Question about 1987 Chevrolet S-10 Pickup

1 Answer

1987 chevy s10 need fule injector replacement. I have removed the injector but the o ring inside was damaged and there was only 1/2 of the o ring there. Is there any reason to worry about the missing piece of o ring and is there any special installation instruction to install the new injector

Posted by on

  • dispatch276 Jul 21, 2009

    i looked inside very well and didt see the old o ring. so the new o ring only goes on the base of the injector and then install as it came out?

  • Richard Scordino May 11, 2010

    If there's no obvious place the ring could have gone, just put a bit of oil on the new ring and install the part.If it went down through the throttle plate the engine will eat it with no problem.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 359 Answers

Make sure the old o-ring isn't in the hole a little light oil on the new o-ring and it should slip right in.

Posted on Jul 21, 2009

  • Dennis Gentz
    Dennis Gentz Jul 21, 2009

    yes, all the best mate

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1988 chevy S10 2.5L tbi


out of time. get piston num. 1 to top dead center on compression stroke then make your rotor on dist. point to #1 and it should fire up. you may have to then turn the dist. some to get in in specs.

Feb 18, 2014 | 1998 Chevrolet S-10 Pickup

1 Answer

We need to replace drivers door on 1987 chevy s10 and can find only 1 bolt. What all needs removed to replace door?


the door henges are welded on the s10 you will need to remove the henge pins in order to remove the door, get some help! it will take 2 of you to get the door off and a floor jack helps a lot. you can get a tool called a pin popper and i recomend you do it makes the job much eazer, and the tool kit comes with the procdeger to remove the pins, when reinstalling the door replace the pins and bushings they come as a kit and can be bought at almost any auto parts store......good luck

Jul 06, 2011 | Chevrolet S 10 Cars & Trucks

1 Answer

My 1987 chevy s10 wont start unless i poor gas in the carb. When i turn the engine over i see gas coming out of the injectors.


Hi and welcome to FixYa!

Looks like that you have a faulty coil pack. If the coil is faulty there will be no current to the plugs so I strongly suggest that you have the coil pack be replaced. It is inside the cap where the spark plug wires are connected. You will need to remove the cap to gain access on the coil pack and have it replaced with a new one.

Hope this helps and thank you for using FixYa! Have a good one!

Feb 22, 2011 | 1986 Chevrolet Camaro

1 Answer

I have an 87 s10 blazer with 2.8L I Replace tbi


on a vehicle that old the wires are brittle start at the injector and check for cracked or broken wire in the harness

Nov 23, 2009 | 1987 Chevrolet S-10 Pickup

2 Answers

Replacing the o rings on a 95 chevy s10 2.2


The Injectors are right there in opening of the throttle body. There are not individual injectors for each cylinder.
There 2 or 4 injectors that spray the gas right on top the throttle plate. The entire manifold is filled with the gas/air mixture.

Oct 04, 2009 | 1995 Chevrolet S-10 CA Edition

1 Answer

1987 chevy s10 fuel injector problem. Install new fuel injector but fuel comes out steady causing engine to idle high and bog down when i step on the gas pedal. i have previously replace swapped ecm and...


Check the fuel pressure at the shredder valve, you should have 13 to 13.5psi, anything other then that will give you problems in the GM TBI. If the pressure is bad, then you may have to replace the fuel pressure regulator at the bottom of the TB. 
Good luck and keep me posted. 

Jul 22, 2009 | 1987 Chevrolet S-10 Pickup

2 Answers

1987 chevy S10 engine idle problem


relace the throtle air idle valve.The temp switch will allso cause this problem.

Jul 19, 2009 | 1987 Chevrolet S-10 Pickup

2 Answers

1987 chevy engine problem


you have to reset base idle see manual at library for procedure

Jul 19, 2009 | 1987 Chevrolet S-10 Pickup

1 Answer

How do you replace a fuel injector on a 3.4 V6 in a Chevy Venture?


You will need to remove the fuel rail, pull the injector out and put new one in. Only thing you need to remember is that you have to pay attention to "o" ring seal, making sure you remove the old one and not damage the new one. There are specific instructions for removal in any inexpensive manual.

Mar 19, 2009 | 2000 Chevrolet Venture

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...