Question about Cars & Trucks

Open Question

Clutch sticking to floor board after a while driving all levels full and no leaks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: sticky clutch

slave cyl is sepreate from master cyl you have air in the clutch hydraulic system replace slave and inspect clutch master for leaks on drivers floor board area pull carpet back and make sure to bleed system properly!!!!!!!

Posted on Feb 26, 2009

  • 295 Answers

SOURCE: 1979 Datsun 280zx clutch problem

Well, Your are going to have to put a few bucks into a new clutch , disc, pressue plate.
A local transmission shop should be able to help you out.

Posted on Mar 15, 2009

  • 8 Answers

SOURCE: 1990 Mazda B2200 PU. Clutch sticks to the floor

I just had the same problem today it was the master cyclinder
its a common mazda problem

Posted on May 10, 2009

  • 3600 Answers

SOURCE: Nubira 2000 model sticky clutch.

Regards Darryl, you have a leak try bleeding the system then lube the contact ball which you should of done when replacing the slave, also could have master going out happens all the time weakest point in the system is the first to go out.

Posted on Jul 01, 2009

vis_184
  • 27 Answers

SOURCE: NEED HELP WITH FIXING MY WIFES CLUTCH ON HER TRUCK

If it is a hydraulic clutch, find the reservoir and top it up with fluid and then you will have to find the bleeder screw and bleed the clutch. It is the same process as bleeding brakes. Not sure on these vehicles where the bleed screw is but in most cases it is on the transmission. It can be easily found if you follow the line from the clutch master cylinder to the transmission it should be close to where the line goes into the transmission.

Posted on Jan 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Sonata, Clutch sticks when weather is hot


Check your fluid level 1st incase you have a leaking slave cylinder. It sound like there is air in the line presumeing it is hydraulic & not cable operated. Bleed the clutch.

Jun 27, 2012 | Hyundai Motor 2004 Sonata

1 Answer

The clutch in my 1993 mazda b2200 keeps sticking to the floor


Could be a leak in the hydraulic system, check all hoses, master/slave cylinders for leaks

Jun 11, 2012 | Mazda Cars & Trucks

1 Answer

2001 prado. clutch pedal sticks to floor under pressure, l can lift it with my foot and carry on driving. Pedal often sinks to the floor on its own. Slave cylinder issue?


may have a large leak in the slave cylinder. do you see fluid dripping underneath te transmission housing? it could have an internal leak but not as common. check the fluid level in the little reservour on the firewall.

May 26, 2011 | Toyota Land Cruiser Cars & Trucks

1 Answer

My daughter's 1997 Camry V-6 - Clutch pedal will go to the floor and sometimes won't come back. Checked fluid in clutch reservoir - OK. No fluid leaking. Had her press the clutch pedal and everything...


try bleeding the clutch slave cylinder its just like bleeding brakes just follow the line from the clutch master cylinder where you checked the fluid to the slave cylinder and pump the clutch three times and hold it to the floor while someone loosens the relief valve you repeat until no air comes out and it is all fluid then you check you fluid level again to make sure it is full then if the problem continues it might be time for a clutch replacement

Oct 20, 2010 | Toyota Camry Cars & Trucks

1 Answer

My clutch pedal went to the floor in my 2003 chevy cavalier


check the clutch fluid level. if its empty, you have a leak, and you have air in the system. if there is no leak, and the fluid level is full, the problem lies in either the clutch master cylinder or slave cylinder.

Mar 23, 2010 | 2003 Chevrolet Cavalier

1 Answer

Clutch sticks when pushed to floor


a clutch pedal that doesn't return back to you is sometimes a symptom of a failing clutch slave or general fluid leak. This is of course referring to a hydraulic clutch. If your fluid gets too low or there is an air leak your pedal will stick to the floor and not return.

Oct 26, 2009 | 1994 BMW 3 Series

1 Answer

Nubira 2000 model sticky clutch.


Regards Darryl, you have a leak try bleeding the system then lube the contact ball which you should of done when replacing the slave, also could have master going out happens all the time weakest point in the system is the first to go out.

Jul 01, 2009 | 2000 Daewoo Nubira

1 Answer

1979 Datsun 280zx clutch problem


Well, Your are going to have to put a few bucks into a new clutch , disc, pressue plate.
A local transmission shop should be able to help you out.

Mar 15, 2009 | 1997 Chevrolet Cavalier

1 Answer

Sticky clutch


slave cyl is sepreate from master cyl you have air in the clutch hydraulic system replace slave and inspect clutch master for leaks on drivers floor board area pull carpet back and make sure to bleed system properly!!!!!!!

Feb 26, 2009 | 1992 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...