Question about Isuzu Cars & Trucks

1 Answer

Where is the CAM Position Sensor found on a 1998 Isuzu AMIGO 4X4, 4 cyc

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 682 Answers

Look along the engine about where the camshaft would be. I should have electrical connector and a bolt that holds it into the head.

Posted on Jan 02, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 8 Answers

SOURCE: thermostat on 1998 Isuzu Amigo

Yes, It's under the intake manifold. The manifold would need to be removed Lower hose from radiator is attached to steel pipe leading to it. It will not be an easy mission,and the new thermostat is rated for I believe 170 degrees. That's not much help to keep the interior warm with a rag top when it's 20 below zero.

You can boost the heating level by adding vinyl cover over the front portion of grill. Any boat interior shop has the material. Modify any large air leaks. Use the fan to keep fresh air filling vehicle, not recirculate.

Posted on Nov 16, 2008

  • 1 Answer

SOURCE: 1998 amigo timing 2.2 liter

The timing marks on the cam shaft sprockets are easily to see when you get the timing cover off. When the two cam shafts are lined up (pretty much at the top), then the crank should be almost down at the bottom.
Get yourself a good shop repair manual - I got mine from E-Bay for less than $15.00 (used).
Also, if your going to change the timing belt, have the water pump replaces at the same time.

Posted on Dec 28, 2008

motor1258
  • 6674 Answers

SOURCE: Cam Shaft Position Sensor 1998 Saturn SL

Have a look at this link, scroll to your engine & click on picture to expand for better view.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528017e904

Posted on Jan 23, 2009

  • 52 Answers

SOURCE: Adding freon to 98 Isuzu Amigo

You need to add the freon on the low side which is usually indicated by a blue cap. The red cap is the high side port. Never add freon using the high side port. Typically if you are buying a guage set from your local auto parts store, it will only attach to the low side service port because they are diffent types of connections. Another easy way to tell is to turn your AC on and feel the lines that the ports are attached to. The low side should be cold/cool and the high side will be hot.

Posted on Jun 28, 2009

  • 164 Answers

SOURCE: cam position sensor broke

ok easy fix. this is common on ALL ford w this style cam sensor,3.0 eats them for lunch. the sensor base has bushings like a real distributor, they get wore and fail. you can get new from ford, or reman at auto parts about 100 bucks. they come w the sensor installed but as with either, you need the allginment tool, looks like a little hockey puck, that only come from ford to set up or check engine light wont shut off. it will run without this but poorly. if you need more advice just post a comment to this and ill do my best to advise you

Posted on Sep 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 isuzu amigo 2.2L 5sp 2wd new NGK plugs & wires, fuel assembly, rail test, code -cam pos sensor?? still bucks, lurches, can't get 2 4,000 rpm 2 reset pcm, WTF?? 120,000 odo. Help us pls sir.


2.2L gas 2.2-liter petrol (X22SE)
or 2.2L
2.2L (X22se/D) Engine???
there are 3 engines

i cant guess engines yet, "Carnac the mag." is off line.
all i can tell from above is engine misfires.
when did it last run ok,, last week , last year, or found car in a barn.
history matters.
why not connect any $10 to $100 scan tool and scan it
running,,, it will infact ,tell you things, errors,called, DTC errors.
and is key to any diagnose of any modern engine in USA>.
even in canada the tool works starting in 1998.

is cam belt fresh? and timed correctly?
AMIGO, 2.2L (1 of 3)

first learn what under the hood.

please post what 2.2L is there. and fuel type.
gas, diesel ,petrol, ect

Mar 15, 2016 | 1998 Isuzu Amigo

1 Answer

Oxygen sensor on a 1998 isuzu amigo


what is the question? non stated,
where is it
where to buy it
what does it do
how to.
when do
how to...
questions

Jan 27, 2016 | 1998 Isuzu Amigo

1 Answer

Coolant temp sensor location on 1998 Isuzu Amigo 2.2L 4X4.


Go in on utube and ask the question Where is the 1998 Isuzu amigo coolant temp sensor located good luck

Oct 22, 2014 | 1998 Isuzu Amigo

1 Answer

99 amigo Timing???????


you should not change the belt maybe now its not in the same position and that's a big problem

Mar 13, 2012 | 1998 Isuzu Amigo

1 Answer

HI. I'M HAVING SOME REAL DIFFICULTY WITH MY 99 ISUZU AMIGO 2.2L 5SPD 4CYL... I JUST HAD A NEW HEAD GASKET PUT ON, NEW AIR INTAKE MANIFOLD, NEW TIMING, NEW PLUGS AND WIRES, AND FLUIDS. MY CHECK ENGINE LIGHT...


This P0341 code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor. This is accomplished through a reluctor wheel attached to the camshaft that passes by the cam sensor. Any time that the signal to the PCM is inconsistent with what the signal should be, this code is set. NOTE: this code can also be set by extended cranking periods.

The repair is to first verify that the ignition timing is set correctly. based on your description, it sounds like the family mechanic screwed it up. Go find someone competent and get the timing verified to be correct. Timing that is WAY out of adjustment can also cause this problem.

Aug 14, 2010 | 1998 Isuzu Amigo

1 Answer

Is there any way to clean oxygen sensors to make em last longer? 1998 isuzu amigo 2.2l 5spd check engine light is on 5 codes come up on obd 2 reader: p0134 po135 po342 p0134pd p0135pd what do they mean ? i...


if the wires are not damaged , washing them in vinegar to remove the exhaust build up on the sensor tip sometimes helps
code p 0134 refers to heated oxygen sensor (HO2S) 1 bank 1 --no activity detected ===causes--- wiring open circuit ---heating inoperative ---HO2S
it also refers to oxygen sensor (O2S)--no activity detected ====causes --wiring ---O2S
code p 0135 refers to HO2S 1 bank 1--heater control -circuit malfunction===causes ---fuse ,wiring ---HO2S---ECM
code p 0342 refers to camshaft position (CMP) sensor A , bank 1---low input ===causes ---wiring short to ground -- CMP sensor ---ECM

oxygen sensors have delicate wiring in the harness so they are easily damaged when the correct sensor tool is not used in the installation or removal process or the wires are pulled when disconnection the connection plugs

Jul 15, 2017 | 1998 Isuzu Amigo

2 Answers

1998 isuzu amigo 2.2l 5 spd 4 cyl .\r\ni need to


in all fuel injected cars you do not adjust idle. All you can do is clean the throttle and replace the Idle Air Control valve and check data thru a scanner to see if any sensors are out of specs. If this car has a maf sensor in the air filter tube it could become contaminated and cleaning or replacemnet will allow it to see more air which in turn allows the computer to add more fuel for better idling and accelration.

Jun 11, 2010 | 1998 Isuzu Amigo

2 Answers

How do I replace the camshaft position sensor on an amigo


4cyl? Its behind th timing cover between the cam pulleys. Should take about 15 minutes to replace. loosen upper cover and pull back to expose part

Aug 31, 2009 | 1998 Isuzu Amigo

3 Answers

1998 amigo timing 2.2 liter


The timing marks on the cam shaft sprockets are easily to see when you get the timing cover off. When the two cam shafts are lined up (pretty much at the top), then the crank should be almost down at the bottom.
Get yourself a good shop repair manual - I got mine from E-Bay for less than $15.00 (used).
Also, if your going to change the timing belt, have the water pump replaces at the same time.

Sep 12, 2008 | 1998 Isuzu Amigo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...