Question about 2003 Honda Accord

1 Answer

What is the procedure for changing the steering wheel?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 33 Answers

My advise is if you've not removed one before..Don't!....however if you've a mechanical aptitude get a service manual on your vehicle and it should be covered there

Posted on Jul 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What parts have to be removed to change output speedsensor on 97 sebring convertible jxi?


Hi Nicholas, Im AL the owner of Big As Auto Repair.

FRONT WHEEL SPEED SENSOR

REMOVE
  1. Raise vehicle on jack stands or centered on a frame contact type hoist. See Hoisting in the Lubrication and Maintenance section of this manual, for the required lifting procedure to be used for this vehicle.
  2. Remove the tire and wheel assembly from the vehicle.
  3. Remove the speed sensor cable routing bracket Speed Sensor Cable Routing Brackets from the steering knuckle. Remove the wiring harness sealing grommet retainer and speed sensor routing bracket from the inner fender.
  4. Remove speed sensor sealing grommet from the inner fender Wheel Speed Sensor Connection To Vehicle Wiring Harness Then unplug the speed sensor cable from the vehicle wiring harness Wheel Speed Sensor Connection To Vehicle Wiring Harness
  5. Remove bolt Speed Sensor Head Attachment To Steering Knuckle attaching the speed sensor head to the steering knuckle. Then remove speed sensor head from steering knuckle. CAUTION: If speed sensor head locating pin has seized to the steering knuckle, do not attempt to remove speed sensor head by grasping with pliers and turning. This will damage the speed sensor head. Use only the following procedure.
  6. If speed sensor head can not be removed from steering knuckle by hand, the locating pin on the speed sensor head has seized to the steering knuckle do to corrosion. Remove speed sensor head from steering knuckle using the following procedure. Remove disc brake caliper from steering knuckle, and remove brake rotor from hub/bearing assembly. Then insert a pin punch through hole in front steering knuckle Speed Sensor Head Removal From Steering Knuckle and tap speed sensor head locating pin out of steering knuckle.
Hope this helps and please visit my auto-repair-website at:
http://www.bigasautorepair.com/

Oct 08, 2015 | Cars & Trucks

1 Answer

How to replace steering wheel position sensor on a 2006 Cadillac DTS?


Manual Steering Column with JL4) or
Steering Wheel Position Sensor Replacement (Power Steering Column with JL4) ?
Preliminary Procedure Remove the intermediate steering shaft. Refer to Intermediate Steering Shaft Replacement .
1
Steering Angle Sensor Adapter
2
Steering Wheel Position Sensor
Procedure Disconnect any electrical connectors as needed.
Tip
If reusing, secure the old steering wheel position sensor before removing it for proper alignment upon reinstallation. Refer to Steering Wheel Position Sensor Centering .

Callout

Component Name
Notice: Secure the steering wheel utilizing a strap to prevent rotation. Locking of the steering column will prevent damage and a possible malfunction of the SIR system. The steering wheel must be secured in position before disconnecting the following components:
?€¢
The steering column
?€¢
The intermediate shaft
?€¢
The steering gear

After disconnecting these components, do not move the front tires and wheels. Failure to follow these procedures may cause improper alignment of some components during installation and result in possible damage to the SIR coil.
Preliminary Procedure Remove the steering column. Refer to Steering Column Replacement .
1
Intermediate Steering Shaft Bolt
Procedure Remove the steering column boot seal in order to access the intermediate steering shaft bolt.
2
Intermediate Steering Shaft Nut
Notice: Refer to Fastener Notice in the Preface section.
Tighten
47 N?·m (35 lb ft)
3
Intermediate Steering Shaft
Tip
?€¢
If necessary, scribe location marks between the intermediate steering shaft and the steering column and the intermediate steering shaft and the steering gear to mark their alignment before removing.
?€¢
If replacing the intermediate steering shaft, transfer any scribe marks from the old one to the new one.

