Question about Cars & Trucks

Open Question

Wont start installed a new carby kit - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am looking for a carburetor kit for 302V8


you have to be specific as to carby make , model cubic ft capacity etc to get a kit
try e-bay carby kits for the make or find a carby overhaul shop in your area and get the kits from them

Sep 24, 2016 | Cars & Trucks

2 Answers

I have a Strikemaster 2000 ice auger with a Tecumseh engine & carb. I need a carb kit.


If you can ascertain the carb model and make you can usually get the carb kits on ebay for a lot less than you would pay at your local mower repair shop. Check it out.

Feb 25, 2016 | Cars & Trucks

1 Answer

I've rebuit carb.new fuel pump and gas line hose on a 25 horse Johnson.will start but stalls out in a few seconds any ideas why.


adjust the mixture screw either in or out
may have to do this with a few rpms until it settles down
with the carby there are "O" rings and gaskets not shown in the break down that only the service dealers are aware of
My friend found this out after rebuilding his carby and it started and ran but would not develop enough power in gear
In frustration he took it to a service dealer who upon pulling the carby down showed him where the missing "o" rings should have been and explained that the rings are not in the overhaul kit along with some gaskets
after reassembling with the missing parts , the engine performs as new
Knowing that there is a problem I would suggest that you take the carby in to an accredited service center and discuss the problem with them as there is every possibility that although you are doing everything correctly , there may be parts missing that you are not aware of as was the case for my friend

Nov 27, 2015 | Cars & Trucks

1 Answer

1962 Ford Falcon wont run unless choke is partially closed


check the float level setting
it presents as a partially blocked main jet circuit
there could be corrosion in the circuit that the cleaning agent has not removed
it may be necessary to remove the lead blocks for the drillings to physically remove the blockage
if you look at the drillings and passage ways of the carby you will notice what appears to be plugs inserted where it has been necessary to use a drill to make a circuit for the fuel and air flow
these small plugs are lead pellets similar to shot in a shot gun cartridge that are inserted into the hole and pressed to expand and act as a plug
consider taking the carby to an accredited carby overhaul specialist shop where they can remove/ replace these plugs and test the carby on a machine for correct adjustment and settings

Aug 14, 2015 | Ford Cars & Trucks

1 Answer

Looking for a carby diograme for a 18r celica


If they sent you the wrong diagram, then that's probably also the wrong kit - do the gaskets match up?

Worst case, you could use a different carburetor on that car... or if you're ingenious, you could make your own rebuild kit for the carburetor you have.

Aug 05, 2014 | 1977 Toyota Celica 1.8

1 Answer

Tractor starts , but wont run


check float level and operation. check that the idle circuit is clean and if there is a solenoid in the idle circuit ensure that it is working. If the fuel tank is above the carby check for filter / line blockage and that the tap is turning on. as from your description the is insufficient fuel getting to the carby and the bowl is running dry

Jan 26, 2014 | Cars & Trucks

2 Answers

Eninge wont start unless petrol is tipped down carby. carby is a rochester quadrajet with auto choke .


might have to put a carby kit through it, the jets might be blocked thats what it sounds like. when you poor it in the fuel and air gets in straight away but if the jets are blocked you wont get the fuel through. try carby cleaner, use the accelrator cable on the side of the carby to rev it right up while spraying in carby cleaner car will try die out then let off the accelerator. basically you have to clean your carby out

Jun 21, 2010 | 1983 Chevrolet Camaro

2 Answers

My truck runs for 10 sec. then shuts down


if it is a carby model you are looking at a rebuild kit, the problem is the needle and seat in the carby, i would install a needle and seat (complete carby kit if you have the time and the money) then to guarantee the job done i would install electric fuel pump if it does not alreaddy have one, this should fix the problem, hope i have helped

May 16, 2009 | 1989 Dodge Dakota 2WD

1 Answer

How do u set the carb on a 86 mazda sl auto


the flat spot and hard starting is caused from a faulty accelrator pump or a blocked discharge jet in the pump circuit i would be putting a kit in the carby to improve mpg

the only adjustments on the carby is idle speed and idle mixture which dont affect cars mpg

Dec 29, 2008 | 1987 Mazda 323 4-Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...