Question about Cars & Trucks

Open Question

How can I turn off no-tow mode on 2006 Crossfire. If bumper is bumped I must disconnect and reconnect battery cables.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

lazydave
  • 68 Answers

SOURCE: Removed bumper on 2001 JEEP Cherokee

Disconnect both battery cables and touch them together to discharge the system. Then replace the bumper and airbag wire. You can then replace the battery cables and start the car. This will let the computer reset the airbag

Posted on Jun 07, 2009

  • 474 Answers

SOURCE: how do you bump start megane 1.9 dci

if its a standard trans yes. put in second gear with the key on and clutch pushed in, when you reach about 5mph let the clutch out until it starts then place in nuetral with the park brake applied and disconnect from the tow vehicle

Posted on Feb 14, 2010

  • 6982 Answers

SOURCE: 2006 Liberty: My 2006 jeep liberty dies while driving and won't ...

Most common causes of that kind of problem are the fuel pump and the crank sensor. Crank sensor should set a code, pump won't. Less frequent but worth mentioning is the ignition switch. Do some testing using a haynes or chilton manual as a guide,. All you need for that is a digital multi-meter.
Before testing anything, check that all the ground points under the hood are clean and secure. there are more than just the battery to the block...check all the smaller ones as well.

Posted on May 05, 2010

  • 504 Answers

SOURCE: we wrecked our 2005 town

all is ok to reconnnect/ your safe put battery earth on

Posted on Mar 12, 2011

  • 457 Answers

SOURCE: how to remove rear bumper 2006 lr3

open hatch you have retainers on either side around wheel wells you have screws on bottom you have retainers remove all retainers and screws than pull on sides and bumper cover comes off.

Posted on Jul 29, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I tried to change battery alarm and all lights went on. How to install new battery in Nissan xtera 2006?


Disconnect the negative cable first and then the positive cable and remove the battery. The lights/alarm will go out when battery is disconnected and may come back on when reconnected. Use door lock key fob to shut alarm/lights off if they come back on when battery is reconnected

Jul 09, 2015 | 2006 Nissan Xterra

1 Answer

How to remove rear bumper 2006 lr3


open hatch you have retainers on either side around wheel wells you have screws on bottom you have retainers remove all retainers and screws than pull on sides and bumper cover comes off.

Jul 29, 2012 | 2006 Land Rover LR3

1 Answer

I have a 2004 Chrysler Crossfire I cannot get the alarm system to turn off. Towing mode will not disable, every time a door is opened the alarm goes off and the alarm triggers again when I drive. I live...


I have the same problem on my 2004 crossfire :(
the alarm goes off out of the no where, even when i drive, the only way that i way able to turn it off was by taking one of the wires off the battery, then stops for a while but after a couple of day it happends again.
How can i reset the alarm system?

anyone knows?

Sep 18, 2010 | 2004 Chrysler Crossfire

1 Answer

2004 crossfire just dies while driving tow it to dealership and it starts, then drove it for 3 weeks no problem, then went to start it / won't start...had to tow it to the dealership they said it started...


HAVE WATER IN GAS OR PARTIALLY CLOGGED FUEL FILTER.SCAN CAR FOR PCM AND THEFT SECURITY FAULTS.CHECK ALL ELECTRICAL WIRES CONNECTIONS TO IGNITION COILS.CHECK BATTERY CABLES TIGHTNESS AND CHECK ALTERNATOR WIRES MAKE SURE BATTERY IS 12.5 VOLTS.

May 28, 2010 | 2004 Chrysler Crossfire

1 Answer

Insert key, turn to start, dash lights go out, no electrical to anything, Batt indicator illuminated, turn key to off, clicking sound from right side near heater duct, also can hear from outside with hood...


Take a good look at the rear bumper area and wiring around it.

There are recorded cases the bumper bracket is cutting into the fuel pump and fuel level sending unit.


