Question about Ford Cars & Trucks

1 Answer

2000 Ford mustang 3.8 cranks won't start diagnostic gives code b1353

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 11,723 Answers

B1353 Ignition Key-In Circuit Open GEM Go to Pinpoint Test B .
PINPOINT TEST B: THE KEY-IN-IGNITION CHIME DOES NOT OPERATE CORRECTLY
Do you know what the GEM - genaric electronic control is ?
You need a scan tool to check ignition switch position .Don't know if this would cause a no start . Have you check for ignition spark and fuel pressure ? Are there anyother problems with power door locks or windows or lighting ? Thing's the GEM controls ?
CONDITIONS DETAILS/RESULTS/ACTIONS B1 CHECK IGNITION STATES
NGS
Monitor the GEM PIDS IGN_KEY, IGN_A, IGN_S, and IGN_R while cycling the ignition switch through the OFF, ACC, RUN, START and key out positions.

  • Do the PID values agree with the ignition switch states?
Yes GO to B2 .

No GO to B4 . B2 CHECK GEM INTERNAL TONE OPERATION Trigger the GEM Active Command CHIME ON and OFF.
  • Does the chime operate correctly?
Yes GO to B3 .

No INSTALL a new GEM. For additional information, REFER to Section 419-10 . REPEAT the self test. CLEAR the DTCs. B3 CHECK GEM INPUT FROM DOOR AJAR CIRCUIT Monitor the GEM PID D_DR_SW, while opening and closing the driver door.
  • Do the GEM PID D_DR_SW values indicate CLOSED and AJAR correctly?
Yes INSTALL a new GEM. For additional information, REFER to Section 419-10 . REPEAT the self test. CLEAR the DTCs.

No GO to Pinpoint Test D . B4 CHECK GEM INPUT VOLTAGE FROM IGNITION SWITCH AT CJB FUSE 28 (15A)
CJB Fuse 28 (15A)
Measure the voltage between CJB Fuse 28 (15A), Pin 1, harness side and ground while cycling the ignition switch through all positions.
  • Is the voltage greater than 10 volts in the RUN and START positions only?
Yes GO to B5 .

No REPAIR the CJB. REPEAT the self test. CLEAR the DTCs. B5 CHECK GEM INPUT VOLTAGE FROM IGNITION SWITCH AT CJB FUSE 32 (15A)
CJB Fuse 32 (15A)
Measure the voltage between CJB Fuse 32 (15A), Pin 1, harness side and ground while cycling the ignition switch through all positions.
  • Is the voltage greater than 10 volts in the RUN and ACC positions only?
Yes GO to B6 .

No REPAIR the CJB. REPEAT the self test. CLEAR the DTCs. B6 CHECK GEM VOLTAGE INPUT CIRCUITS FOR OPEN - IGNITION SWITCH CIRCUIT 911 (WH/LG)
CJB Fuse 28 (15A)

GEM C352
Insert ignition key. Measure the resistance between GEM C352 Pin 8, Circuit 911 (WH/LG), harness side and CJB Fuse 28 (15A) Pin 2, Circuit 911 (WH/LG), harness side.
  • Is the resistance less than 5 ohms?
Yes GO to B7 .

No REPAIR Circuit 911 (WH/LG). REPEAT the self test. CLEAR the DTCs. B7 CHECK GEM VOLTAGE INPUT CIRCUITS FOR OPEN - IGNITION SWITCH CIRCUIT 1002 (BK/PK) Measure the resistance between GEM C352 Pin 22, Circuit 1002 (BK/PK), harness side and CJB Fuse 32 (15A), Pin 2, Circuit 1002 (BK/PK), harness side.
  • Is the resistance less than 5 ohms?
Yes GO to B8 .

No REPAIR Circuit 1002 (BK/PK). REPEAT the self test. CLEAR the DTCs. B8 CHECK GEM INPUT CIRCUIT FOR OPEN - KEY-IN-IGNITION SWITCH CIRCUIT 158 (BK/PK) Measure the resistance between GEM C352 Pin 9, Circuit 158 (BK/PK), harness side and ground.
  • Is the resistance less than 5 ohms?
Yes GO to B9 .

