Question about Ford F

1 Answer

The hydraulic rod keeps slipping off the pedal.....how can i resolve this?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,071 Answers

I believe there is a clip that holds rod to pedal you will need a new clip

Posted on Jul 21, 2009

  • paul campbell Jul 21, 2009

    i believe there is a clip that holds rod to pedal you will need a new clip

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need a clutch pedal diagram for a 1999 s10 2.2 4cyl manual trans


Sorry no diagram. But here is how it works. In the start position(Power) the wire goes to the start fuse, from the fuse it goes to the clutch pedal switch. Push the pedal and it goes to the starter relay. On the other end is ground. If it is good it pulls the relay closed. On the closed end is battery power to the starter.

Mar 09, 2016 | 1999 Chevrolet Silverado 1500

1 Answer

Do you seal with x type jaguars


If hydraulic system has a retractable push rod behind clutch pedal you may try releasing it slightly . this seems to be a clutch replacement problem.

Dec 24, 2014 | Cars & Trucks

1 Answer

Can the clutch be adjusted in a 2002 Ford Laser KQ?


No it is a self adjusting hydraulic type. If it slips or the pedal has no play the clutch disk is worn out.

Jul 10, 2012 | Cars & Trucks

1 Answer

Clutch pedal on ford fusion 3 goes down pin or something comes out


My clutch pedal kept slipping off the rod. I attached a washer with screw tightner to the rod. The pedal nows stays put and does not slip off

Jun 24, 2012 | 2004 Ford Fusion

2 Answers

Clutch is not easy to cut and a sound when is running


Not easy to cut ???? Not sure what you mean by this, but imprezas are notorious for failing clutches......it is the weakest link unfortunately.....

Has the clutch been recently replaced ?????

How many miles are on the clock ???

What kind of noise are you hearing ???

Feb 24, 2011 | 1998 Subaru Impreza

1 Answer

Burnt smell from clutch when im in 3rd gear


It sounds like the clutch is close to being worn out as the pressure plate is not gripping the clutch plate with sufficient force when power is applied. Before you consider replacing any thing, first check the clutch free travel adjustment because as the clutch plate wears the free travel does decrease and if there is no free travel, then there will be some releasing action on the pressure plate allowing cluth plate slip. Hydraulic setups are usually self adjusting but you should check the free travel of the clutch pedal which should be about 3/8 to 1/2 inch measured at the pedal rubber. This is done by adjusting the push rod that links the pedal arm to the piston in the master cylinder. Adjust by first loosening the locknut on the rod at the end where it attaches to the pedal arm and turning the rod in either direction to obtain the correct free travel. One adjusted retighten locknut.
For a cable setup there should at least 1/8 inch of free travel of the cable before it starts to move the clutch fork on the outside of the bell housing. To adjust, hold the operating fork so that the release bearing is touching the fingers of the pressure plate. You will need to turn the cable adjuster so there is only about 1/8 to 1/4 inch of free travel of the cable where it attaches to throw out fork before it starts to move the fork when the pedal is depressed.
If all adjustments are correct and clutch is still slipping then the pressure plate diaphragm spring has lost its tension and /or the clutch plate has worn down to the rivets. Either way you will have to do a complete clutch rebuild.

Oct 28, 2010 | 1989 Volvo 240

1 Answer

I noticed there is threaded adjustment on the clutch pedal push rod going into the clutch's master cylinder hydraulic system. Is this one way I can adjust the hydraulic clutch on my 1998 suzuki sidekick...


Yes, if you need a little oomph out of the pedal, you can get a little more throw out of the adj rod, or you can get a little less, it doesn't take much to move a clutch. Depends on what the clutch is doing, chattering, slipping, grinding, not shifting. You know, that kind of stuff all gets different adj. Check it out.

Jul 07, 2010 | 1998 Suzuki Sidekick

2 Answers

Clutch bites high up on pedal movement


check clutch master cylinder rod adjustment and pedal height should be just higher than brake pedal. could try and bleed system also.
most hydraulic clutch systems have high take up points, adjust master cylinder rod, check for free play at top after adjusting if all that is O.K. then clutch plate may be nearly worn out but not slipping at this stage.

Jul 29, 2009 | 1997 Ford Escort

3 Answers

1991 Toyota pickup 4WD clutch slipping


There is an adjustment for the clutch pedal under the dash where the push rod goes thru the firewall. There is only aprx. 1/2" of adjustment so be careful when making an adjustment, if your clutch is slipping then you need to shorten the throw of the push rod.

May 06, 2009 | 1991 Toyota Pickup

2 Answers

Clutch slipping when it get hot


Check the adjustment of the clutch push rod. It is the rod that connects the clutch pedal to the clutch master cylinder.

Dec 22, 2008 | 1992 Isuzu Amigo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...