Apr 24, 2010 | 1996 Chevrolet Blazer

1 Answer

How do you bump start megane 1.9 dci new battery but will not turn over . can i tow then bump it?


if its a standard trans yes. put in second gear with the key on and clutch pushed in, when you reach about 5mph let the clutch out until it starts then place in nuetral with the park brake applied and disconnect from the tow vehicle

Feb 14, 2010 | 2005 Renault 181

1 Answer

I want to tow the jeep and need to know thecorrect


Review this information and links:
- Trailer 4 Way System Diagram
- Accesories and Instructions

d456d39.jpg

Instructions
1.) Determine a suitable location for mounting the circuit protected converter in an out of the way spot near the left tail lights in the trunk or on the frame rail, if mounted under the towing vehicle.
2.) Ground the white ground wire by placing the ring terminal under an existing screw attached to a clean metal surface or by drilling another 3/32" hole and using one of the self tapping screws provided.
3.) Disconnect the tow vehicle's negative (-) battery cable.
4.) Cut the in-line fuse holder loop wiring.
5.) Using a ring terminal (3/8 inch for top terminal or 1/2 inch for side terminal), attach an in-line fuse holder (with fuse removed) to the positive (+) terminal of the battery.
6.) Route black 12 gauge wire from the fuse holder to the converter passing under or through the vehicle.
Note: When passing the wire through sheet metal always go through an existing grommet, add a grommet or use silicone rubber to insulate the wire from the hole.
7.) Attach 12 gauge wire to the fuse holder with the yellow **** connector.
8.) Reconnect the tow vehicle (-) negative battery cable. Note: See tow vehicle owners manual for any special battery reconnection and instructions.
9.) Determine if the towing vehicle has a 2 wire or 3 wire system.

2 Wire System
  • Has same bulb for stop and turn signals.
  • Some vehicles have a separate bulb for stoplights but also have a combination bulb for turn and stop. These cars should be wired as 2 wire systems, using the wires going to the common bulbs.
  • Note: Attach the crimp on spade terminal provided to the red stop wire and ground it along with the white wire.

3 Wire System
  • Has amber turn signals, separate.
  • Has separate bulbs for stop and turn signals (both red).
  • Note: Attach red wire to tow vehicles brake light circuit.
10.) Using a circuit tester or volt ohm meter (VOM), determine which wire attached to the left taillight assembly is the left turn wire. Attach the units yellow left turn wire to this wire using one of the blue wire taps provided. Determine which wire is the taillight circuit and attach the module's brown tail / license wire to it with a wire tap. Determine which wire is the stop circuit and attach the module's red stop wire to it with a wire tap (for 3 wire systems only, see step 9).
11.) Route the units green right turn wire to the right side of the vehicle. Determine which wire is the right turn circuit and attach the green wire to it with a wire tap.
12.) Install the fuse into fuse holder and test the installation with a circuit light or trailer.
13.) Secure all loose wiring with cable ties.

Testing Procedure
With the ground wire connected and all of the other circuits attached, attach the ground lead of a circuit tester to the exposed ground terminal of the 4-flat end. Activate the tow vehicle left turn, right turn, tail and stop lights one at a time. Probe the three receptacles of the 4-flat end to confirm proper functions. If testing with a trailer, make the proper connections and do the same test as the circuit tester using the trailer lights. If a function on the trailer lights does not work properly, disconnect the trailer lights, turn functions on vehicle off and recheck function with the unit with a circuit tester. Then check the trailer wiring for potential circuit problems.

I hope help you with this (remember rated this help).

Good luck.

Oct 11, 2009 | 2006 Jeep Wrangler

1 Answer

Removed bumper on 2001 JEEP Cherokee


Disconnect both battery cables and touch them together to discharge the system. Then replace the bumper and airbag wire. You can then replace the battery cables and start the car. This will let the computer reset the airbag

Jun 07, 2009 | 2001 Jeep Cherokee

1 Answer

Front bumper damaged.


It's pretty easy to remove the front bumper.

  1. Remove the plastic "air dam" below the bumper by unscrewing and then popping out the four plastic connectors underneath, then two on the sides.
  2. If you have fog lights, disconnect them by reaching up and behind the bumper.
  3. Using an 18mm socket, remove the nuts that hold the bumper to the frame. They will be located immediately behind the tow hooks, if you have them, or the small bumps where the tow hooks would protrude.
  4. Slide the bumper off.
Here's a link to a writeup for installing an aftermarket bumper, but steps 1-11 explain how to remove the factory one, and it includes pictures.

May 06, 2009 | 2008 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...