The torque specs when replacing the inake gaskets on a 97 Lumina 3.1 liter enne

it has to be done in stages, if you go to the autoparts store you can get a book for your car and it will give you the specification for the torque specs and sequence and any other that you need

torque hyundai accent Questions & Answers - Fixya

www.fixya.com > Forum > Tags

Torque specifications for cylinder head 2000 hyundai accent Are you aware that ... cover gasket on my 1997 Hyundai Accent GLS (engine code G4EH, 1.3L).

Hyundai Alpha engine - Wikipedia, the free encyclopedia

https://en.wikipedia.org/wiki/Hyundai_Alpha_engine

WikipediaG4EH in a 1999 Hyundai Accent L ... lb·ft (132 N·m) at 4000 rpm, although some websites quote the torque rating as being 97 lb·ft (132 N·m) at 2700 rpm. ... 1992 Hyundai S-Coup? LS specifications - Carfolio.com · 1992 Hyundai S-Coup? GT ...

[PDF]AERA Torque Specs

www.aera.org/uploads/4/3/7/7/43776611/aera-torquespecs.pdf
AERA Torque Specs. 500 Coventry Lane, Suite 180, Crystal Lake, IL 60014. Toll-free Technical Hotline: 1-888-324-2372 (1-88-TECH-AERA). 815-526-7600 fax ...

.

Torque Specifications - AutoZone

www.autozone.com/.../Hyundai.../Specifications/Torque-Speci...

AutoZoneTorque Specifications. Print. Specific to: Hyundai ... Specific to: Hyundai Accent2006. Hyundai Azera 2006. Hyundai Elantra 2006. Hyundai Sonata 2006.

Club Accent Qu?bec • Consulter le sujet - hyundai motor s

did you follow bolting pattern? Did you follow the torque specs?

Hi,
This should help you out.


Let me know if you need more information.
Thanks
Jason

You'll need to change the oil and filter, antifreeze and maybe add some high heat silicon sealant for around the holes in the head gasket.

remove the throttle body,remove the valve cover,remove the intake manifold bolts. you SHOULD be able to GENTLY pry the intake back enough to remove the gasket. be careful as to not scratch or ding any surface that comes into contact with the gasket.clean the gasket surfaces thoroughly and install the gasket. install in reverse order. make sure that you torque all bolts down to specs and in the order called for. on a final note...yu may have to remove the EGR valve to get some clearance to make it easier

Torque sequence ------------------ front | 12 8 4 1 5 9 13 | of | | engine | 11 7 3 2 6 10 14 | ------------------ Final torque must be reached in 3 equal steps Step 1: torque all bolts (except bolt 11) to 110 Ft/Lbs Step 2: torque bolt 11 to 100 Ft/Lbs Recheck final torque in sequence.

1. Disconnect the negative battery cable.
2. Drain the cooling system.
3. Disconnect the hoses at the thermostat housing.
4. Properly relieve the fuel system pressure.
5. Remove the cylinder head cover.
6. Loosen the rocker arms.
7. Remove the pushrods.

The valvetrain components must be replaced in their original positions.

1. Remove the intake and exhaust manifold from the cylinder head.
2. Disconnect the spark plug wires and remove the spark plugs.
3. Disconnect the temperature sending unit wire, ignition coil and bracket assembly from the engine.
4. Remove the accessory drive belt(s).
5. Unbolt and set aside the power steering pump and bracket. Do not disconnect the hoses.
6. Remove the intake and exhaust manifold assembly.
7. If equipped with A/C, perform the following:
   1. Remove the compressor and position it aside with the lines attached.
   2. Remove the compressor bracket bolts from the cylinder head.
   3. Loosen the through bolt at the bottom of the bracket.
   
   
8. Remove the alternator.
9. Remove the cylinder head bolts, the cylinder head and gasket from the block.

Bolt No. 14 cannot be removed until the head is moved forward. Pull the bolt out as far as it will go and suspend in place by wrapping with tape.

1. Discard the gasket. Thoroughly clean the head-to-block mating surface.
2. Clean and inspect the cylinder head thoroughly. Refer to the engine reconditioning portion outlined later in this section.

To install:

1. Coat a new head gasket with suitable sealing compound and place it on the block. Most replacement gaskets will have the word TOP stamped on them.

Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

looks like there is special sequence to reassemble and tightening, a quick note replace any bolts that have two punch marks.tighten as follows: x x x x x 10 4 2 6 8 x x x x x 7 5 1 3 9 torque all down to 15 ft lbs torque to 30 ft lbs plus 90 degrees. Good luck!

Hi
1 drain the coolant
2 there will be a pulley with 4 10mm bolts loosen them
3 remove the belt
4 now remove the 4 10mm bolts and remove the pulley
5 that's the water pump there are 5 bolts to remove (8mm)
6 after removing the bolts tap the pulley flange to remove the pump
7 clean the old gasket off the front cover
8 install the new pump and gasket and reassemble

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): Foot pounds (Final torque) Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. Foot pounds (Final torque) Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.