Question about 2000 Nissan Altima

2 Answers

Need ECM for 2000 Altima - 2000 Nissan Altima

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 6,784 Answers

HI, this is a dealer part. this means that, you can only purchase this device from the dealer. Contact your local Nissan Dealership parts department so that you may order this asap.

You can also search the local salvage yards as well for used ECM's. ((This is not recommended)).

Posted on Jul 21, 2009

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 33 Answers

Have you checked in your local area for companies that deal in used or refurb. ecm..most request that you have your original

Posted on Jul 21, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to fix p1065 code problem in nissan altima 2005

- ECM Harness power supply circuit is open or shorted
- ECM Harness ground supply circuit is open or shorted
- ECM may be faulty

Jul 03, 2015 | 2005 Nissan Altima

1 Answer

What would cause 2012 nissan altima to have no power to obd?

1999 all other models to 2000.the data link on Nissan have to switched on at the side of the ECM that is turned by a screw driver . The procedure is to access the ECM -switch ignition on(do not start engine)--turn diagnostic mode selector on ECM fully clockwise.--wait 2 seconds--turn diagnostic mode selector on ECM fully counter clockwise. Lights will flash a code of long and short models 20002001 and on can only be read by a scan tool connected to a data link connector.

Jul 28, 2014 | 2012 Nissan Altima 2.5 Sedan 2.5L 4-cyl....

1 Answer

2002 Altima cranks no start. Dealer said that the bcm ecm and immobilizer all need to be replaced. Had to come up witht he money so I had the car towed back to house. Now the dealer is saying that the dash...

Did your Check Engine or Service Engine Soon light come on? If so, did you read the code stored in the ECM? If so, what was (were) the code(s). It's unlikely that the ECM and BCM would both completely fail at the same time. More info please.

Oct 03, 2013 | 2002 Nissan Altima

1 Answer

Nissan altima 2000 with engine service light on. fault codes per mechanic p0325 and p1126. But he said mass air flow sensor malfunction. is this right?

p0325 is, ignition system or misfire, could be plugs, wires, or a bad coil. p1126 throttle control motor relay curcuit open.P1126 Power supply for the throttle control motor is provided to the ECM via throttle control motor relay. The throttle control motor relay is ON/OFF controlled by the ECM. When the ignition switch is turned ON, the ECM sends an ON signal to throttle control motor relay and battery voltage is provided to the ECM. When the ignition switch is turned OFF, the ECM sends an OFF signal to throttle control motor relay and battery voltage is not provided to the ECM. possible cause, Harness or connectors (Throttle control motor relay circuit is open Throttle control motor relay.

May 07, 2010 | 2000 Nissan Altima

1 Answer


Check your cigarette lighter fuse to see if it is blown. Some vehicles use this circuit to power up the data link connector.

Jun 21, 2009 | 2000 Nissan Altima

1 Answer

ECM 2003 Altima

replace crank-positioning senser

Jan 24, 2009 | 2003 Nissan Altima

1 Answer

Evaporator Box in Altima

You cant remove it because there are 2 pipes attached to it under the hood. You actually need to recover the R134 out of the A/C system and undo those 2 pipes to get it out. There may by some more screws that hold it in. See if your Altima has a small opening, that may be covered (incabin filter hole) Some 2000 models started coming out with incabin filters and that's how they get replaced. It would be visible since you have the glove box out. You will see a small cover 1 inch wide and about 6-7 inches long. If you don't see anything like that, than you don't have the slot for the filter. If you have the opening, (right above the blower motor) remove the cover and look in the slot. You will see the evaporator and inside of the box and what is in there aka pine needels etc.
As far as the ECM goes, those are car specific and can not be mixed. You need the ECM with the same part number as the one that came with the car originally. Good luck.

Oct 20, 2008 | 2000 Nissan Altima

1 Answer

Need an ecu wiring diagram pinout for a 2000 nissan altima SE 5spd

what is the car doing?? by you saing "need a ECM diagram?" what is the problem with the car. that car is pretty bulletproof and I have't seen any ECM issues unless your A/C drain is clogged up and water leaked onto/into your ECM frying it up. Let me know what your symptoms are.

Jul 29, 2008 | 2002 Nissan Altima

Not finding what you are looking for?
2000 Nissan Altima Logo

Related Topics:

370 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

75817 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

723 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides