Question about Cars & Trucks

Open Question

Value of 1998 Model70-800, Furby with Body: Silver w/ Black spots,Ears:Pink on inner and a Pink tummy? Never been out of the box!!

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Transmission diagram


the tcm is the computer to the transmission and it is that silver looking box on inner passenger fender under the hood.

May 02, 2013 | 1998 Plymouth Grand Voyager

1 Answer

How do I fix the heater switch on a rover 25 1.4i Y reg


** First check the Fuse 19, 20A, in passenger fuse box (see manual- under steering wheel). then earthing connection E5 (Front LH inner wing.
**electricat connections are most accessable at Motor resistor bank, behind glove box (released by 8mm 2 bolts underneath ) Resistor pack in front of blower motor, 2x 6mm bolts. flick or squeese electrical relaese tab**



** Check the state of the motor speed resistor pack/ prone to resistor/resistor wire failure , which is behind the glove box,

The motor circuit is Green, live feed , to motor, slate black to motor speed selector (resistor pack), Output (slate or Yellow or Green or pink And Black) then Heater selector switch to earth (black).
- The feed from the motor is Slate/ Black wire. It pass through (or bypasses) resistor bank which limits the current through) the motor thus controlling. the speed. This has 4 connection slate grey from motor.

**Check 12v feed on blower Motor connector Green +ve , Slate Black to Earth. if ok, short Slate/black(Sl/Blk) to earth motor should run.

-Slate/B black (S/B) via No restor to switch, pos 4,

-Yellow/ Black (Y/B) via High resistor to Switch Pos 3
--Green/ Black (G/B) via Medium resistor to Switch Pos 2.
--Pink/ Black (K/B) via Xresistor to Switch Pos x.


From heater selector all final connection to earth are via to Black wire to earth on ineer LH inner wing.

Jan 17, 2012 | 2004 Rover 25 1.4

1 Answer

Where is the intake idle sensor located on a 1998 chevy malibu v6


intake air sensor? there is a air sensor on the air cleaner box, there is a mass airflow sensor on the rubber hose to the throttle body, there is a idle air control on the throttle body that looks like a little black motor,

Sep 23, 2011 | 1998 Chevrolet Malibu

1 Answer

The fuel pump don't get electric power, I follow the positive fuel pump supply wire and localized it going in a electric black box just above the cooler radiator, and the line (pink with a black...


RESET THE INERTIA SWITCH LOCATED ON THE HINGE SUPPORT BEHIND THE LEFT INNER WHEEL HOUSE IN THE TRUNK AREA.FORD TAURUS STATION WAGON LOOK LOWER CORNER PILLAR REINFORCEMENT.RESET INERTIA SWITCH SEE IF FUEL PUMP WORKS.IF SO SWITCH COULD BE BAD TRIPPING OFF THE FUEL PUMP.

Jun 19, 2011 | 1987 Ford Taurus

2 Answers

What fuse amp and what fuse number go to 1998 vw passat v6 Into the cigarettes lighter and the one in the trunk All 12 volt spots


For 1998 VW Passat V6 the fuse box is located on the left side of dashboard behind a plastic cover (for left hand steering wheel vehicle). On inner face of the plastic cover you will find the fuse diagram.
The cigarette lighter fuse for 1998 VW Passat V6 is placed in the fuse box / relay plate fascia 1, (driver's door open). See pictures below:

tdisline_149.jpg

The fuse box / relay plate fascia 1 diagram:

tdisline_150.jpg
Fuse no.# 33 - F33 (15 Amp.) = Cigarette lighter


Please do rate my response. Thanks!

Jan 07, 2011 | 1998 Volkswagen Passat

1 Answer

Where is the body control module located in a 2001 grand caravan


Not sure if this is a 98 Plymouth Grand Voyager or a 2001 Grand Caravan, but in either case:
The Body Control Module (BCM) is located under the Dash on the left side, behind the parking brake, mounted on the fire wall, to the left of the steering column. It is attached to / underneath the Junction Box. The BCM is the silver metal box attached to the black portion which is the Junction Box.
Let me know if this helped, or if you have additional questions or information. Feel free to contact me at FixYa.com!

Jan 15, 2010 | 1998 Plymouth Grand Voyager

1 Answer

Drives fine and then won't start or stalls.


remove the cover from around the fuse box under the hood on the drivers side then try moving the wires around from the main fuse box where it runs down from the box to the top of the transmission, have somebody try to start the car while you are doing this and see if it starts up there is a splice that likes to get hot and quit working in the pink or red wire that powers a portion of the fuse box including the fuel pump fuse. look for a brown spot in the wire, if you can make it start by moving these wires around cut the brown spot out and re-splice them together using a **** connector. seen it a thousand times....

Dec 11, 2009 | 1996 Cadillac Seville CA Value

1 Answer

I'm having trouble installing a radio in my 1992 toyota celica


go to any auto parts store and ask for a 12 volt test light, it has a bulb inside and a pointed end like an ice pick, u attach one end to a good ground and then probe wires for power, when u have a hot wire with 12 volts the light in the handle will shine on. They cost about $6.00 at Kragen I think.

May 12, 2009 | 1992 Toyota Celica

1 Answer

Replace rotor


when you take the front wheels off you will see a silver center cap in the middle of the hub take a flat heat screw driver a gently pry the cap off (don't worry if you mame it alittle) there will be a cotter pin a nut and a washer then you outter bering take them all off then the rotor will come off the inner bering is still in the rotor being held by the grease seal pry the old grease seal off and remove the bering. check berings for wear like ruff spots. make sure you buy a new grease seal for the rotor. reverse removal procedure re pack berings with fresh grease inner first place bering in the rotor put seal in place will need to tap it in carefully when putting the nut back on tighten untill snug not tight check for specs if you want i usually make it snug then 1 more turn do not over tighten and you will be good

Apr 07, 2009 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...