Callout

Component Name
Notice: Secure the steering wheel utilizing a strap to prevent rotation. Locking of the steering column will prevent damage and a possible malfunction of the SIR system. The steering wheel must be secured in position before disconnecting the following components:
?€¢
The steering column
?€¢
The intermediate shaft
?€¢
The steering gear

After disconnecting these components, do not move the front tires and wheels. Failure to follow these procedures may cause improper alignment of some components during installation and result in possible damage to the SIR coil.
Preliminary Procedures

  1. Remove the left side instrument panel insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Left Side .
  2. Remove the driver knee bolster. Refer to Driver Knee Bolster Replacement .
  3. Disconnect the intermediate steering shaft from the steering gear. Refer to Steering Gear Replacement .
1
Steering Column Nut (Qty: 4)
Notice: Refer to Title not found in the Preface section.
Tighten
25 N?·m (18 lb ft)
2
Steering Column
Procedure
  • Disconnect any electrical connectors as needed.
  • If equipped with AN3, disconnect the automatic transmission range selector cable. Refer to Automatic Transmission Range Selector Cable Replacement - Column .
  • Transfer any parts as needed.
  • Sep 12, 2015 | Cadillac Cars & Trucks

    1 Answer

    I changed my power steering pump and i dont know how to bleed it


    The power steering is not bled as in a normal bleeding procedure. To get all the air out of the system, fill the reservoir, run the engine, and slowly turn the steering wheel from one side to the other, not all the way to the stops, but almost all the way, or if you hit the stops at each end of steering wheel travel, do so very gently. Turning the wheels back and forth a few times should get the power steering back. Keep repeating until steering is normal. Don't let the reservoir run dry, it shouldn't, but keep an eye on it.. When done top it up.

    Feb 25, 2013 | Cars & Trucks

    1 Answer

    How to remove steering wheel, 2000 blazer


    Parts stores sell an inexpensive steering wheel removal puller. Follow repair manual removal procedure, so the air bag doesn't activate. The steering wheel is retained by a large nut on the steering wheel shaft. Remove the nut, and attach the puller to wheel-it should pull right off.

    May 16, 2012 | 2000 Chevrolet Blazer

    1 Answer

    Steering is noisy at slow speeds when turning


    This car is essentailly the same as the Lincoln LS & T-Bird.
    Here is their solution.

    please rate if this helps you. Thanks.

    ISSUE: Some 2003-2005 Thunderbird, Aviator, and Lincoln LS vehicles may exhibit steering gear squeak when turning the steering wheel, especially during low speed parking maneuvers. The noise may sound like it is coming from the steering column area and may be felt as a roughness in the steering wheel, while turning.
    ACTION: Refer to the following Service Procedure.
    SERVICE PROCEDURE NOTE: USE ONLY THE FLUID AND ADDITIVE SPECIFIED IN THIS ARTICLE. USING ANY OTHER FLUIDS OR ADDITIVES MAY RESULT IN SEAL DETERIORATION AND LEAKS.
    1. Open the hood and remove the power steering reservoir cap.
    2. Raise the vehicle on a hoist. Refer to Workshop Manual, Section 100-00.
    3. With engine off, drain power steering fluid by disconnecting steering lines and clamp plate from steering gear. Refer to Steering Gear Removal and Installation procedure in Workshop Manual, Section 211-00, follow only the steps required to disconnect the steering lines.
    4. Turn steering wheel lock-to-lock to drain fluid completely.
    5. Reconnect steering lines and clamp plate to steering gear. Torque retainer to 15 N-m (11 lb-ft) for Lincoln LS and Thunderbird, torque to 25 N-m (18 lb-ft) for Aviator.
    6. Lower vehicle.
    7. In a clean container mix 50 ml (10 teaspoons or 1.7 oz.) of Motorcraft Additive Friction Modifier, Part Number XL-3, with 50 ml of Motorcraft MERCON® Multi-Purpose Automatic Transmission Fluid, Part Number XT-2-QDX. NOTE: DO NOT PERFORM STEPS 8 AND 9 ON A HOT VEHICLE.
    8. Pour the above mixture into the power steering reservoir.
    9. Top off (fill) the power steering system with Motorcraft MERCON® Multi-Purpose Automatic Transmission Fluid, Part Number XT-2-QDX and reinstall the power steering reservoir cap.
    10. Raise vehicle on hoist enough so the front wheels are off the ground and can be turned from lock-to-lock.
    11. Start the engine and keep it at idle. Remain inside of the vehicle.
    12. Slowly cycle the steering wheel from lock-to-lock for two (2) minutes.
    13. Quickly and forcefully turn the steering wheel in one direction to full lock (either side). Bounce the steering wheel on/off of full lock twenty (20) times forcefully. NOTE: IT IS CRITICAL THAT THE STEERING WHEEL IS TURNED QUICKLY AND FORCEFULLY IN ORDER TO CREATE A PRESSURE SPIKE IN THE POWER STEERING SYSTEM.
    14. Repeat Step 13 in the other direction. Return the steering wheel to on center position.
    15. Slowly turn steering wheel to full lock in one direction (either direction) to achieve maximum pump pressure. Hold at full lock for one (1) second, then turn the steering wheel back 90 degrees as quickly as possible. Repeat this procedure twenty (20) times. NOTE: DO NOT HOLD THE STEERING WHEEL AGAINST THE STOPS FOR MORE THAN THREE TO FIVE (3-5) SECONDS AT A TIME. DAMAGE TO THE POWER STEERING PUMP MAY OCCUR.
    16. Repeat Step 15 in the other direction.
    17. Cycle the steering wheel slowly for 1 minute to confirm that the squeak is corrected and return vehicle to the customer. NOTE: IF THE SQUEAK CONTINUES, REPEAT STEPS 13-16 ONE ADDITIONAL TIME. IF THE SQUEAK IS STILL NOT CORRECTED PROCEED TO STEP 18.
    18. If the squeak is still present after performing Step 17, replace the steering gear. Refer to Workshop Manual, Section 211-00 for removal and installation procedures.

