Question about Cars & Trucks

Open Question

Need to replace hub with seal kit and bearings. Also the belt.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
keemo68
  • 1263 Answers

SOURCE: 2002 Mazda Protege 5 Hub Bearing Replacement

which hub the rear or front?

Posted on Sep 01, 2008

Ad
  • 1 Answer

SOURCE: Torque specs for front wheel hub nut

112 to 174 ft lbs

Posted on Apr 04, 2009

  • 186 Answers

SOURCE: NEED TO REPLACE WHEEL HUB BEARING OR ONLY THE BEARING

Front Is pressed into hub & knuckle.Rear is a Hub/Bearing Assembly held in by 4 10mm bolts.Will need to pound out with hammer in rear after bolts come out,lots of rust holding them in.Front Knuckle has to come off,Then a large Snap ring,then press out the hub,then the wheel bearing.Hope this helps

Posted on May 19, 2009

defadad
  • 351 Answers

SOURCE: need instruction manual/schematics for replacing 2005 kia rio driver side rear wheel bearing. i've got the wheel/hub/bearing off, not the inside ring to the bearing. i need to know how to replace it .

clean all the grease if there is any out of the hub, turn the hub over and using a drift and hammer strike the shell from the back edge working around the shell as you go, should not take too much to remove it but you will need a bit more than a tap with the hammer.
Hope this has helped you

Posted on May 22, 2009

sup_air
  • 1 Answer

SOURCE: Torque Specs to replace front wheel bearing hub in a 2006 Equinox

He talk about 2006 Equinox,= SKF spec = 151 ft

Posted on Jan 09, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace front hub assembly 2002 Suzuki XL7


the front wheel bearing hub?
XL-7 (the dash matters)
my wild guess, is the questions was
what are all steps to do this job. and tools.
that?
RTM?

https://suzukipitstopplus.com/Products/10056-2002-grand-vitara-xl-7-service-manual.aspx

http://www.fixkick.com/hubs/FW_BEARINGS.html#newer
the link shows all years, and variances.

here is a photo review, that is accurate up to
1998, and beyond , if you skip the bearing service parts. as yours are INTEGRATED
and NON-serviceable.
http://www.fixkick.com/hubs/FW_BEARINGS.html


the photo 6a and B
shows removing the hub,
so do that , buy a new hub and put it back
the same way, using the tool stated
at the stated ranges of torque
123-180 ft/lbs.
this range allows you to get the screws into the locking rings.

Dec 11, 2016 | 2002 Suzuki XL-7

1 Answer

I'm having trouble replacing my belt on my 94 gmc 1500 the air compressor went out now I need to find out what belt I need to by pass it


Is the belt a V-Belt?

If so- then you have bolts you can loosen to
move the compressor or other accessories

If it is a single serpentine belt, I don't see the problem

If the compressor hub or pulley still turns, you leave the
compressor there & just have no a/c

The truck is too old to be spending money with bypass
kits & such, for no reason.

If the clutch hub has a locked up bearing, replace it, if the a/c
would still work?

Jul 16, 2014 | Cars & Trucks

2 Answers

Bad front wheel bearings


I have a 95 Prizm and replaced my bearings. the front wheel bearings are a real pain and requires a press.

loosen the half shaft nut. jack the car up and secure with jack stand, take the wheel off, remove the nut on the half shaft, disconnect the strut from the hub, disconnect the lower ball joint, disconnect the tie rod end (i use a pitman arm puller), you should now be able to remove the hub. unless you have a press and press skills take the hub and new bearing kit to a machine shop with a press and make sure they install the new seals and retaining clip on back side of hub. when installing hub with new bearing make sure you use the right torque specs..

alternate idea, pull the hubs from a junk yard and replace bearings on these, install on your vehicle it minimizes vehicle down time

final thoughts, use penetrating oil on all fasteners days before starting work and day of work. might be a good time to replace lower ball joins

Oct 10, 2013 | 1994 Geo Prizm

1 Answer

What is the foot pounds for the front wheel bearings on a 1995 chrysler cirrus


Hello, If you Chrysler has replaceable wheel bearings and seal. This is the way it goes---pack the wheel bearing with new grease-install the bearing in the wheel nub--install new back wheel seal--coat the axle shaft with grease lightly, thing coat-----install wheel hub on to axle shaft...be careful here don't damage the rear hub seal------------insert front race washer---install axle shaft nut--tighten nut down wheel nut until it is firm with water pump pliers----spin the hub/with tire mounted.
(the wheel and hub will turn but not freely)----take the pliers and back off the axle nut 1/4 turn----now spin the wheel and axle hub, it should spin freely---now if doesn't spin freely---back off the axle nut about 1/16 or 1/32 (or just a little bit)-----now, spin the wheel and hub and if turn freely------------Now grab the top of the wheel/tire and move it back and forth.-----if there is some movement ---try tighten the axle nut just a little little bit, unit the one can barely feel some little movement in the wheel/tire and hub.-----------Now, spin the wheel/tire and hub and it should also turn freely.

If it does----install new and correct size of cotter pin and bent the ends around the axle nut.----

coat the inside of the hub cup with grease. Now, use an rubber or plastic hammer to install the cup on the wheel/tire hub. You are finished with one wheel bearing maintenance. Now do the other side.



I really don't know if you Chrysler Cirrus has replaceable wheel bearing. All the auto/trucks have replaceable hubs, that means that the replacement is total hub with axle shaft, sealed bearings, and seals. This is bolt to each wheel steering hub. This work to remove these one unit hubs.

