Question about 2005 Mazda RX-8

1 Answer

Rear brake piston does it need a special tool cuz of e-brake

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 168 Answers

Yes

Posted on Jul 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW DO I CHANGE THE BRAKES REAR ON 2008 TAURUS. I


Hi, if you are replacing the rear pads, you will need a special caliper tool(can be purchased or rented from Autozone or Discount Auto Parts) to reseat the piston as it has to be turned or rotated inward to reseat..
ameezle_2.png


To move the piston back into the caliper, the LH piston is turned clockwise and the RH piston is turned counterclockwise. NOTE: A moderate to heavy force toward the caliper piston must be applied. If sufficient force is not applied, the internal park brake mechanism clutch cone will not engage and the piston will not compress. Using the special tool (or equivalent such as OTC tool 7317A), compress the brake caliper piston into its cylinder.



In an emergency, you can use needle nose pliers, but be careful not to pinch the rubber boot or seal as this will create a leak of brake fluid....
ameezle_3.png

Jun 23, 2011 | 2008 Ford Taurus X

1 Answer

Steps to replacing rear brake pads


A special tool is required to compress the caliper piston on the rear brakes-don't use a C-clamp on the piston.
Raise the vehicle and remove the tire. The rear calipers have only one guide pin. Remove this pin and raise the caliper. Remove the old brake pads. Using the special tool compress the caliper piston-the piston will have one or two slots on it. These slots must in the correct position to remount the caliper. Install the new brake pads and slide the caliper back over the rotor and replace the guide pin. If the caliper doesn't slide over the rotor you'll need to reset the slots on the piston. Replace the tires and you're ready to go.

Jan 01, 2011 | 2000 Buick LeSabre

1 Answer

Need to replace the front & rear brakes . Is there any special tools needed to do this job .


For caliper brakes, mainly a large C-clamp or brake cylinder piston tool, to collapes the piston back into the caliper, to install the new pads. If you have rear drum brakes, they make a couple different brake spring tools for removing the springs on the brake shoes.

Nov 07, 2010 | 1994 Chevrolet Cavalier

3 Answers

Compressing the rear disc brake caliper on 2008 grand caravan


The rear calipers on these models require a special tool that compresses and turns the piston in at the same time -- most parts stores carry this tool.

It is called a caliper piston press -- and it installs where the pads would go and acts like a c-clamp,when turning handle it will turn the caliper piston backinto the caliper as it compresses it.
Anytime the brake rotor or brake pads are being replaced, the rear caliper piston must be seated (bottomed) to compensate for the new brake rotor or lining. Because the Parking Brake self-adjuster mechanism is attached to the piston, a special seating method is required. The only acceptable method is by rotating the piston back into the bore using Retractor,MILLER Special Tool 8807, . Any other seating method will damage the self-adjuster mechanism.
Good luck and hope this helps.

Mar 07, 2010 | Dodge Caravan Cars & Trucks

2 Answers

Changed frt and rear brake rotors and pads. Need to know how to compress the rear caliper piston with built in park brake


The piston must be rotated as it is pushed into the caliper. There is a special tool for this that is sold at just about all parts houses. The tool looks like a small square with various pins for various applications that goes on the end of your 3/8 drive ratchet.

Feb 02, 2010 | 2009 Dodge Journey

4 Answers

1996 olds aurora back brake pad replacement, how to compress the pads to get the caliper back over the pads?


Special tool is a 1" cube with tabs on each side that fits into indentations on the brake piston and can be purchased for $10-12 @ most discount parts stores. Use 3/8" ratchet with short extension and 'special tool to carefully turn piston onto internal hand brake screw. Take care to not tear dust boot. When piston is fully collapsed, make sure to align piston indentations perpendicular to brake pad as there are bumps on pad that fit into them. Also while screwing in piston either remove about 2/3 of brake fluid in master cylinder and refil afterwords or open the bleeder valve on brake piston assembly. Bleed if necessary.

Jul 18, 2009 | 1996 Oldsmobile Cutlass Supreme Coupe

2 Answers

Brake Pad Replacement,2004 VW Touareg,V6 instructions


yes, you need a piston retract tool for the rear cylinders. rear piston must turn clockwise as it is being retracting.

Jun 11, 2009 | 2004 Volkswagen Touareg

2 Answers

Successfully changed front brakes but when i went to change rear brakes the caliper seems to be stuck.what can i do?


your rear brake has most likely a drum in hat style brake.

The caliper is not stuck, you need a special tool to rotate the piston of the brake caliper and depress it down. It is connected to your parking brake, that is why this security measure was taken.

the special tool looks like this :

9d6f12d.gif

a ratchet fits in the center hole and depending on the style of piston you have you will need a specific side of this "cube" tool.
you may need to slide the pads out to see the piston.

I hope this helps, Goodluck!

May 11, 2009 | 2000 Lincoln Continental

4 Answers

Replace rear brake pads on a 2000 grand marquis


rate as fixya if this is what you need. Thanks

  1. Remove the rear disc brake caliper (2K327).
  2. Remove the brake caliper bolts.
  3. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2B582).
  1. sya~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pads.
    Remove the brake pads by pushing inward and rotating the pad up.
  1. NOTE: Use a block of wood or used pad to protect the piston and boots.
    Retract the caliper piston (2196) into the rear disc brake caliper.
cf7b02c.gif

Mar 15, 2009 | 2000 Mercury Grand Marquis

1 Answer

How do you compress rear brake caliper?


Dear Sir/madam,

The pistons on the rear brake calipers SCREW in to the caliper. There are notches on the inner edge of the piston face. engage the notches with a large needle nose plier or a large flat washer and turn clockwise (as you face the piston) to turn the piston in.
There is a special tool that is available at your local autoparts store that is absolutely necessary and will save you a ton of time and aggravation. Using a needle nose plier or washer does not allow you to apply enough pressure unless your are the incredible hulk.

thanks
Good luck

Oct 24, 2008 | 1999 Buick Park Avenue

Not finding what you are looking for?
2005 Mazda RX-8 Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...