, starts it and with your left foot applied constantly to the brake pedal, use the right foot to rev the motor up and down in drive, then in reverse. You are looking for the engine to show movement front to back or side to side excessively. The engine will stay virtually still during this test if the mounts are good but it sounds like on ore more may be bad.

May 06, 2010 | Toyota Camry Cars & Trucks

1 Answer

The idel revs to 3000 rpms and holds there


there is a problem then because that is not suspose to happen call a tow truck and call your company

Mar 02, 2010 | 1987 Ford Bronco

1 Answer

Will start and run if I rev the engine but will not hold idel.


It could be the throttle body gasket. The gasket gets old and hard and will leak between the throttle body and intake manifold. Also check for vacuum lines that are broken or split.

Feb 24, 2010 | 1991 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...