Question about Cars & Trucks

Open Question

Control board kitchenaid ksrs25

I need to replace

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 ford freestar their is no blower operation resistor board is okay replaced blower


you may have to have the GEM module checked out as I believe it controls heater control operation.

Aug 29, 2014 | 2007 Ford Freestar Limited Minivan

1 Answer

Wiper motor will not stop


If installed control board was used, it may be defective. Also make sure installed board works with your exact year model.

Apr 03, 2014 | Oldsmobile Silhouette Cars & Trucks

1 Answer

Radio volume control 2002 ford explorer is reversed


This is a common problem that occurs with Ford factory head units. Fortunately, it is repairable for about $30 if you don't mind investing an hour of your time. The display circuit board needs to be replaced. The board had your volume control integrated onto the board. You can purchase a replacement board at: www.oem-auto-accessory.com. Note, I have no affiliation with this company and I'm sure there are others that also sell te same part. This is where I purchased mine so I'm simply referencing at least one place you can source the part.

Jan 24, 2012 | 2002 Ford Explorer

1 Answer

TOYOTA HIGHLANDER A/C CLIMATE CONTROL NOT FUNCTIONING


Based on the limited information provided, it would appear you have a bad climate control control board. This controls all heater/AC functions including climate control. If you're unable to change temperatures and/or fan speeds, the board is most likely bad and needs replacement.

Nov 16, 2011 | 2003 Toyota Highlander

1 Answer

Saab 900 fuel gauge erratic. I measure 5 volts on the sender bus going into the tank. This should be 12 surely. The pump has 12 and works fine. My 9 3has 12 volts to the sender .Is the 900 diferent or am I...


fuel gauge voltage is controlled by the dash board, there is a board on the back of the dash that connects the rev counter the voltage is controlled by this board. you would need to change this board. but to do so you would need to open up the dash board display to get to the board or just replace the dash.

Jul 22, 2017 | 1997 Saab 900

2 Answers

Toyota 04 Highlander Temp Control Problem


Hello. Thank you for requesting me. We have been seeing a large amount of Highlanders with temperature control issues. A replacement control is in the proximity of 900 dollars. After the fifth one sold, and some really unhappy customers, I decided to see what the issue was that was causing the failures. It turns out that the problem is nothing more than a broken wire of two. If you are handy with tools, and can use a soldering gun, you can fix it yourself. The problem with the controls needing replacement is a broken wire or two at the circuit board that controls the temperature (the center knob). This is unfortunately common, albeit an expensive repair. Here is how you can fix it yourself: What you will need: Pencil-type soldering iron, rosin core solder, a Phillips screwdriver, a 10 millimeter socket, extension and ratchet. First, remove the plastic fascia that surrounds the radio/heater-AC control. (Be careful to not crack it when removing it.) Next, remove all of the 10 millimeter bolts that holds the Radio/AC-heater control assembly to the dash panel, and unplug all of the wiring connectors. Next, remove the three control knobs on the Heater/AC control panel, and the silver nuts that holds the controls to the panel. They pull straight off. (Under the center knob, you will probably find a loose nut, this is what caused the wires to break, the control is loose in its holder.). Next, turn the assembly over, with the back facing upwards. You will see a rectangular black box. Remove the screws that hold the black box onto the back side of the front of the control panel. There will be a ribbon-wire connector that will need to be removed from the front panel; be careful when removing the black box?s connection, and take care to not damage the connection ribbon wires. Next, remove the entire circuit board from the panel cover, by removing several Phillips screws, this will allow easier access to the control board that needs the wire(s) soldered. At this point, you have two choices: You can solder the broken wire back onto the control?s board, or, if you desire, you can remove the ribbon wire, and replace it with different wires; personally, I choose this path, and I use telephone wire, three lengths, that I strip and solder to both locations, each of the three on the main board and the other end on the control board. Either way will work, as long as you solder the wires back properly, and avoid any possible shorts by allowing the solder to touch an adjacent lead. Once you have soldered the broken wires from the temperature control board back on to the main circuit board; reassemble the parts and refit it assembly to the dash. Thanks for choosing FixYa for assistance today; I hope that this helps you out, and saves you a bunch of money.

Jun 15, 2010 | 2004 Toyota Highlander

1 Answer

Getz 1.4 remote control expensive to replace


only way pay up and smile ,take it on the chin or buy a 1950s morris minor

Jan 26, 2010 | 2005 Hyundai Accent

1 Answer

My windshield wipers quit working on my 2004 Chevy Silverado. They died rather abruptly, slowing down until they stopped on the low setting. I was able to use them on high for a few days and now they won't...


There was a recall on the control board to the wiper motor a few years ago, Check with the dealer and see if the recall is still active and if not you can fix it if you have a solder gun and some solder. The clip on the board where the wire harness clips on to go bad and needs to be re soldered. If you can not solder you can pick up the board from Auto Zone and the step by step instruction to replacing it. Good luck and hope this helps.

Jun 15, 2009 | 2004 Chevrolet Silverado

1 Answer

Speedo unit died then Fuel gauge went to max


the dash control board is the controler for the boards in the dash, fuel temp etc. inside the dash itself, a board on the rev counter controls voltage to feed the the fuel gauge etc. the back of the speedo burnt,there is the 3 pin voltage control chip on the board. you can replace the boards. you can remove them from another dash and place them into yours but if you say the board burnt out on the speedo . then i would just change the dash as it would be easier as you would need to replace the speedo as well. you will also need to inform dvla that the speedo has been changed as for mots its recorded. or have the speedo rectified to the right mileage. not informing dvla can affect your insurance.

Jun 30, 2017 | 1994 Audi Cabriolet

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...