    PART NUMBER PART NAME XL-3 Motorcraft Additive Friction Modifier XT-2-QDX Motorcraft MERCON® Multi-Purpose Automatic Transmission Fluid 5W4Z-3504-A Steering Gear (LS) 5W6Z-3504-A Steering Gear (Thunderbird) 5C5Z-3504-AA Steering Gear (Aviator)

    Aug 15, 2011 | 2003 Jaguar X-Type

    3 Answers

    My ignition will not turn at all


    TRY ANOTHER KEY.MORE LIKELY IGNITION SWITCH KEYLOCK CYLINDER BROKEN.

    Feb 11, 2011 | 1998 Pontiac Bonneville

    1 Answer

    When turning steering wheel I have squeaking sounds coming from inside rubber boots that cover rods that steer front wheels and the power steering fluid has a burnt smell. ( I don't know the name of these...


    This is the steering rack. If it's not leaking fluid out of the bellows more than likely the fluid needs to be changed.
    This can be done by removing the 2 lines from the pump that attach to the rack draining the fluid, then reconnect the lines and refill with fresh power steering fluid.
    When draining make sure to take the cap/dipstick off of the pump.

    Nov 19, 2010 | 1999 Ford Taurus

    1 Answer

    I have a 2002 Yukon Denali and I was wanted to know, how do u change the bulb in the steering wheel?


    Steering Wheel Control Switch Assembly Replacement Removal Procedure
    1. Remove the steering wheel. Refer to Steering Wheel Replacement .
      399638.gif
      tif.gif
    2. Remove the horn switch from the steering wheel.
      755486.gif
      tif.gif
    3. Remove the steering wheel shroud retaining screws from the back of the steering wheel.
    4. Remove the steering wheel shroud from the steering wheel.
      408596.gif
      tif.gif
    5. Remove the steering wheel control switch mounting screws.
      780085.gif
      tif.gif
    6. Disconnect the steering wheel control switch (2) electrical connector (1).
      408598.gif
      tif.gif
    7. Remove the steering wheel control switch from the steering wheel.

    Steering Wheel Replacement Tools Required J 1859-A Steering Wheel Puller
    Removal Procedure
    1. Disable the supplemental inflatable restraint (SIR) system. Refer to Disabling the SIR System in SIR.
    2. Remove the inflator module. Refer to Inflatable Restraint Steering Wheel Module Replacement in SIR.
    3. Remove the horn switch. Refer to Horn Switch Replacement - On Vehicle .
    4. Make an alignment mark in order to note the relationship of the steering wheel to the steering shaft.
    5. Remove the steering wheel nut.
      374820.gif
      tif.gif
    6. Remove the steering wheel, using the J 1859-A .
    Installation Procedure

