Question about Cars & Trucks

Open Question

Check light comes on while on shore power...goes off after resetting

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a trip-pac with espar heater in a 2015 volvo all worked fine until it was plugged into shore power, now it all lights up fan,ac,ht. but when i put it on heat nothing clicks but the ht wvs blnk


THOSE UNIT HAVE A RESET BUTTON ON THEM TRY THAT, BUT THERE MAY BE AN ISSUE WITH THE DRAW TUBE FOR THE FUEL OR FUEL FILTER, OR THE HEATING ELEMENT, MOST LIKELY UN RELATED TO THE SHORE POWER COMPLAINT

Jan 11, 2017 | Volvo Cars & Trucks

1 Answer

Car battery goes dead after a few days of none driving, what's the problem?


Hi,first of all make shore that the battery is checked to make shore there are no dead cells,if ok then you nead to see if there is a drain on the battery,first take the fuse out of the clock,thenundo the earth lead on the battery,get a test screw driver that has a wire with a crockerdial clip on it,put the crockerdial clip on the earth lead and the screw driver on the earth terminal if it lights up then you have a drain on the car, you will then have to take out all the fuses one by one with the screw driver still in place,if the light goes out when you pull one of the fuses out that will be the falt.
I hope this has helped best of luck.

Mar 13, 2014 | 2004 Chrysler Sebring

1 Answer

Need to know how to wire a shore plug that is a 50amp125/250 with a 12/3 wire there is no Indys on this female mount shore power inlet


to start with 12-3 wire is too small for a 50 amp load..but if you are doing 220 it goes like this you have a black ..white and green wire..black is hot..white is hot and green is ground ..if its 110..the black is hot.. white is ground and green is earth ground to casing metal..the bare copper wire is earth ground.. make sure no wires cross.. this will short it all out..

Dec 27, 2013 | Cars & Trucks

3 Answers

Reseting a check engine light after a repair


Sometimes taking off both battery terminals and holding them together for say 5 minutes can help. A diagnostic tool is a more reliable option, bring up the code and erase it. Erasing codes will take off the check engine light. Provided the problem has been eliminated it shouldn't come bacK on.

Sep 09, 2011 | 2006 Land Rover LR3

1 Answer

I changed the oil, spark plugs and valve cover


test to make shore you ignition coil is working" unplug any plug wire and then try starting it...you should her the ticking from the ark of electrisity from the coil to the engine block its self... first: be shore youve connected the spark plug wires in to the right slots on the ignition coil second: make shore the wiring harness just upstream from the air filter is connected"without it my montero want start" third:make shore all harmesses are connected and tight.... forth: now turn the car on..but dont start it.. and see if the check engine light goes off.... fifth:try giving it a lil bet of gas when trying to start..... thats all i can think of, srry for spelling...hope it helps

May 11, 2010 | 1998 Mitsubishi Montero Sport

2 Answers

My check engine light always comes on and its been doing it for awhile now. I tried to get inspection today and it wont passs. Any ideas why it wont go off


have a Scan 4 trouble codes some parts stores can do this free or cheep they also sell inexpensive ones.hope this helps.

Mar 11, 2010 | 2001 Pontiac Grand Am SE

3 Answers

1994 BMW540i Break Light Out indicator reset


If the brake light works, disconnect battery negative with ignition key ON and Radio ON, but engine OFF, four minutes after connect Battery terminal, do not panic if terminal sparks wile connecting, *** it well turn ignition key OFF, than start the motor and verify
if problem remains

Jan 22, 2009 | 1994 BMW 5 Series

2 Answers

How do I reset a check engine light for a 2005 Pontiac Sunbird?


disconn batttery for half an hour ..actually should only take 5 minutes but stay powered down longer...good luck

Dec 16, 2008 | 1992 Pontiac Sunbird

1 Answer

1998 mazda protoge brake lights do not work checked fuse...ok.... changed brake light switch but still no brake light... any suggestions?


stupid question but have you checked that all the globes arnt blown.
also have you adjusted the stop light switch properly.

a good test to to is check your globes replace them if you are not shore of them then un plug the stop light switch and earth out the two pins in the plug then check if the light come on.
if they do you may still have a faulty new switch our it might need adjusting

Dec 05, 2008 | 1998 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...