Question about Hyundai Getz

Open Question

Hyundai getz 1.1 starts off and goes through the gears fine ,but if you stop and try to put in first gear it will not go in .you have to press the clutch pedal again to make it go in .

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

shanat
  • 359 Answers

SOURCE: Clutch problem

check the fluid level first, if its empty this will happen, if so full it and bleed the clutch, if not it could be the slave cylinder and failing both, it could be the clutch itself, easiest way to check is to see on the gearbox if the clutch is engaging when you press the pedal down.
just ask if you need more help

Posted on Jun 17, 2008

  • 2 Answers

SOURCE: Car wont start - sometimes

try to check you starter motor&connection wiring from gearbox if auto

Posted on Dec 10, 2008

Benimur
  • 6966 Answers

SOURCE: to change gears, I need to fully press down on my

Hi and welcome to FixYa,

In a manual 2001 Hyundai Accent, the clutch cable could be adjusted. The adjustment point is on the cable 'pad' where it enters the firewall in the engine compartment.
86c2d7d.jpg
To adjust, the slack or free play must be decreased. This is done by turning the adjusting nut clockwise. Check back by pressing on the clutch pedal to your preference.
73309c3.jpg
Good luck and thank you for using FixYa.

Posted on Feb 18, 2009

pippall
  • 1486 Answers

SOURCE: my audi tt quattro 2004 model yesterday stopped changing gears

Release bearing problem.Change the clutch Assembly

Posted on Jun 13, 2009

germcelchar
  • 389 Answers

SOURCE: 2002 Hyundai Accent won't go into gear.

Probably the arm that holds the rtelease bearing in the bell housing has slipped out of place. Get someone to depress the clutch while you check the arm is not loose. If the cylinders are working then its most likely the arm is disconected. If you are lucky you may get it put back in place by looking through the inspection hole but most likely you will have to seperate the engine and gearbox. Sorry I havent better news for you.

Posted on Aug 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why are shifts noisy with burning smell?


You do not say whether it is auto or manual, but I assume manual, and by the sounds of it the clutch is slipping due to wear.

There is a test you can do. Start the engine, put it in 3rd gear, apply the foot brake, and let the clutch out. The engine should promptly stall, and if not, you need a replacement clutch.
.

Apr 05, 2016 | 2006 Hyundai Getz 1.4

1 Answer

Daughters 2002 Hyundai Getz is stuck in what i think is second gear.


Worn Clutch plate or thrust plate.

Check if hydraulic Clutch
if so check clutch fliud level . Could be a faulty clutch master cyclinder in hydraulic system.

Jan 15, 2015 | 2002 Hyundai Getz

1 Answer

Hyundai getz problems forum


sounds like a universal joint problem the clue is the increasing rattle/vibration upon accelerating.have your mechanic put the vehicle up on the lift and check the universal joints. I personally don't feel that Hyundai has gotten their standard of reliability to the level of lets say Honda,Toyota,or Nissan.Granted the newer ones have a lot of warranty (And they need it)My recommendation would be if it is doable is to trade it in on a newer Hyundai or switch to a more reliable brand of vehicle. I have consistently purchased Toyotas and they are very reliable to upwards of three-hundred thousand miles given routine maintenance. I hope this was helpful? good luck

May 08, 2014 | 2005 Hyundai Getz 1.6

1 Answer

How can i tell if my wheel bearings need to be replaced without pulling off parts for hyundai getz 2002


Sound comparison.
Jack up one front wheel, and securely block the other 3 wheels. Start the engine and put the car in gear, and let the motor run the wheel .
Do not race the engine.
Listen to the sound it makes.
Now shut off the engine and do the same to the other front wheel.
Is one really noisy ?
That's the problem wheel.
Unless you car was in a flood, wheel bearings usually last a lifetime on most cars.
Be blessed.

Feb 17, 2013 | 2002 Hyundai Getz

1 Answer

Car wont start - sometimes


try to check you starter motor&connection wiring from gearbox if auto

Dec 10, 2008 | Hyundai Accent Cars & Trucks

1 Answer

Hyundai getz


if the speedo still works then it will need a spedo unit if the speedo doesn't work it is either the cable or the gear in the trans to check the cable unthread from trans and attach a drill to the cable innereds spin the drill if the speedo does not move replace the speedo cable

Aug 28, 2008 | 2002 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...