Question about Rover Cars & Trucks

Open Question

I have a 2003 Range Rover and it is in Low gear mode and it wont go back to the High mode

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Murphybanton
  • 2004 Answers

SOURCE: multiple fuses failing in range rover

Please ensure that all your fuses are replaced. you already know the reason why the cut in fuses occurred.

rate this.

Posted on Mar 24, 2009

Ad
  • 250 Answers

SOURCE: range rover 2003 transfer in neutral help please

hi, this is a long shot so dont give me negative if no joy.
on the p38 they suffer from a bad electronic selector.
now, i do not have a clue what gear box or transfer you have.
any way if you look at your transfer, beside where the prop comes out, is ther like a window wiper motor with 6 wires.
if so they get stuck, rust or dirt etc.
have you checked your fuses, alos i would add. again not sure on your model.
in the fuse box there is a blank fuse, when inserted it shifts it to neutral.
the dealers wont tell you where it is.
have you put any fuses in etc, i did this 5 year ago, a p38 was jump started, leads wrong way.
i got a call as the aa did not want to help anymore. aa had a hand full of fuses out, i stuck in were contacts were. after new ecu had no drive.
you are sure its not a gearbox fault, get back to me if not sure, i can tell you how to test this.

Posted on Aug 17, 2009

  • 54 Answers

SOURCE: Removal instructions for cd changer of 2003 Land

you need to open the whole Glove box then only you'll be able to get out your CD changer

Posted on Jul 05, 2010

  • 54 Answers

SOURCE: i have a 2003 range rover the air suspension inactive came on

it could be from many reasons...sometimes even the ABS system will cause this fault or even the Steering position Sensor. if it comes and goes then inspect your height sensors as the early version of the height sensors are getting weak and like melting so it gives wrong reading which cause the fault...offer more info. and you'll get your solution

Posted on Jul 05, 2010

  • 54 Answers

SOURCE: 2003 range rover power door locks do not work...

does the roof lamp work? if not then means your Vehicle in transport mode. to have it in normal mode you need to take it to a dealer or something equivalent to have the job done by approved diag. machine

Posted on Jul 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i engage into 4 Wheel Drive Mode on my V8 4.6 HSE


a 1999 landrover Range Rover is in constant 4 wheel drive. the only change you can make is high or low range and this is handled through the gear shift selection.

Feb 13, 2014 | 1999 Land Rover Range Rover

2 Answers

I was driving my97 rangerover and came to a stop light and upon leaving thestop it wouldnt move dash computer says transfer case in neuteral i tried to put it in park and it made a sound as if it was not...


Hello Joey... Have you ever put your Rover into Low range? You might have accidentally bumped the shifter to the right and it started to select Low range, but it is in Neutral because the Low shift was interrupted. To correct this, with the engine off, but with the key on, select Neutral first. Then start selecting Low by putting pressure on the shifter towards the right(to engage low, the second set of gear/numbers). Keep pressure on the shifter until the dash shows a Low range light and is no longer beeping...now you are in Low Range. Next try to select High range by putting slight leftward pressure on the shifter. Keep pressure on it toward the left until it quits beeping and no longer has any gearbox, neutral, or low range lights (20-30 secs Max each way/Range, etc.) Then select park and try restarting the engine, if you hear any funky/grinding sounds shut it down and repeat above process. It should work on the first try, however, You may Try it a few times before giving up on it if you never use low range. The Low range shift solenoid is probably shot if you cannot get it back into High Range, etc. Good Luck, Brian

Jan 17, 2012 | 1997 Land Rover Range Rover

1 Answer

Hi, My 02 Range Rover has a warnig light showing trans safe mode. I put it into low range with no problem drove for a couple of miles and tried to put it back into high, with no joy. It is driving ok and...


these rovers are made like a big computer...if theres is anything wrong with the transmission it will put itself into "safe mode" so it wont rev high and basically you cant go very fast. so you could have a stripped gear, low fluid, or even the gears could be too close or too far apart.

Dec 21, 2010 | Land Rover Range Rover Cars & Trucks

1 Answer

When I try to shift from low transmission to high transmission, it won't work, the light keeps beaming and there is still a beeping sound, and if I shift the gear it appears the code to "put it in...


To change from low to high or vice verse, the transmission should be in neutral - that's what the Message Centre is telling you to do. It's also recommended you do this while stopped.

Aug 05, 2017 | 1996 Land Rover Range Rover

1 Answer

2003 range rover power door locks do not work


does the roof lamp work? if not then means your Vehicle in transport mode. to have it in normal mode you need to take it to a dealer or something equivalent to have the job done by approved diag. machine

May 19, 2010 | 2004 Land Rover Range Rover

1 Answer

Air suspension out (inactive ) code



1. The automatic suspension system on a Land Rover must be placed in a service mode (High Lock) prior to raising the vehicle on a frame-contact hoist. This can only be accomplished by using a Land Rover Test Book Scan tool or an aftermarket equivalent.

2. If the suspension is allowed to hang freely at maximum extension, the suspension controller will enter a fault lockout mode and disable the compressor and height sensors

3. In addition, the suspension system will vent the suspension in an attempt to bring the vehicle to a correct ride height.

4. Since the suspension is hanging free at maximum extension, all the air will be vented, causing the vehicle to sit at maximum low when taken off the frame-contact hoist. A Land Rover Test Book Scan Tool or an equivalent is required to reset the suspension once it has entered the lockout mode.

Sep 23, 2009 | 2003 Land Rover Range Rover

1 Answer

Beeping from low to high gears in p38 diesel auto


The gearbox selector switch and/or motor located on the rear of transfer case.

long live "the green oval"

Dec 14, 2008 | 2004 Land Rover Range Rover

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rover Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Rob
Rob

Level 2 Expert

64 Answers

Are you a Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...