Question about 2007 Cadillac SRX

1 Answer

2007 Cadillac 3.6L srx, check engi, code p00017 crank sensor - replaced, still running rough and giving me a misfire on 1,3&5. Changed plugs, still 1,3&5 misfire - 155000 miles, could it need new coil

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cadillac Master
  • 11,756 Answers

P0017 timing chain Chevy Colorado P0017 Case Study Part 1
155,000 miles This is not a DTC for the crank sensor . This is for variable valve timing .
DTC P0017: Crankshaft Position (CKP) - Exhaust Camshaft Position (CMP) Correlation Bank 1
The camshaft position (CMP) actuator system enables the engine control module (ECM) to change the timing of the camshafts while the engine is operating. The CMP actuator solenoid signal from the ECM is pulse width modulated (PWM). The ECM controls the CMP actuator solenoid duty cycle by controlling the amount of solenoid ON time. The CMP actuator solenoid controls the advance or the retard of each camshaft. The CMP actuator solenoid controls the oil flow that applies the pressure to advance or retard the camshafts.
Ignition voltage is supplied directly to the CMP actuator solenoid. The ECM controls the solenoid by grounding the control circuit with a solid state device called a driver. The ECM compares the camshaft position or the camshaft angle, to the position of the crankshaft.

Your a little out of your league on this ! Your best bet ,take it to a qualified repair shop !

• Inspect the engine for any recent engine mechanical repairs. An incorrectly installed camshaft, camshaft actuator, camshaft sensor, crankshaft sensor, or timing chain can cause this DTC to set.
• An actuator that is in the full advance or retard position can cause this DTC to set.
• The presence of DTCs P0008 and P0009 along with P0016, P0017, P0018, and P0019 indicates a possible condition with the primary timing chain and the alignment between both intermediate sprockets and the crankshaft. Or, the crankshaft reluctor wheel has moved and is no longer referenced to top dead center (TDC).
• Observing the desired and actual camshaft angle parameters, with a scan tool before a DTC sets, may help to isolate whether a condition is specific to one camshaft, one bank, or caused by a condition with the primary crankshaft timing.

Posted on Jan 02, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2008 cadillac srx engine light came on and engine power reduce took it to the dealer so they changed the crank shaft sensor but its still not working, can you please help me


if they didn't read the fault codes before starting work, they are repairing by replacement and that is not good
if a sensor is faulty and it could be a cam shaft sensor as well as a crankshaft sensor , normally it misfires or stops altogether
the ECM is in limp mode and that reduced the engine power and if there was a sensor problem it would not just reduce power and put the light on but would show up in a define manner
engine lights also come on it there is a transmission problem and that will also initiate the limp mode
have the fault codes read to determine the faulty part/ sensor

Sep 10, 2016 | 2008 Cadillac Srx

1 Answer

Both coils do not fire on 1 and 4. Will start but only running on 2 cylinders. Could both coils be bad or should I look elsewhere?


Part 3 -How to Test the Ignition Module and Crank Sensor ...

easyautodiagnostics.com > Ford > 2.3L
Mar 1, 2012 - Spark plugs for cylinders #2 and #3 get spark at the exact same time. ...voltage -12 Volts) to both individual ignition coils within the coil pack. ... Ford Mustang or Ranger (or 2.3L Mazda B2300), this is what you'll need ... for this 'Switching Signal' at the coil pack... but you can also test this ... 1991, 1992, 1993.

How to Diagnose a Misfiring Cylinder (2.3L Ford Ranger ...

troubleshootmyvehicle.com > Ford > 2.3L
Apr 3, 2012 - Bad Fuel Injectors can cause a Misfire Condition. ... the ignition system on the 2.3L Ford Mustang or Ranger consists of 2 ignition coil packs, ...

