Question about 2006 Jeep Commander

2 Answers

How do I replace the rear brake light bulb on a 2006 Jeep Commander? I cannot find how to access the bulbs.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Anyone having a problem ( 2006 Commnader) with a replay when we go over rail road tracks, the dash lights dance and the ac fan goes on and off. I think it make be a relay, but my mechanic says bring it back when it is doing it, but it is suprratic. Any advice?

Posted on Aug 12, 2011

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 83 Answers

Get manual at AUTOZONE!! swampratt200!!AAAEEE!!!!

Posted on Jul 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a fuse for the 3rd brake light on a 2006 Jeep Commander?


No, but there is a 5 watt capless bulb in it. Probably blown.

Dec 21, 2016 | Jeep Cars & Trucks

1 Answer

Where is the emergency brake indicator switch located?


its on the handle of most cars made.
after all the cables go rear and putting switches under car
is problematic.

xk jeep
the FSM book covers this fully, as does all things,unique to your jeep. get one?

gain access to lever. (console removed)
see lever ,see switch and wires, there, bingo.

best i can do, no commander fsm , here.

Mar 10, 2015 | 2008 Jeep Commander

2 Answers

2006 Jeep Commander Tail light


The tail light circuit is separate from the brake and turn signal circuit. Either the bulb socket has gone bad or a wire has flaked out. Check for voltage at the socket on either pin base when you have your parking lights on. If voltage is present, it is either a worn socket failing to hold the bulb properly, or another bad bulb. If no voltage, determine which wire on the other side is tail light power, and run a new wire across to the side that isn't working and connect it to provide power.

Apr 09, 2014 | 2006 Jeep Commander

1 Answer

How do you replace headlight bulb on 2006 Jeep Commander


Look behind the headlight in engine bay and see if there is a black plastic cover. If there is it should easily unsnap and the bulb sockets with attached wiring will be visible. If you have Xenon lights it's abit more involved. Most parts stores will either show you or install for you.

Feb 05, 2011 | 2006 Jeep Commander

1 Answer

How to remove 2007 jeep commander climate control panel for light bulb replacement


The lights in the climate control panel are not bulbs, they are LED and the entire panel will need to be replaced. I would check for a bad connection before replacing the panel assembly.

Dec 28, 2010 | 2006 Jeep Commander

1 Answer

How do i change the brake light on jeep liberty 2006?


1) You will need to open the rear swing door.

2) On the inside jam there are two torx headed screws (T-15's if I remember correctly).

3) Unscrew the two torx screws.

4) The light is now held by two mounting tabs (small spherical headed plastic sets that go through a rubber grommet).

5) You will need to pry the light casing off (easy pressure with a good size flat head screw driver will do the trick).

6) The light bulbs are twist mount settings inside the light casing.

7) Twist out the mount setting, change the bulbs, and reset the light mountings.

8) To put the light casing push the light casing back on and put in the screws. Everything else will work in reverse when it comes to assembling the whole unit.

2006 Jeep Liberty Replacement Light Bulb Sizes
Low Beam Headlamp Bulb Size: 9007
High Beam Headlamp Bulb Size: 9007
Parking Light Bulb Size: 2825 or 3157
Front Turn Signal Light Bulb Size: 3157
Rear Turn Signal Light Bulb Size: 3757ALL
Tail Light Bulb Size: 3157
Stop Light Bulb Size: 3157
High Mount Stop Light Bulb Size: 921
Fog/Driving Light Bulb Size: 9145 or H3-55W
License Plate Light Bulb Size: 168
Back Up Light Bulb Size: 3157
Front Side Marker Light Bulb Size: 168
Ash Tray Light Bulb Size: 161
Map Light Bulb Size: 578
Dome Light Bulb Size: 578
Step/Courtesy Light Bulb Size: 906
Trunk/Cargo Area Light Bulb Size: 578

Thank you for using fixya, and good luck

May 08, 2010 | 2006 Jeep Liberty

1 Answer

How to change the park light bulb on a 2006 jeep commander


open the trunk and pull the cover off the back of the light and bingo its right there

Dec 06, 2009 | 2006 Jeep Commander

1 Answer

Right passenger brake light doesn't work but parking light and turn signal does. Is the bulb bad?


Most likely yes, most bulbs that are used for both the brake light and turn light have 2 separate filaments in them basically making 2 bulbs into one, to which frequently one of those filaments will burn out but the other will still work. The replacement bulb type will be in your owners manual, or you could just take out the bulb and read the number off of it.

Jul 19, 2009 | 2007 Jeep Commander Rocky Mountain

2 Answers

My high level brake light has bruned out,(third brake light). I was informed by the dealer the back window panel has to be removed to replace the 3.00 dollar bulb, total cost 75.00 dollars. With some


replace the bulb...??? This requires you remove the rear package deck (to access the bulb & socket). to do this, remove the seat bottom (two bolts hold the rear seat bottom to the chassis, then remove the bolts which hold the shoulder cushions (LH & RH - 12mm bolts) then remove the cosmetic molding around the trunk access (7 to 8 screws) then remove the "C" pillar covers (SRS curtain airbag LH & RH) to access the rear deck package & access the third brake lamp bulb. replace it, then reassemble.

May 26, 2009 | 2006 Hyundai Sonata

1 Answer

Break kight burned out


Open the liftgat and you should see the screws on the side of the lamp. Unscrew then and pull the lamp away from the vehicle. There should be sockets in the tailamp that screw in and out about the size on a half dollar. Pull this out and pull the bulb out straight and replace by pushing in a new bulb. Follow these directions backwards to replace the lamp. Hope this helps.

Jan 12, 2009 | 2006 Jeep Commander

Not finding what you are looking for?
2006 Jeep Commander Logo

1,561 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...