Question about Cars & Trucks

Open Question

I require torque settings on a vw polo 8v BLM engine , cylinder head ,Mains & big ends, many thanks

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

steve_e_uk
  • 1675 Answers

SOURCE: golf iv 1.6 8v cylinder head torque settings

hi to tighten you have to do it in 4 stages as follows
1st stage 40nm leave 5 mins 2nd stage 60nm leave 5 mins 3rd stage 90 degrees leave 10 mins 4th stage 90 degrees then you are done i will try put order on here i hope this works as follows
10 4 2 6 8 front of engine back of engine 7 5 1 3 9

in that order hope this helps

Posted on May 10, 2010

jeffreyth82161
  • 180 Answers

SOURCE: mains and big ends torque settings for polo blm engen

It cannot done by me. It is better to seek help from a expert.

Posted on Sep 08, 2016

sandraspa25513
  • 180 Answers

SOURCE: how do i torque the mains and big end bearings on a polo blm engen

not possible

Posted on Sep 08, 2016

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque settings on a vw polo blm engine


Just Google torque settings vw polo blm engine. You probably did not get an answer because it depends on the part, or because nobody is going to do the Google search for you and then print out the answers.

Jan 03, 2017 | Volkswagen Polo Cars & Trucks

1 Answer

Mains and big ends torque settings for polo blm engen


It cannot done by me. It is better to seek help from a expert.

Sep 08, 2016 | Volkswagen Polo Cars & Trucks

1 Answer

What is the torque settings for polo bah motor big ends :mains and cylinder head


CHECK BELOW..
25458898-ms2db0pp00uj21y1nio4xcxs-1-0.png

Tightening torques
Bolted connections Tightening torque
Bolts, nuts M 6 10 Nm
M 8 20 Nm
M 10 45 Nm
M 12 60 Nm
Deviating from above
Exhaust pipe to manifold 40 Nm
Installation
Note
t Only remove the new cylinder head gasket from its packing immediately before installing.
t Handle the new gasket with extreme care. Damaging will lead to leaks.
- Place a clean cloth in cylinders so that no dirt or emery cloth particles can get in between cylinder wall and piston.
- Also prevent dirt and emery cloth particles from getting into the coolant.
- Carefully clean cylinder head and cylinder block sealing surfaces. Thereby ensuring that no scoring or scratches are formed (when using abrasive paper the grade must not be less than 100).
- Carefully remove metal particles, emery remains and cloths.
- Set No. 1 cylinder piston to TDC and then turn crankshaft back slightly.
- To centralize, screw guide pins from 3450/1 into front outer holes for cylinder head bolts-flechas-.
- Place the new cylinder head gasket in the centralizing pins -A-. Lettering (Part No.) must be readable.
- Fit cylinder head, screw in 8 remaining cylinder head bolts and tighten by hand.
- Remove the guide pins with tool 3450 by the bolt holes. To do this, turn the tool left until the pins are removed.
- Fit remaining cylinder head bolts and tighten hand-tight.
- Tighten cylinder head in tightening sequence as follows:
- Tighten all bolts to 30 Nm.
- Then tighten all bolts a 1//4 turn (90 °) further using a rigid wrench.
- Then tighten all bolts again a 1/4 turn (90 °) further.
Note
There is no requirement to retighten the cylinder head bolts after repairs.
The rest of the assembly is basically a reverse of the dismantling sequence.
Note
When the camshaft is turned, the crankshaft must not be at TDC. Danger of damage to valves or piston crowns.
Installing toothed belt and adjusting valve timing > Chapter.
Filling with new coolant > Chapter.
- Interrogate fault memory > Chapter.

Feb 21, 2015 | 2006 Volkswagen Polo 1.6

1 Answer

Torque settings


depends on your engine. If it's a VW air cooled flat 4, the mains which also ties down the engine casings, is torqued to 35 ft lbs and the cyl heads to15 ft lbs.
On more modern engines the mains can be torqued to 65 ft lbs, the big ends to 45 ft lbs and the cyl head to anywhere between 30 to 45 ft lbs.
A common remark among mechanics is to turn them till they strip, then a quarter turn back. Don't follow this rule.

Nov 05, 2014 | Cars & Trucks

1 Answer

Torque settings vw polo classic 1.6i mains and big ends


Want camshaft cap torque settigs for polo classic 1997 -1.6

Apr 23, 2012 | Volkswagen Polo Cars & Trucks

1 Answer

Require torque settings for a hyundai tucson 2008,gls petrol engine


Specifically which torque settings are you referring to. There are thousands to choose from. Please give an example such as "differential carrier", "cylinder head", "exhaust manifold to engine block" etc.

Mar 31, 2012 | 2008 Hyundai Tucson

2 Answers

Golf iv 1.6 8v cylinder head torque settings


hi to tighten you have to do it in 4 stages as follows
1st stage 40nm leave 5 mins 2nd stage 60nm leave 5 mins 3rd stage 90 degrees leave 10 mins 4th stage 90 degrees then you are done i will try put order on here i hope this works as follows
10 4 2 6 8 front of engine back of engine 7 5 1 3 9

in that order hope this helps

May 10, 2010 | 1986 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...