Four bolts hold the axle hub to the steering hub. Hear is the problem!! it has rusted to the steering hub. Also, these hubs cost more than replacing bearings, races, seals to cool turn of $180 to $250+ I wish you luck in your replacement of wheel bearing on your Chrysler. GB..stewbison

Sep 24, 2011 | Chrysler Cirrus Cars & Trucks

1 Answer

The rear wheel bearings on my 1998 Honda Civic Aerodeck are rumbling and I need to know how to replace them or regrease and is it a DIY or garage job


Your vehicle is equipped with sealed bearings that are pressed into the hub assembly. If your rear wheel bearings are making noise, you must replace the entire bearing and hub assembly (they cannot be greased).

To replace it, raise and support the vehicle and remove the tire and wheel assembly. Remove the brake drum. Remove the bearing cap, the spring nut and the axle washer. Remove the hub assembly and hub seal. The new hub assembly should come with a new hub seal installed. (See first picture below)

TIP: The brake drum has threaded holes in its face where an 8mm bolt can be inserted to help "push" the drum off of the hub assembly - they can get really stuck. (See second picture below)


dttech_22.jpg


dttech_90.gif

May 22, 2011 | Honda Civic Cars & Trucks

1 Answer

How do i replace bad front wheel bearing ?


Replace the hub assembly which can be bought for $58 to $100 from various sources.

REMOVAL AND INSTALLATION
  1. Raise and safely support the vehicle.
  2. Place jackstands under the cradle and lower the vehicle slightly so the weight of the vehicle rests on the jackstands and not on the control arms.
  3. Remove the wheel assembly.
  4. Insert a drift punch into the rotor and remove the hub nut/washer.
  5. Remove the brake caliper, support and the rotor.
  6. Using the front hub spindle remover tool, separate the halfshaft from the hub.
  7. Remove the hub/bearing assembly-to-steering knuckle bolts and the hub/bearing assembly. To install:
  8. If replacing the seal, drive the seal towards the engine. Cut the seal off the halfshaft; be careful not to damage the halfshaft boot. NOTE: If the speed sensor bracket is removed or loosened from the steering knuckle, the speed sensor gap must be adjusted. If the speed sensor is removed from the bracket, speed sensor wax must be applied to the sensor before it is reinstalled in the bracket. Failure to apply the wax will permit corrosion and may result in sensor failure.
  9. To install the new grease seal, lubricate the with wheel bearing grease and using the hub seal installer tool, install the seal.
  10. Install the hub/bearing assembly-to-steering knuckle bolts and the hub/bearing assembly. Tighten the hub/bearing assembly-to-steering knuckle bolts to 70 ft. lbs. (95 Nm).
  11. Install the halfshaft to the hub.
  12. Install the rotor and caliper.
  13. Install the hub nut and washer. Tighten to 183 ft. lbs. (245 Nm).
  14. Install the wheel assembly.
  15. Remove the jackstands and lower the vehicle.
prev.gif next.gif

Jul 03, 2010 | 1996 Cadillac DeVille

1 Answer

2wd front wheel need to replace bearings or hub assembly which is best


A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

Apr 09, 2010 | 2003 Ford Explorer Sport Trac

2 Answers

Need to replace wheel bearing hub kit on 2000 s-10 2wd. is it a kit or just a bearing? What are the steps?


The bearing is "pressed" into the hub/spindle. On the 4x4 model the wheel hub is bolted onto the spindle from the back (remove wheel, caliper and bracket, axle nut, 3 bolts on the back and tap out). On the 2 wd model, It'll have to be pressed out, and back in. Remove the wheel, caliper and bracket. Follow the ABS sensor wire to the inner frame rail in the engine compartment and unplug it (along with removing the bolted clip on the upper "A" frame). Separate the tie rod end, upper and lower ball joints (won't affect the alignment) and remove the spindle. If you can locate a used one you can have it ready to put back in immediately.

Feb 25, 2010 | 2000 Chevrolet S-10

2 Answers

Need to know how to install wheel bearings on a chevy cavalier


1) Break the torque on the center wheel nut and remove the nut and washer before jacking up the front end. 2) Jack up the front and remove the tire. 3) Remove the brake caliper and rotor. 4) After removing the rotor you will see the bearing assy. There are 3 torx bolts holding it on. You need to put the transmission in neutral to turn the hub and line up the hole to remove the bolts. 4) Knock it loose with a hammer and install in reverse order. The kit comes with a seal but I don't believe it's needed on a 96. Pretty simple job really... Good Luck.

Feb 19, 2010 | 1996 Chevrolet Cavalier

1 Answer

Need help replacing front hub


Here's the steps....getting some pics for you....hang on a minute or two.

Front Hub Removal & Installation To Remove:
  1. Remove steering knuckle.
  2. Using a suitable slap hammer, remove wheel hub assembly.
  3. Using a suitable bearing press, remove outer bearing, oil seal, outer bearing race and preload spacer.
  4. Remove inner oil seal, inner wheel bearing and inner bearing race.
NOTE: It is not necessary to remove dust cover (back plate).
To Install:
  1. Using a suitable bearing press, install bearing races in steering knuckle.
  2. Pack the bearings and hub area with lithium grease.
  3. Install inner bearing in steering knuckle.
  4. Lubricate lip of NEW inner seal and press seal into knuckle.
  5. Install preload spacer into bore.
  6. Install outer bearing into bore.
  7. Lubricate lip of NEW outer seal and press seal into knuckle.
  8. Using an appropriate tool, support inner wheel bearing and press wheel hub into knuckle with a force of 2500kg.
  9. Install NEW inner seal.
  10. Install knuckle assembly.

May 13, 2009 | 2004 Kia Rio

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...