Question about 2001 Dodge Durango

1 Answer

4wd service light on, selector swicth does not work or light up

4wd service light just came on after a year of the 4wd not working. Haven't had a chance to check it out until now. Checked fuses selector switch doesn't light up or engages. It seemed that it stopped working after I had the blower resistor changed. The blower was only working on high. So, I had 2 resistors blow out. After I had that changed is when I noticed that the 4wd didn't work anymore. Please, give me info on how to resolve my issue. I know how to do most things in the truck, Just need a starting point. or Information ona how to. Thanks for time

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Same problem , anything???? debiangnu at sbcglobal dot net

Posted on Oct 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4 wheel will not work. the selector switch will show it is in but front tires will not engage No messages on control center


Search Results

    4WD Transfer Case Position Sensor/Selector ... - RepairPal

    repairpal.com > Problems > Chevrolet > Tahoe
    Service 4WD Message May be Displayed on Chevrolet Tahoe. The 4WD transfer .... I had a similar problem with 4 wheel drive selector switch. When I select 4 ...

    4WD Transfer Case Position Sensor/Selector ... - RepairPal

    repairpal.com > Problems > Chevrolet > Suburban 1500
    Service 4WD Message May be Displayed on Chevrolet Suburban 1500 ... When in 4 wheel , it will not in engage sometimes and message comes on to service 4 wheeldrive. ... I replaced the 4wd transfer switch in 2007 and now again it is not working, this would be the ... 2008 Chevrolet Suburban 1500- 4WD156,000Visitor.

    Chevrolet Tahoe Repair: Problems, Cost and Maintenance

    repairpal.com > Cars > Chevrolet
    Having problems with your Chevrolet Tahoe? Learn about common Chevrolet Tahoe problems, recalls and typical maintenance and repair costs. ... ABS Front WheelSpeed Sensors May Fail. Chevrolet Tahoe ... 2008 Chevrolet Tahoe.

Jan 21, 2016 | 2008 Chevrolet Tahoe LTZ

1 Answer

1998 Chevy Suburban - service 4wd light comes on after running 4x4 for 2 mins


Well it could be the selector switch, but I doubt it.
Generally, the service light means something is not working that the computer controls. Solenoids and valves are a couple of possibilities.
The transfer case is shifted by solenoids commanded by the body computer based on the switch position on the dash.
You should be able to have a shop scan the body computer for trouble codes and proceed from there.
A basic code reader may not access the body computer.

Jul 05, 2012 | 1999 GMC Suburban

1 Answer

My 99 Chevrolet silverado 4wd not working.ive replaced the dash switch and still nothing .when I turn the key the 4wd switch lights stay on for a split second then goes off. What else should I try?


I have run into to this problem many times on these trucks, i have seen your problem and also where the 4wd high light wont work but 4wd low and 2wd work fine and the 4 wheel drive works fine. on your truck i will bet its the transfer case selector motor.
the motor is what turns the lights on when in the selected mode which goes through the 4wheel module under the dash, this sounds like a bad selector motor and that where i would start. this motor is located on the transfer case, it bolts to the rear of it.here is a picture of it to help you locate it. good day.4_14_2012_12_37_13_pm.jpg

Apr 14, 2012 | 1999 Chevrolet Silverado 1500

2 Answers

2004 traiblazer extended service 4 weel drive light comes on after 10 minute drive 4wd not working after that. light on 4wd switch is off. if a leave the truck alone for a day, 4wd will work....


I would find an independant shop that has a Tech 2 or equal scan machine....these can communicate with your TCM (Transfercase Control Module) and narrow down what the problem is.

Jun 23, 2011 | 2004 Chevrolet TrailBlazer

1 Answer

I have a 2004 GMC Envoy XL and the high range 4x4 mode will not engage. The AWD system works just fine as well as the 4x4 mode in low gear. What is causing this?


Is the Service 4WD light coming on? Do the light on the 4x4 selector switch indicate the proper selection and are on steady after a few seconds? If there is no Service 4WD light on and the selector switch light are correct, the only place for the problem to be is the Transfer Case. Has the Transfer Case fluid been changed at 50K mile intervals? This is very important.

Feb 01, 2011 | 2004 GMC Envoy

1 Answer

My isuzu dmax 4x4 manual (year model 2004) have a problem . . . "CHECK 4WD" warning light is always on. isuzu service shop tells me that the 4wd module and actuator needs to be replaced upon...


If the tech 2 device is indicating the code for 4wd module then it has to be replaced.Get the module and its connections checked before going to replace the module.If the module connections are getting short or loose then getting the connections repaired solves the problem.But most probably when it shows module problem,the module has to be replaced.The actual testing procedure is as follows:--- If you have an ODBII code reader, you can check if there are any codes stored in the ECU. There is also a diagnostics mode you can go into for transfer case issues:

1. Warm up the engine. Turn it off.
2. Turn the ignition switch on and off at least twice, then turn the ignition switch to off.
3. Shift into park.
4. Turn the 4WD selector to Auto.
5. Turn the ignition switch to on. Do not start engine.
6. Is the 4WD warning lamp on? Continue if no.
7. Shift into reverse.
8. Turn the 4WD selector to 2WD, Auto, 2WD.
9. Shift into drive.
10. Turn the 4WD selector to 4H, Auto, 4H.
11. Shift into neutral.
12. Turn the 4WD selector to Auto.
13. Shift into park.
14. The 4WD indicator light will come on for 2.5 seconds, then go out. It will then flash a series of times to represent a one or two digit code, with half-second delays within a number and 1 second delay between numbers. e.g. to represent the code 23, it will flash twice with 0.5 seconds between flashes, wait a second, then flash three times with 0.5 seconds between them.Get it rechecked again by disconnecting the 4wd module and reconnecting again,. --------------------Thank you.

Jan 24, 2011 | Isuzu Pickup Cars & Trucks

1 Answer

03 Chevy Tahoe Z71 - 4wd not functioning


my son has one and his did that and it was a fuse he put a new one in and it is working good now

Jan 14, 2009 | 1999 Chevrolet Blazer

Not finding what you are looking for?
2001 Dodge Durango Logo

655 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...