Question about Cars & Trucks

Open Question

Belts for 2013 Zee2 2348 Dixie chopper - Cars & Trucks

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1373 Answers

SOURCE: Reverse on my Dixie chopper zee1 won't go in reverse

it could be jammed, which could prevent it from shifting your vehicle into reverse. Look for any dirt, debris or sticky residue near the "reverse" setting, and carefully clean it out.
A vehicle that won't go in reverse is often an indication of a transmission problem, and transmission repair can be rather expensive. If you would like to try a more affordable possibility before assuming that there is something seriously wrong with your car, then you should check your vehicle's transmission fluid levels. This should be done while your vehicle is running and in park or neutral, and you should simply remove the dipstick, clean it with a clean rag, reinsert it and check the fill line on the dipstick. If you find that your transmission fluid is low, try topping it off - you might just find that your vehicle will reverse perfectly if you do.
Or you could have major transmission have serious transmission problems that will need to be repaired by a professional transmission repair shop.

Posted on Jun 02, 2016

  • 41478 Answers

SOURCE: My Dixie chopper classic 2750 won't crank it turns on but it won't turn over it just makes the beeping noise. What's the problem?

start by looking at the starter or solenoid .then safety circuit could be you forgot the PTO button

Posted on Aug 20, 2016

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a replacement dixie chopper roll bar pin


Sorry we do not sell parts here nor do we have any way to locate them for you. Sorry.

Jun 29, 2017 | Cars & Trucks

1 Answer

I ran my dixie chopper out of gas , now it won't start. Any suggestions?


Take the air cleaner off an pour a very little bit of gas into the carb and it will help prime the system and get the gas pumping again.

May 21, 2017 | Cars & Trucks

1 Answer

I need to know the socket size to fit the lug nuts on a Dixie chopper magnum225023 x 10150-12


We don't know what size. So how about try all socket that you have. Or measure the nut and go buy it.


Good luck

Mai

May 16, 2017 | Cars & Trucks

1 Answer

Dixie Chopper zero turn mower will not start.


check or by pass the parking brake sw. it is on the same circuit.

May 13, 2017 | Seat Cars & Trucks

1 Answer

How do I change hour tracker on a Dixie Chopper 2250 Magnum?


You dont. That would be the same as resetting the odometer on a car.

Nov 01, 2016 | Cars & Trucks

2 Answers

My Dixie chopper classic 2750 won't crank it turns on but it won't turn over it just makes the beeping noise. What's the problem?


Wrong site. I tend to fix mowers, but they have to be with me. 2 or 3 a year compared to 300 cars I do a year.

Aug 20, 2016 | Cars & Trucks

1 Answer

I have a 23hp Kohler on a Dixie Chopper motor has about a 1000 hours on it runs good until it warms up then starts to run rich and has no power. If I pinch the fuel line it starts to run good.


Sounds like your fuel shut off solenoid isn't doing its job. I'd replace that first then adjust the choke if it's still not running right.

Apr 26, 2016 | Cars & Trucks

1 Answer

2703 Dixie chopper with 27hp generac. This spring I went through and changed all my fluids and filters, air filter and spark plugs. This is a thing I do at the start of every year. Back in may I had to...


Check the gap between the coils and the flywheel. It should be a gap of 2 Buisness cards. They might have moved a little bit. Try this first. The magnet that the flywheel travels around creates the charge for the charging system. Two unrelated problems

Aug 19, 2012 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...