    Oct 04, 2010 | 1995 GMC Yukon

    1 Answer

    Replace airbag on `92 honda accord


    When an SRS cable reel assembly is removed and set aside during vehicle repairs, the cable reel may rotate inside the assembly so it is no longer centered. If the assembly is reinstalled with the reel off-center, the cable can break when the steering wheel is turned to full lock. The cable reel holding fixture locks the reel while the assembly is off the vehicle, keeping it centered for reinstallation.
    CABLE REEL REMOVAL PROCEDURE
    1. Follow the procedure in the appropriate service manual for disconnecting the battery, and removing the dashboard panels, steering column covers, airbag, and steering wheel.
    ^ Always install short connectors on the connectors for the driver's and passenger's (if so equipped) airbags.
    ^ Make sure the front wheels are pointed straight ahead before removing the steering wheel.
    2. Verify that the cable reel is centered; the yellow gear tooth is lined up with the alignment mark on the cover. Install the cable reel holding fixture in the cable reel assembly as shown. Use a TORX T-10 wrench.
    3. Disconnect the 6-P connector, then remove the cable reel assembly.
    CABLE REEL INSTALLATION PROCEDURE
    1. Verify that the front wheels are still pointed straight ahead.
    2. Reinstall the cable reel assembly, and reconnect the 6-P connector.
    3. Remove the cable reel holding fixture.
    4. Follow the service manual procedure for reinstallation of the steering wheel, airbag, steering column covers, and dashboard covers.
    5. Verify SRS operation as described in the service manual. Road test the vehicle.
    ^ If the steering wheel spoke angle is not correct, change it by adjusting the tie rod ends. Do not remove and reposition the steering wheel.
    PARTS INFORMATION
    Cable reel holding fixture:
    For 1992-95 Civic and Ohio-produced 1992-95 Accord
    P/N 77900-SPO-999, H/C 4733564
    For 1991 Accord Wagon, 1992-95
    Prelude, 1995 Odyssey and Japan-produced
    1992-95 Accord
    P/N 77900-SM5-999, H/C 4733572
    WARRANTY CLAIM INFORMATION
    Use the Flat Rate Manual information for the repair being performed.

    Jan 28, 2009 | 1992 Honda Accord

    2 Answers

    1997 dodge Intrepid: inner tie rod


    To Steering Gear Bolt 90 Nm (66 ft. lbs.) Jam Nut 75 Nm (55 ft. lbs.)
    NUMBER: 19-001-01
    GROUP: Steering
    DATE: Mar. 23, 2001
    THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN 19-003-00 REV A, DATED OCTOBER 6, 2000 WHICH SHOULD BE REMOVED FROM YOUR FILES. ALL REVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND INCLUDE PART NUMBER CHANGES AND ADDITIONAL MODEL YEAR.
    WARNING: FAILURE TO ACHIEVE A MINIMUM TORQUE OF 100 NM (74 FT. LBS.) MAY RESULT IN THE ATTACHING BOLTS LOOSENING AND FRACTURING. THIS COULD RESULT IN A SUBSEQUENT LOSS OF STEERING CONTROL. BENDING THE RETAINING TABS ALONE WILL NOT PREVENT THIS.

    SUBJECT:
    Loose Steering

    OVERVIEW:
    This bulletin provides service procedures and parts information for the inner tie rod bushings.
    MODELS:
    1993 - **2001 ** (LH) Concorde/Intrepid/LHS/New Yorker/Vision/300M
    SYMPTOM/CONDITION:
    Loose feel or clunk in the steering wheel as the wheel is moved from side to side.
    DIAGNOSIS:
    Observe the inner tie rod to steering gear attaching point while moving the steering wheel from side to side. If there is movement between the gear and inner tie rod, perform the Repair Procedure. If no movement is evident further diagnosis of the condition will be required.
    DISCUSSION:
    The inner tie rod bushings have previously been serviced with the tie rod assembly. This bulletin releases the parts, service procedures, and special tool necessary to service just the bushings. Subsequent service manuals will contain the Repair Procedure.

    Jan 13, 2009 | 1994 Dodge Intrepid

    Not finding what you are looking for?
    2003 Honda Accord Logo

    Related Topics:

    44 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    yadayada
    yadayada

    Level 3 Expert

    75051 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7726 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...