Question about Mitsubishi Cars & Trucks

Open Question

How to remove a headlight and replace with a new one for a mitsubishi 380 vrx model 2007

Posted by on


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 5081 Answers


First you disconnect the 3 prong electric plug. To disconnect squeeze the side tabs together (hard) and pull away from the bulb, then you can pull off the protective rubber covering, (its a little snug so give it a tug from the 2 tabs on the top and bottom).

Next unscrew the little Phillips head screw to loosen the bracket that clips in the bulb (take note of how the clip is installed before you remove it, it holds the bulb securely in place).
Just loosen the screw as you do not need to remove it all the way. Pull out the old bulb and replace it with the new one.

The bulb has 3 spacing tabs on it so it can only go in one way. Make note of this when you remove it so you may replace it the same way. follow the steps in reverse and your done.
Note: The little wire clip that holds the bulb in can be a pain. Make sure you get a really good look at it, since it pops out as soon as you loosen the screw. If you get lost, you can always look at the other headlight. Oh, and don't do this in the dark.

Posted on Sep 28, 2009

  • 114 Answers

SOURCE: whem starting to drive off

could be something on the body loose or the fan hitting the shroud

Posted on Feb 06, 2011

66 chrgr
  • 1011 Answers

SOURCE: 2007 Mitsubishi 380 thermostat problems

It will run however the car will never go into closed loop.Means it will run rich and gas mileage will suffer also burning out the oxygen sensors prematurely.

Posted on Oct 19, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 2007 Mitsubishi 380 car

Could be a bad tempature sensor but if the guage starts low and increases to hot, I would have it checked.

May 24, 2014 | 2007 Mitsubishi Eclipse

1 Answer

Road noise 2006 Mitsubishi lancer vrx

I bought a Lancer VRX last month and it got a clunk sound from the front end as u turn or reverse 4/5 times from the drive way. I wrote a email no reply from Mitsubishi. But i was able to get the car in for a check up today with Preston motors Dandenong. The mechanic went for a test drive with me and he heard it too and i have recorded the sound too. Still not fixed after coming home. Really appointed feel like burning this car down now. After spending so much on a brand new car and time dropping the car off for inspection this is what i get. Any one who is planing to buy a lancer be careful. Id rather go for a toyota I made a bad decision by buying this car. its only down 1200km
I feel like taking the car to the local mechanic and getting it checked.
When i bough the car it came with 2 screws missing as they removed the door panels for tinting. got that fixed. Today i got the 1st free service done but they forgot to reset the service time indicator. Any one else with a vrx having this problem please message me on
so we could look into this matter as a team. They only want our money after that its our problem. I' am so upset right now i don't have the luxury of time to take this brand new car back and forth for problems. Not to mention the amount of road noise. I could have put up with that if not for this suspension issue.

Oct 27, 2013 | Cars & Trucks

1 Answer

Removing 380 rear brake light

The Aussie-built Mitsubishi 380 sedan rear light assemblies are removed as follows:

Remove inside boot (trunk) lining behind the light assembly to expose two 10mm nuts with captive washers and (deeper towards the outside of the vehicleA) two plastic lugs.

Unscrew the two 10mm nuts.
Gently prise the light assembly straight back from the rear of the car. This requires some effort. The plastic lugs remain embedded in the sheet metal while notched mating two steel pins remain attached to the light assembly.

The bulb holders are removed by a partial turn anticlockwise (looking at the holder from the top).

See attached image.

Dec 26, 2012 | Mitsubishi Cars & Trucks

1 Answer

2007 Mitsubishi 380 thermostat problems

It will run however the car will never go into closed loop.Means it will run rich and gas mileage will suffer also burning out the oxygen sensors prematurely.

Oct 19, 2012 | 2007 Mitsubishi Eclipse

1 Answer

Changing headlight bulbs on mitsubishi 380

You either have hands the size of an 8 year old child or you have never done this yourself. There is no way to access the connector and manipulate the connector release tabs to remove the globe on the drivers side with the assembly in place, with all the plumbing and water bottle in place. You have to remove the whole front bumper and associated guards etc etc just to replace a globe. Very poor design.

May 15, 2012 | Mitsubishi Cars & Trucks

1 Answer

MITSUBISHI 380 VRX 2008 How do you remove the headrest

Neither of the answers are actually correct.
Yes you need to press the button PLUS use a number drill or similar in the little hole on the opposite headrest leg @ the same time. The headrest will come out very easily when you do bothe these things @ the same time.

Apr 27, 2012 | Mitsubishi Cars & Trucks

1 Answer

How to r&r headlight switch on 2007 mitsubishi outlander

Remove the clamshell cover from the column (philips screws)

Press together on the top and bottom levers on the headlight switch base and pull outward.

Jul 17, 2009 | 2006 Mitsubishi Outlander

3 Answers


you change the bulb from inside the engine compartment . raise the hood and feel for a plastic retaining ring in the back of the headlite. Loosen 1/4 turn and bulb socket and old bulb will pull out from the headlite assembly Unplug the old bulb and replace with new one . assemble in reverse order.

Nov 02, 2008 | 2004 Mitsubishi Endeavor

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides