Question about 2003 Ford Expedition

1 Answer

I lost the bushing on the brake switch for a 2003 ford expedition. after installing a new switch it didn't work. could the missing bushing possibly prevent the switch from working?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Ford Master
  • 946 Answers

YES! You talking about the brake pedal switch? Needs to be attached correctly.Get what you need from FORD parts at a dealer. don-ohio

Posted on Jan 03, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No brake lights on 2000 ford expedition


does it have a trailer connector installed by uhaul or anything if it does possible corrosion in wires or a bad ground at rear of vehicle

Apr 04, 2014 | 2000 Ford Expedition

1 Answer

How to install new brake light switch on 2008 Ford expedition


On the brake pedal arm under the dash there will be a switch with a yellow pin holding it in place. Remove the pin and remove the switch....watch how it comes apart. You have to put the bushings back in the same way. You might have to rewire the connector for the switch due to design change. Good Luck

Nov 13, 2012 | 2008 Ford Expedition

1 Answer

How replaced brake ligth switch on ford expedition 2003


make sure check brake light fuse first if brake light fuse okay.you replace brake light switch by removing trim panel below steering column.look under brake pedal area unplug electrical connector .remove the cotter pin and pull switch and power brake booster pushrod off the pin.then slide switch off power brake booster pushrod dont lose small nylon washer when installing new brake light switch.

Nov 13, 2011 | 2003 Ford Expedition

1 Answer

I need good photos or instructions to change the brake light switch on a 1999 ford expedition


from autozone.com
f43af9d.gif Fig. 2 Brake pedal position switch removal- F-150, F-250, Expedition and Navigator; 1999-00 F-250SD, F-350, and F-Super Duty Models
  1. Disconnect the negative battery cable.
  2. Disconnect the brake pedal position switch.
  3. Remove the self-locking pin.
  4. Remove the brake pedal position switch from the brake master cylinder push rod.
  5. Remove the brake master cylinder push rod spacer.
  6. Remove the brake master cylinder push rod bushing.
  7. The installation is the reverse of the removal.

Sep 24, 2010 | 1999 Ford Expedition

1 Answer

Brake switch location 2003 ford expedition and how to replace it


on brake pedal you unsrecw it and unplug wires then hook the new one up in the same spot

Feb 15, 2010 | 2003 Ford Expedition

1 Answer

How do I install a brake booster on a 2003 Ford Expedition Eddie Bauer with no ESC package? Do I need to bleed anything before removing the part?


disconnect the neg batt cable,loosen clamp and disconnect air cleaner outlet tube and resonator from the air cleaner. 2.disconnect maf sensor connector. 3.lift air cleaner assy from tray and position aside. 4. remove screws from power steering resevoir, and position aside. 5.disconnect brake fluid level sensor, and if equiped brake pressure switch. 6.remove the two mounting nuts holding master cylinder, position master cylinder aside (DO NOT LOOSEN LINES ON MASTER CYL). 7.remove mounting bolts for degas bottle and postion aside. 8.if equiped diconnect wiring at the pedal position sensor. 9.relaease clamp and disconnect hose. 10.remove the pin, washer, bushing and switch, disconnect pushrod. 11.remove the nuts and brake booster, to access nuts fold back sound insulation. reverse procedure to install.

Sep 16, 2009 | 2003 Ford Expedition

1 Answer

My 2003 Ford Expedition continues to sputter, miss


MAF SENSOR NEEDS CK AND OR REPLACE. 1ST SENSOR COMING OUT OF AIR FILTER

Jun 14, 2009 | 2003 Ford Expedition

2 Answers

2003 expedition cruise control not working


I just fixed my Cruise control problem. It didn't work at all, no light in the dash either. What had happened was, I had changed the brake booster some months back and when the brake pedal is disconnected from the booster shaft, it allows the pedal to raise too high. It will contact the cruise control disconnect switch to the left of the brake switch. To find the switch, look close and there is a "L" bracket welded on the brake pedal and the cruise switch contacts this bracket. Well this switch is a self-adjusting switch designed to be installed with the pedal at least an inch or so depressed. When the pedal is released it will contact the switch and push the shaft into the switch to the determined setting and it will lock into that position. I was able to pull the shaft out enough to make contact again and it self adjusted like it's supposed to and now the system works great! What made me go to this switch was by checking power at pin 6 (blk/yellow wire) at the cruise servo connection. This connection has 6 pins and the end pins (1 & 6) both have 12 volts. Mine had no power at pin six, which means the cruise deactivation switch is the problem. Older Expeditions had this switch on the brake master cylinder (recall for fires, etc), but 2003 and up has it on the brake pedal itself. Once I figured out where the switch actually was, it was easy to figure out. If you have done any work around teh brake pedal and disconnected it for any reason, you gotta check this out.

Apr 09, 2009 | 2003 Ford Expedition

1 Answer

FORD BRAKE LIGHT


check the connector at the brake switch located on the brake pedal lever arm if it is ok it is most likely a faulty switch

Dec 01, 2008 | 2003 Ford Expedition

Not finding what you are looking for?
2003 Ford Expedition Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...