Question about 2006 Audi A4

Open Question

What could be the cause of permanent flashing on the gear shift selector position window.This is on an Audi A 4 Automatic 2006 model

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

05 Trailblazer transmission says neutral but gear shiftier is locked in park.


Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock control solenoid
• The automatic transmission shift lock control switch
With the ignition in the ON position, voltage is supplied to automatic transmission shift lock control switch. Voltage flows through the normally closed contacts of the automatic transmission shift lock control switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid causing the transmission shift lever to be physically locked in the PARK position. When the brake pedal is pressed the contacts in the automatic transmission shift lock control switch open, de-energizing the automatic transmission shift lock control solenoid. This allows the shift lever to be move out of the PARK position.

Circuit Description
The transmission range (TR) switch is part of the park/neutral position (PNP) and back-up lamp switch assembly, which is externally mounted on the transmission manual shaft. The TR switch contains four internal switches that indicate the transmission gear range selector lever position. The powertrain control module (PCM) supplies ignition voltage to each switch circuit. As the gear range selector lever is moved, the state of each switch may change, causing the circuit to open or close. An open circuit or switch indicates a high voltage signal. A closed circuit or switch indicates a low voltage signal. The PCM detects the selected gear range by deciphering the combination of the voltage signals. The PCM compares the actual voltage combination of the switch signals to a TR switch combination chart stored in memory.

These are all electronically controlled , yur best bet would be to take your vehicle to the dealer .

Apr 19, 2017 | 2005 Chevrolet TrailBlazer

1 Answer

2003 Silverado 4WD. Service 4WD dash light comes on after engaging 4WD and acts up by engaging itself randomly for several days, then goes back to normal.


Check connection at the 4X4 control module , check power and grounds . Do you know how to do basic electrical testing ? Does your truck have manual or automatic trans mission ? Which transfer case does yours have ?

The NVG 263 transfer case features a three button shift control switch located on the instrument panel. When the ignition is in the RUN position, the transfer case shift control module (TCCM) starts monitoring the transfer case shift control switch to determine if the driver desires a new mode/gear position. At a single press of the transfer case shift control switch, the lamp of the new desired position begins flashing to inform the driver that the TCCM has received the request for a new mode/gear position. The lamp continues to flash until all shifting criteria has been met and the new mode/gear position has been engaged. Once the new mode/gear position is fully active, the switch indicator for the new position remains ON constantly. In the event that the TCCM can not or will not complete the shift, the indicator returns to the previously selected position; this is a Transfer Case Shift Control Switch Indicator Flashes, then Returns to Previous Mode condition.

The NVG 263 transfer case provides the driver with 4 manual mode/gear positions:
• 2HI - 2 Wheel Drive high range
• 4HI - 4 Wheel Drive high range
• 4LO - 4 Wheel Drive low range
• Neutral
Have it check for DTC'S - diagnostic trouble codes ?

DTC B0790
DTC B2725
DTC C0306
DTC C0327
DTC C0359
DTC C0379
DTC C0550

Your best bet would be take it to a qualified repair SHOP

Dec 28, 2016 | Cars & Trucks

1 Answer

My reverse lights and my brake lights will not work with the anti theft light on in the dash


These lights are all computer controlled ! Several modules involved DIM - dash integrated module , RIM - rear integrated module .They share information on serial data communication network . Class 2 an or GMLAN !
The rear fuse block supplies battery positive voltage through the REVERSE LAMP fuse to the coil and switch terminals of the reverse lamp relay. The DIM sends a power mode message to the RIM indicating that the ignition is in the ON position. When the driver of an automatic transmission equipped vehicle places the gear selector in the REVERSE position, the powertrain control module (PCM) sends a class 2 message to the RIM. The message indicates that the gear selector lever is in the REVERSE position. When the driver places a manual transmission equipped vehicle in reverse the reverse gear position switch mounted on the transmission closes. This provides a ground for the reverse gear position switch signal line, informing the RIM that the transmission is in reverse. For both automatic and manual transmission vehicles the RIM then grounds the control circuit of the reverse lamp relay . This energizes the reverse lamp relay, closing the switch side contacts and providing battery positive voltage to the backup lamp bulbs. The backup lamps are permanently grounded at G402. With both power and ground the backup lamp bulbs illuminate. Once the driver moves the shift lever out of the reverse position a message is send either by class 2 by the PCM or the reverse gear position switch opens causing the RIM to remove the ground from the reverse lamp relay control circuit. This opens the contacts in the relay turning OFF the backup lamps.
This is something best left to the dealer or a ASE certified repair shop . Need a factory or professional grade scan tool to diagnose an repair this . http://www.public.asu.edu/~pheanis/documents/VBI_CAN.pdf

