Question about Cars & Trucks

Open Question

Remove my details from on line a/c - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where in detail, is the orifice tube located, thanks


The tube is located at the high pressure inlet tube of the AC evaporator core at the rear of The engine compartment, the AC line that is small and high pressure goes to the connection point, remove the line after recovering the charge and inside is the tube.

Jul 07, 2012 | 1996 Chevrolet S-10 Pickup

1 Answer

How do you replace a fuel pump in a 1997 ford f350 crew cab


Removal & Installation 88285g11.gif

Details of the fuel pump assembly
Click to Enlarge 88285g12.gif

View of the fuel pump
Click to Enlarge

  1. Disconnect both battery ground cables.
  2. Properly relieve the fuel system pressure.
  3. Raise and safely support the vehicle securely on jackstands.

The electrical connector is located behind the fuel pump near the frame rail.

  1. Detach the fuel pump electrical connector.
  2. Remove the fuel line retaining clip and discard, then remove the fuel line from the fuel pump.
  3. Slide the clip up and off from the quick connect fitting. Insert the fuel line tool and remove the fuel pump delivery line.
  4. Unclip the brake lines from the fuel pump bracket.
  5. Loosen the pinch bolt and spread the mounting bracket.
  6. Remove the fuel pump.

To install:

  1. The installation is the reverse of the removal.

Oct 29, 2010 | 1997 Ford F350 Crew Cab

1 Answer

Cadillac seville sls '97 complete engine removal


the best way to do is dropping the engine and the transmission together with the sub frame
disconnect the rack and pinion, struts and brake lines
then you can separate the engine from the transmission once it's out.

Mar 14, 2010 | 1996 Cadillac Seville CA Value

3 Answers

How do you change a fuel pump and filter on a 2005 manual chevy aveo?


Removal & Installation
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Remove the rear seat.
  4. Remove the fuel pump access cover.
  5. Disconnect the electrical connector at the fuel pump assembly.
  6. Disconnect the fuel line.
  7. Remove the fuel pump assembly clip.
  8. Remove the fuel pump assembly from the tank.
  9. Remove and discard the gasket.

To install:
  1. Clean the gasket mating surface on the fuel tank.
  2. Position the new gasket in place.
  3. Install the fuel pump into the fuel tank in the same location as removed for ease of line and connector installation.
  4. Install the fuel pump assembly clip.
  5. Connect the fuel pump assembly connector.
  6. Install the fuel pump line.
  7. Install the fuel pump access cover.
  8. Install the EF10 fuse.
  9. Connect the negative battery cable.
  10. Perform an operational check of the fuel pump.
  11. Install the rear seat.

Mar 06, 2010 | 2005 Chevrolet Aveo

1 Answer

Replace fuel filter


  1. Relieve the fuel system pressure. For details regarding this procedure, please refer to Section 5 of this manual.
  2. If not done already, disconnect the negative battery cable.
  3. Raise and safely support the vehicle.
  4. Clean both fuel feed pipe connections and the surrounding areas at the in-line fuel filter with a clean rag to avoid possible contamination of the fuel system.
  5. Using a backup wrench, remove the fuel line fittings from the fuel filter.
  6. Either separate the quick-connect fittings or remove the fuel filter mounting screws, then slide the fuel filter out of the mounting bracket.
  7. Discard the fuel line O-rings and replace with new ones during installation.
To install:
  1. Install new O-rings to the fuel line fittings.
  2. Connect the fuel lines to the fuel filter.
  3. Position the filter in the mounting bracket, in the same position it was during removal. Using a backup wrench, tighten the fuel lines to 16 ft. lbs. (22 Nm).
  4. Install the fuel filter mounting screws.
  5. Carefully lower the vehicle. Install or tighten the fuel filler cap.
  6. Connect the negative battery cable.
  7. Start the engine and check for leaks.
25d7525.gif
Location of the fuel filter

9f0ac98.gif
Unfasten the retaining bracket can make removal of the fuel filter easier

2c6ca73.gif
Either use a clean rag or compressed air to clean the surrounding areas of the filter

523254f.gif
Use a backup wrench to disconnect the fuel line fittings from the filter

2e1fdd8.gif
Disengage the quick-connect fittings, then remove the filter from the vehicle

0d20d1f.gif
In-line fuel filter mounting and related components

It sits in front of the fuel tank.