No REPAIR Circuit 158 (BK/PK) and key-in-ignition switch for failure. For additional information, REFER to Switch-Key-In-Ignition Warning . REPEAT the self test. CLEAR the DTCs. B9 CHECK GEM VOLTAGE INPUT CIRCUITS FOR SHORT TO POWER - IGNITION SWITCH CIRCUITS 911 (WH/LG), AND 1002 (BK/PK)
CJB Fuse 28 (15A)

CJB Fuse 32 (15A)

GEM C352
Remove ignition key. Measure the voltage between GEM C352 Pin 8, Circuit 911 (WH/LG), harness side and ground, and between GEM C352 Pin 22, Circuit 1002 (BK/PK), harness side and ground.
  • Are voltages greater than 10 volts?
Yes REPAIR the circuit in question. REPEAT the self test. CLEAR the DTCs.

No GO to B10 . B10 CHECK GEM INPUT CIRCUIT FOR SHORT TO GROUND -- KEY-IN-IGNITION SWITCH CIRCUIT 158 (BK/PK)
GEM C352
Remove ignition key. Measure the resistance between GEM C352 Pin 9, Circuit 158 (BK/PK), harness side and ground.
  • Is the resistance greater than 10,000 ohms?
Yes INSTALL a new GEM. For additional information, REFER to Section 419-10 . REPEAT the self test. CLEAR the DTCs.

No REPAIR Circuit 158 (BK/PK). REPEAT the self test. CLEAR the

Posted on Jan 03, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
MNfisherman
  • 11896 Answers

SOURCE: my 2000 ford focus cranks, but does not start. I

You will want to find out if you are not getting spark or not getting fuel.
If no fuel, then bad fuel pump, plugged fuel filter, or bad fuel pressure regulator, or bad fuel pump relay.

If no spark, then bad crank sensor, or ignition module, or coil packs.

Posted on Oct 14, 2009

  • 181 Answers

SOURCE: 2001 ford explore sport cranks but will not start.

TUNEUP? WHAT WAS CHANGED?NEED TO CHANGE WIRES,PLUGS CAP&ROTOR ELECTRIC COIL, CHANGE THE FUEL FILTER,IF STILL THE SAME?TAKE OUT THE FUEL FILTER IF WET THEN OK, BUT IF DRY THEN ,FUEL NOT GETTING TO THE ENGINE,CK WIRES TO AND FROM THE PUMP,STILL THE SAME THEN NEW PUMP

Posted on Oct 30, 2009

demonsm
  • 253 Answers

SOURCE: 2000 ford mustang will not start. Cranks but does

Not coil it is fuel pump.

Posted on Dec 11, 2009

  • 1 Answer

SOURCE: I need to know of any transmission changes in the

CABIN NOISE IN 2000 FORD MUSTANG

Posted on May 27, 2010

  • 150 Answers

SOURCE: Cranks strongly, but won't turn over / start.

it might be the fuel pump take the output hose off of it and crank the engine and see if fuel comes out of the pump if it does the fuel pump is not the probelem. if it doesnt come out or if it slowly comes out than you need a new fuel pump

Posted on Dec 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Won t start


use a code reader to reset the CPU. Check the immobiliser is operational

Jan 19, 2014 | 2000 Ford Mustang

1 Answer

2000 ford mustang starts, then sometime won't start


What have you checked so far ?
Spark and fuel ?

Jan 25, 2013 | 2000 Ford Mustang

1 Answer

2009 ford mustang with new battery and good alternator but still won't start intermittently


Do you mean it won't start, or won't crank ?
The charging system would not affect starting.

Dec 06, 2012 | 2009 Ford Mustang

1 Answer

Crank but won't start


You'll have to figure out if it is a fuel or ignition problem.
Is the check engine light on ? Have you checked for trouble codes ?
It could be a relay, the ignition module, coil, fuel pump, or a list of other things.

Jul 09, 2012 | 1995 Ford Mustang GT

1 Answer

2000 ford mustang thetf light flashing not allowing car to start. Checked all fuses. Alarm relay maybe?


There is a small ring around your ignition cylinder. There are 3 wires that run from it. It is some kind of sensor for the Theft or PATS key. If you use your tilt a lot, it seems to have a "undesirable" effect on the small wires...My Mustang Cobra did this one day. Had a great mechanic friend come over to the house...He just moved the column (tilted it about midway). Cranked right up!!! It still does it occasionaly, but all I have to do is move the tilt.

Sep 24, 2011 | 2000 Ford Mustang

2 Answers

My diagnostics port on my 1994 mustang will not communicate with my code reader.


check all ur fuses ! there is one that is blown! it gives power to the diagnostic connector!

Apr 03, 2010 | 1994 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...