Feb 20, 2016 | 2006 Cadillac CTS 3.6

1 Answer

2006 Rosa bus, model PA-BE64DJ automatic transmission. Where can I get gear selector switch?


PDF]TRANSMISSION Workshop Manual FR M/T (W-E)

www.mitsubishi-motors.kiev.ua/Manuals/Transmission/.../22D.pdf
Transmission Model. Gear ratio. Speedometer gear ratio. Vehicle Model. EngineModel. EUR ... 0.856. Reverse. 4.142. 3.578. V5M21 TRANSMISSION MODEL. Gearratio. A. B. C. 1st. 4.330. 3.967 ... Transmission. Backup lamp switch. 29 ± 2.

[PDF]BONLUCK BUS & COACH - Australasian Bus and Coach

www.busnews.com.au/media/.../abc_310_p72-73_classifieds-1-.pdf
LUGGAGE BINS RADIO,CD,P.A.. DISC BRAKES ... THE BUS YOU WANT IS NOW EASIER TO FIND ... 2006 MITSUBISHI ROSA DELUXE AUTO ... 25 Seater, 4 Cyl Turbo Diesel Automatic Transmission, Highback ... 2009 MODEL $120,000 + $12,000 GST = $132,000 ..... 50 seater, engine-gear box rebuild - only 130 000km.Missing: be64dj ‎selector ‎switch

Dec 18, 2015 | Mitsubishi Cars & Trucks

2 Answers

This morning it started fine but will not come out of gear and my airbag light is on. Someone said it was the fuse but I am not sure which fuse. Any ideas ?


I am mechanic I really need to no more make ect. but it could be battery or the ignition switch or ignition lock n key but like I said need more information this is a guess that I told you

Oct 21, 2015 | 2008 Chevrolet Chevrolet TrailBlazer LT

1 Answer

How do I get unstuck from park?


Vehicles have a safety system that won't allow gear selector to be moved out of park unless brake pedal is pushed ! This what Buick calls there's
Automatic Transmission Shift Lock Control ! Depending on make of your vehicle it mite be called something else . But all vehicles have it.
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the ignition is ON. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid


?€¢
The automatic transmission shift lock control switch


?€¢
The brake to shift relay


?€¢
The rear integration module (RIM)

With the ignition in the ON position, battery positive voltage is supplied to the brake to shift relay coil. When the RIM energizes the brake to shift relay, the brake to shift relay switch contacts close suppling battery voltage to the automatic transmission shift lock control switch. The circuit continues through the normally closed switch to the automatic transmission shift lock control solenoid. The permanently grounded solenoid is energized. This locks the shift linkage in the PARK position. When the driver presses the brake pedal, the contacts in the automatic transmission shift lock control switch open. This causes the automatic transmission shift lock control solenoid to release. This allows the shift lever to move from the PARK position.

Sep 08, 2015 | Cars & Trucks

1 Answer

Shifter is locked in park on a 2002 bravada that sayes on dash its in reverse


PRND321 Display
The instrument panel cluster (IPC) displays the selected gear position as determined by the engine control module (ECM). The IPC - instrument panel cluster receives a serial data message from the ECM indicating the gear position. The PRND321 display blanks if:
?€¢
The ECM detects a malfunction in the transmission range switch circuit.