Dec 07, 2009 | 1992 Buick Riviera

1 Answer

How do I change a fuel pump on my 1995 Ford F350 7.3 2WD Power Stroke Diesel Do I have to worry about the timing eccentric? How and what do I rotate?


Hi, I hope this helps...

1994-96 Engines
See Figures 3 and 4



0900c15280262dd1.jpg Fig. Fig. 3: Details of the fuel pump assembly-1994-96 diesel engine



0900c15280262dd2.jpg Fig. Fig. 4: View of the fuel pump-1994-96 diesel engine
  1. Remove the turbocharger assembly.
  2. Remove the fuel line banjo bolt at the pump.
  3. Remove the fuel line fittings at the rear of the cylinder heads.
  4. Remove the fuel lines assembly.
  5. Loosen the two hose clamps at the fuel pump fittings.
  6. Disconnect the water drain hose at the fuel filter.
  7. Disconnect the filter and position it forward.
  8. Remove the fuel pump retaining bolts, then lift the pump out of the crankcase bore.
  9. Remove the fuel pump tappet from the crankcase bore.

To install:
  1. Rotate the engine so the fuel pump eccentric is on the base circle.
  2. Install the fuel pump tappet in the base of the fuel pump.
  3. Replace the O-ring on the fuel pump base.
  4. Install the fuel pump and bolt it in place.
  5. Install the fuel filter and connect the water drain hose.
  6. Connect the two fuel hoses at the front of the fuel pump.
  7. Tighten the fuel line clamps and install the fuel filter retaining bolts.
  8. Install the fuel line assembly and new seal rings at the rear of the pump.
  9. Loosely install the fuel line fittings at the rear of the cylinder heads.
  10. Install the fuel line banjo fitting at the pump. Tighten the fitting to 40 ft. lbs. (54 Nm).
  11. Tighten the fuel line fittings.
  12. Install the turbocharger assembly.

Oct 13, 2009 | 1995 Ford F350

1 Answer

How do i change the radiator in a 2002 jaguar x type


As detailed as I can :
Drain the cooling system. Detach the air conditioning line .Raise the vehicle. Remove the lower radiator splash shield. The splash shield is equipped with hinges which should be treated with care on removal. Remove the radiator splash shield. Detach the securing clips. Remove the radiator splash shield. Seal the line and the evaporator with plugsDetach the air conditioning line. Detach the lower coolant hose. Remove the air conditioning condenser. Remove the securing screws. Vehicles with manual transmission, cable tie the cooling radiator. Detach the automatic transmission/power steering cooler. Remove the securing screws. Detach the automatic transmission/power steering cooler. Lower the vehicle. Remove the radiator foam trim. Remove the radiator. To install, reverse the removal procedure.

Aug 11, 2009 | 2002 Jaguar X-Type

2 Answers

Trouble removeing the fuel filter


You need what's called a "fuel line disconnect tool". It's held in place by a spring, and the tool slides in the opening to release the spring. Harbor freight sells sets of them for about $15.00. Other than that, you would need something to wrap around your fuel line, and slide into the opening to release the spring.

May 30, 2009 | 1995 Ford Thunderbird

1 Answer

Brake line under master cylinder rusted and spraying fluid


Replacing rusty brake lines is a nasty job, but u can do it yourself and save a ton of money. A while back, someone else asked this question and decided to have a garage do it, and it cost $1200. U can purchase different lengths of brake line at any auto parts store, along with connectors to join the lines together. The dealer won't have pre-bent lines for a car that old, but u can buy the different lengths necessary to replace the rotted line. You'll have to follow the line to see where it ends, which may be quite a distance away. The problem is, by the time u have to replace a line, they all need to be changed. The labor cost is high, but u can purchase the lines at a low cost. Get the car uo on jack stands, soak the line connections w/ wd-40 or some penetrating oil for a day (or more if possible) to help in removal. Replace a section at a time w/ lines u bend to fit as u go.Good Luck

Dec 28, 2008 | 1993 Oldsmobile Cutlass Ciera

1 Answer

Jetta heater core problem


Normally we remove the dash. Do you have air conditionning as an option because the A/C lines run into the same box and you can't remove them without emptying the lines properly.

Oct 12, 2008 | 1996 Volkswagen Jetta

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...