Question about Cars & Trucks

Open Question

Looking for 6 round moon clips - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rearview mirror on 2004 Chevy trailblazer is loose wont stay in position, looks like a round clip has popped out to hold mirror in place


The round metal piece needs to be glued to the windshield. Specific glue is sold at any autoparts store. Once glued in place, the mirror slides onto it.

Oct 08, 2016 | 2004 Chevrolet TrailBlazer

1 Answer

How to remove air sensor from 1.4 petrol fiesta 2002 Mk 6


My guess is someone has stripped the threads in he plastic housing. If you look on google images you will see most are removed by the hose clips on either side. The sensor itself having tamperproof screws. Look at the images to get a better idea but if you pry with a small screwdriver at the flange of the sensor at the same time unscrewing the head, you will probably find it winds out.

Nov 02, 2015 | Cars & Trucks

1 Answer

6 light 2 spot light low volt moon Raysystem trouble making a connection on 4They clip onto line fine wont stay lit Is there a way to clip the lights to the low voltage line better so they stay lit.


Not sure what you are needing here but if its a poor connection, try soldering the wiring or using correct spade and socket connectors.

May 25, 2015 | Cars & Trucks

1 Answer

I need to reprogram my 2004 ford focus sunroof, i believe that info is in the owner's manual


  1. 1. Tilt the moon roof into the vent position as much as possible and press on the front portion of the control.
  2. 2. Now release the switch.
  3. 3. Now press and hold that same switch again for 30 seconds or until the moon roof begins to move.
  4. 4. Now release the switch ans immediately press and hold the switch agaon.
  5. 5. Now the moon roof should close then open then close again.
  6. 6. You MUST wait until the moon roof has closed that second time before releasing the switch of the process will be a failure and you will have to start again.


  • Hope this helps.

Nov 04, 2011 | 2004 Ford Focus

1 Answer

How do u replace a heater blower motor in a ford focus 1999


Under the dash on the pssenger side you will find a round blower motor approx 6" round.Remove the electrical harness from it by pushing in the clip and then remove the 5-6 screws holding it in.Installation is the reverse order.Hope this helps

Jan 20, 2011 | 2000 Ford Focus

1 Answer

How to remove a wind up window handle


handle is retained by a 'clip' that fits into a groove in the widow regulator stem.with handle facing down,[6 o'clock] use a cloth under handle at the round part,give it a 'shoe shine' motion while pulling up on cloth to dislodge spring clip enough to grasp and remove it.you can also press back door panel & dislodge clip with a small flat blade screwdriver.

Oct 18, 2009 | 2000 Toyota Camry

1 Answer

How do i remove the lumbar knob?


there should be a clip behind the nob a half moon clip or screw in front

Aug 13, 2009 | 2005 Chevrolet TrailBlazer

1 Answer

I can`t change gears the gear lever has gone limp it feels like a clutch or clutch cable I neen a diagran og gearbox


Standing in front of the car walk around to the passenger side and look in to where the gear shift arm comes through the fire wall you will see a gear shift tube bellows with a clamp and bolt coming through and at the end you will see the "gear shift guide control"(7) there is a "gear shift control mode" (6) that clips over a round ball at each end one clip faces front and one back ,one towards the middle of the car and one closer to the passenger side of the car , this had come undone at both ends and dropped off, by replacing this the problem was solved.
The part numbers ( 7 ) and ( 6 ) are from a shift linkage diagram pages 21 and 22 found on the internet through http://www.daewooclub.cook/forums/showthread.php?tid=1002
I hope this is of help to someone else out there
Gary

Feb 20, 2009 | 2000 Daewoo Nubira

1 Answer

Replace struts on rear hatch door on 2005 Suburban


The hatch lift struts are held in place buy a half moon shaped spring clip at each end, use a flat blade pocket screwdriver and pry the clips up to release the ball socket and remove the strut from the ball pivot screwed into the body.

Aug 07, 2008 | Chevrolet Suburban Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...