?€¢
The IPC detects a loss of serial data communications with the ECM. The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid


?€¢
The automatic transmission shift lock control switch

With the ignition in the ON position, voltage is supplied to automatic transmission shift lock control switch. Voltage flows through the normally closed contacts of the automatic transmission shift lock control switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid causing the transmission shift lever to be physically locked in the PARK position. When the brake pedal is pressed the contacts in the automatic transmission shift lock control switch open, de-energizing the automatic transmission shift lock control solenoid. This allows the shift lever to be move out of the PARK position.
The transmission range (TR) switch is part of the park/neutral position (PNP) and backup lamp switch assembly, which is externally mounted on the transmission manual shaft. The TR switch contains four internal switches that indicate the transmission gear range selector lever position. The PCM supplies ignition voltage to each switch circuit. As the gear range selector lever is moved, the state of each switch may change, causing the circuit to open or close. An open circuit or switch indicates a high voltage signal. A closed circuit or switch indicates a low voltage signal. The PCM detects the selected gear range by deciphering the combination of the voltage signals. The PCM compares the actual voltage combination of the switch signals to a TR switch combination chart stored in memory.
You need a Tech2 scan tool to diagnose this problem ! possible range sensor !

Sep 03, 2015 | Cars & Trucks

1 Answer

The gear shifter on my 1998 Pontiac SE coupe will not unlock so I can take the car out of park


Do you have column or floor shifter ?
All automatic transaxle models use an electric park lock system. Within the housing assembly, a lock cylinder is connected to an actuator which rotates and engages on the electric park lock solenoid. When the floor-shift lever is not in the park position, the actuator disengages from the electric park lock solenoid slider. This allows the lock cylinder to move to the lock position. With the shift lever in PARK and the lock cylinder in LOCK, the actuator cam is positioned against the electric park lock solenoid slider. This prevents the shift lever from shifting out of the PARK position.
The column-shift automatic transaxle model uses a flexible cable actuator instead of an electric park lock system. One end of the cable is attached to the gate assembly. The other end of the cable is attached to the column mounted housing assembly. This system functions similarly to the floor-shift ignition lock system.
The manual transaxle model uses a push button lock cylinder. A clutch start switch is used. The clutch pedal must be pressed before the engine will crank. Refer to Park Lock System Check .
CAN you turn the key on ?
The gear selector does not shift out of PARK with the brake pedal depressed and the ignition switch in RUN.
Automatic Transmission Shift Lock Control Always On with Ignition in Run
Action
Value(s)
Yes
No

1

Was the BTSI System Check performed?
--
Go to Step 2
Go to Automatic Transmission Shift Lock Control System Check

2

Is this a column shift vehicle?
--
Go to Step 3 yes
Go to Step 4 no

3

  1. Move the gear selector to the PARK position.
  2. Disconnect the automatic transaxle control connector
  3. Turn the ignition switch to RUN.
  4. Connect the test lamp between terminal B and ground.
Does the test lamp light?
--
Go to Step 4
Go to Step 8

4

  1. Disconnect the brake switch connector C2.
  2. Move the ignition switch to RUN.
Can you shift the transaxle out of the PARK position?
--
Go to Step 5
Go to Step 8

5

Is the brake switch adjusted properly?
--
Go to Step 6
Go to Step 7

6

Replace the brake switch.
Is the repair complete?
--
System OK
--

7

Adjust the brake switch.
Is the repair complete?
--
System OK
--

8

  1. Disconnect the BTSI solenoid connector (column shift vehicles) or disconnect the automatic transaxle control connector (console shift vehicles).
  2. Move the ignition switch to RUN.
Can you shift the transaxle out of the PARK position?
--
Go to Step 9
Go to Step 10

9

Repair the short to power in CKT 1135.
Is the repair complete?
--
System OK
--

10

Test for sticking or binding in the shift linkage.
Does the shift linkage stick or bind?
--
Go to Step 11
Go to Step 12

11

Repair the shift linkage.
Is the repair complete?
--
System OK
--

12

Replace the BTSI solenoid (column shift vehicles) or replace the automatic transaxle control (console shift vehicles).
Is the repair complete?
--
System OK
Go to Step 1

May 18, 2015 | Pontiac Cars & Trucks

1 Answer

Desciption of the gear positions on the automatic gear shift


The gearbox normally shifts like this in "D":

1st gear to 2nd gear

2nd gear to 3rd gear

3rd gear to OverDrive

If you have the selector in "2", it will not make the final 2 shifts. "2" is nice for descending very steepo hills slowly, and also is nice to use coming down hills when it is icy/snowy, the engine will slow down in "2", and you will not have to depress the brake pedal.

Apr 09, 2009 | 1996 Toyota RAV4

Not finding what you are looking for?
2006 Audi A4 Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14200 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...