Question about 1998 Toyota RAV4

1 Answer

Tell me how to remove gearbox - 1998 Toyota RAV4

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 26 Answers

The best and quickest way is to remove both engine and trans together as a single unit out of the BOTTOM of the Rav4. This is how the service was designed. I can send you cutsheets with visual diagrams if you need it is a 2 page replacement procedure for the Rav4 2wd. I'm assuming the 4wd is much more work.

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm replacing the clutch. I have removed all the bolts and separated the the housing slightly but cannot totally separate the two. I'm thinking I may be missing a step.


in the same area of the bolt wholes there will be dowels sometimes the gearbox just needs to be pryed to seperate also make sure the driveshafts are completely removed from the gearbox shift cables and hydraulic line is removed mountings are removed completely out of the gearbox way.sometimes the loom or water hoses routed over the gearbox can restrict and its common for the cv joint flange on the gearbox differential to hook on the metal shim plate thats sandwiched between the engine and gearbox

Mar 16, 2016 | 2002 Kia Sportage

1 Answer

How to remove 1400 Nissan gearbox out


1 Remove battery earth cable.
2 Remove gear shift lever - usually just pulls out.
3 Remove starter motor.
4 Remove bolts holding prop shaft to gearbox final drive, and remove the prop shaft.
5 Remove all bolts around bell housing holding bell housing to engine.
6 Slide gearbox back to slide spigot shaft from clutch plate.
7 Slide gearbox from under vehicle.
Gearbox is now removed out.

Jan 02, 2015 | Nissan Cars & Trucks

1 Answer

Steps to removing a transmission from a GMC ENVOY 2004 V6, 4WD.


Park the vehicle in a clean dry well lit place. Work with safety in mind. Its always good to take pictures as you strip the/ a assembly. Refer back to pictures if you get stuck. Dis-connect the battery. Remove the gear linkages and speedo-drive and power cables from the gearbox. Remove the starter motor. Loosen the propshaft. Mark the yokes of the propshaft- for upon installation to avoid an unbalanced propshaft. Loosen the centre bearing. Remove the propshaft. Remove the cross member underneath the gearbox if there is one. Loosen bolts around the gearbox to cylinder block. Use a gearbox jack to support the gearbox. Take the bolts out from the gearbox to cylinder block. Pull gearbox backwards. Lower the gearbox. This is pretty much the standard way of removing gearbox. Note, there might be a transfer box, normally with 2 propshafts. Mark the yokes. Remove propshafts, transfer box and then gearbox. Remember to always work safe.

Dec 19, 2014 | Cars & Trucks

1 Answer

2010 Peugeot 207 gearbox drain/filler/level bungs


The drain plug is situated on the final drive casing at the rear of the transmission (plug may need a square or hex drive wrench).

There is no level plug - the correct qty of oil must be measured and then poured in.
If Petrol 1.9 ltrs, diesel 2.0.

The oil is 75/80w.

Jan 19, 2014 | 2008 Peugeot 207 CC

1 Answer

Clutch , presure plate and gearbox remove


You need the right equipment and knowledge to do this job there are a lot of cables wires etc that need to be removed before the gearbox can be loosened and removed.
There are also a lot of special tools required and the job is best done on a ramp or pit to gain access.
Trying to do this on the ground would be difficult and very dangerous also the engine needs to be suspended when the gearbox mounts are removed.
It is impossible to remove the clutch pressure plate, plate and hydraulic bearing on the C4 without removing the gearbox.
Take it to a garage/ clutch specialist.

Dec 26, 2013 | Citroen C4 Cars & Trucks

1 Answer

Front diff oil leak


remove entire trans,remove 8 bolts and then remove front differential case at this time you will need to remove torque convertor with tube do not remove this tube from the convertor it drive the oil pump, the gasket is liquid gasket make sure surface is clean,also at this time replace torque convertor seal and seal tube this tube seperates transmission fluid from gear oil good luck

Aug 13, 2009 | 2001 Subaru Forester

1 Answer

How to remove the gearbox from a 1999 suzuki swift car


disconnect battery remove it & its cradle
jack it up & drain gearbox oil
remove the wheel & undo the axle nut in the centre!
[do not remove it yet]
undo the bottom control arm at its pivot point under the axle then seperate them !
pull swiftly outward to remove the drive shaft from the gearbox!
now there is the gear selector & speedo & clutchcables & starter motor to diconnect & or remove
remove gearbox mount But support the motor from underneath
undo all the bolts around the gearboxes bellhousing!
use a pry or large flat bladed screwdriver to part the gearbox from the engine & lift gearbox up & out! its very tight squeeze in there!!
Im sure now that you regret asking lol
dont forget while its out you may aswell do the clutch
good luck!
Cheers Rob.

Jul 20, 2009 | Suzuki Swift Cars & Trucks

1 Answer

Reversing switch on 2000e gearbox


it is located on the side of the gearbox either on the rear extension housing or in the middle main gearbox housing it should have 2 wires comming out of it

Apr 12, 2009 | Ford Escort Cars & Trucks

1 Answer

BEARINGS WORN IN GEARBOX


disconnect lower arms, and remove driveshafts..disconnect all wiring and remove bolts from gearbox bellhousing and remove gearbox from underneath the car

Dec 24, 2008 | 2006 Peugeot 504

2 Answers

Whats the best way to drop the gearbox & transfer case?


remove the carpet on the floor, remove the gear shift lever as well as the 4wd shift lever, remove the drive shaft (both) remove the bell housing bolts, remove the starter, place a hydraulic lift jack below the gear box , then remove the wiring connectors , then remove the cross member , then pull the gearbox out from its positin, drop the gearbox very carefully, when gearbox is on the floor, make sure its sittin on a up right position so it dose not spoil any of the elctric connectors especially the reverse light switch...(that seems to be the easiest way to remove a manual land cruiser gearbox) hope that wil help....

Oct 25, 2008 | 2001 Toyota Land Cruiser

Not finding what you are looking for?
1998 Toyota RAV4 Logo

Related Topics:

527 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...