2002 ranger misfire rough idle - Discussion on Topix

www.topix.com > Ford Ranger
Jul 27, 2007 - My truck is giving the code misfire in number 4 cyl. I replaced my spark plugs, Wires, Coil packs (both of them) and all my fuil ... three (3.0L v6) go bad, the fuel/air mixture gets messed up. Judged: 2. 2 ... My truck runs rough only at idle. ...code for ford ranger 2002, 2.3 5speed. truck runs like a champ but that ...

Extremely stumped! I need the best and brightest 1994 Ford ...

answers.edmunds.com > Edmunds Answers

Jan 31, 2016 | Cars & Trucks

2 Answers

Can I drive my car till my shop appointment on monday with codes PO204 and PO304


Re: P0204 and P0304 codes - Cadillac Forums

www.cadillacforums.com/.../cadillac-srx...2004/260084-p0204-p0304-c...
May 15, 2012 - 13 posts - ‎3 authors 2004 SRX is missiing on #4. I have replaced the injectors, I have Ohmed out the injector wiring without it attached to the injectors.(I jumpered ... Re: Help needed on '04 CTS 3.6L - Rough idle - P0302 ...
15 posts
Mar 11, 2014
Help with 2005 STS misfire P0304
9 posts
May 4, 2012
Re: p0204 p0304 codes - Cadillac Forums
5 posts
Jan 13, 2012
2005 Cadillac 3.6 Multiple Misfire Codes F.Y.I ...
8 posts
Sep 19, 2010
More results from www.cadillacforums.com

Nov 29, 2015 | 2004 Cadillac CTS

1 Answer

2006 srx strats then dies


check for cylinder compression's,take it from there

Jun 10, 2017 | 2006 Cadillac SRX

1 Answer

I have a 2007 jeep patriot. It stalled at stop sign started ran rough. Parked came back drove it home ran u- scan code p0017 replaced crank and cam sensors still runs rough changed plugs were bad. I was...


code p0017 refers to crank/ cam oosition sensor bank 1 sensor B -correlation ===causes --wiring--CKP sensor--CMP sensor--mechanical fault.
It also refers to control modules, cooling fan--no signal===causes -- wiring--ECM.
If it has a timing chain then the the advice that it will not be the chain is good. So I suggest checking out the cam/ crank sensors and wiring

Oct 22, 2013 | 2008 Jeep Patriot

2 Answers

2007 cadillac cts engine cylinder misfire


Error code p0300 indicates rough idle and p0305 indicates engine misfire in cylinder 5. Check for faulty spark plug and its wiring. Also check for ignition coil and distributor. Replacing spark plug and its wiring may resolve the issue.

Jun 28, 2013 | 2007 Cadillac CTS 3.6L

1 Answer

How replace spark plugs on a 2004 chevy blazer


Do you have a code scanner? What code does it give? If you don't have a scanner and the car is drivable take it to an autozone and have them hook it up to the scanner to get the code or you can buy a cheap scanner for $50 if the blazer was not running rough before you may have not pushed a plug wire on completely and now the engine is misfiring on that cylinder. how many miles on blazer? the platinum plugs from should be good for 100K miles.

Apr 01, 2012 | 2004 Chevrolet Blazer

3 Answers

2003 cadillac cts 3.2 liter..rough idle, scan tool shows misfire on bank 1, cylinders 1,3,&5. only at idle, scan tool also showed a cam postion sensor code. cam position sensor changed. no change in...


Did you ever find a solution to this? I am having the same issue on 2,4,6. I have replaced the coils. checked the intake for vacuum leaks. I am lost here let me know if you find anything and I will do the same.

Jan 08, 2011 | 2003 Cadillac CTS

9 Answers

Misfire #3 cylinder


Has anyone found the problem? My 2003 has #3 cyclinder misfire and I have replaced the plugs and wires. It runs rough at idle but smooths out at highway speed. Anyone have any knowledge on this? This sounds like a common problem.

Sep 09, 2009 | Cars & Trucks

Not finding what you are looking for?
2007 Cadillac SRX Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...