Question about 2006 Audi A4

Open Question

What could be the cause of the permanent flashing of the gear selector window of Audi A 4 2006

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75117 Answers

SOURCE: audi 80 wont go into any gear

I think it is the transmission that has failed.

Posted on Jul 13, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which sensor is responsible for gear shifting in 1996 audi a4,1.8t


Their is a 'gear selector' on the driver side of the tranny. Shown in the bottom of the pic
sensor-responsible-gear-shifting-in-1996-vrlqwrordquuw1cb1trscexg-4-1.jpg

Jan 22, 2015 | 1996 Audi A4

1 Answer

Audi 2002 a4 v6 2.4l when the car first starts the RPMs surge up and down unsteadily this stops if you give a few revs on the accelerator pedal. When driving around 50kph the rpms surge slightly it feels...


You have two problems. The surging is from a dirty throttle body and /or air filter. The selector light could be from a bad selector switch or internal transmission problems. Have the car scanned for codes.

Oct 20, 2014 | 2002 Audi A4

1 Answer

Audi 2002 a4 v6 2.4l when the car first starts the RPMs surge up and down this stops if you give it some accelerator pedal. when driving around 50kph the rpms surge slightly it feels like a gentle tug...


It seems like you need to have your car's TCM scanned .The flashing lights always mean a TCM going bad.You can get a rebuilt one for around $300-$400 www.programainc.com/ in Boca Raton Fl.If you live in South Florida Call German Car Depot 954-921-1515 we can scan and install a new one if needed. Ollieracepnc

Oct 20, 2014 | 2002 Audi A4

1 Answer

Audi 80 wont go into any gear


I think it is the transmission that has failed.

Jul 13, 2012 | 1991 Audi 80

1 Answer

Gear shifter is stuck on park on my 2007 caliber


PERMANENT FIX that doesn't cost a dime or require any tools. It happened to me by accident. Break the detante by moving the gear selector while holding the manual override lever (plastic lever inside the access hole). Once it is gone no matter what the brake switch calls for (lock gear selector or not) the gear selector will always be movable because the mechanical locking mechanism is no longer there. TADA!!! So what if you no longer have to depress the brake pedal in order to change gears. Call it a retro fix.....!

Oct 23, 2010 | 2007 Dodge Caliber SXT Sport Hatchback

3 Answers

Prob's with my Audi A6 2003 Auto 3.0 V6 (gearbox)


Doubt it as the fault suggests you need to look into the range sensor. If similar to Renault there is a switch on the gearbox that senses where the select lever is (at the gearbox end). If the display is wrong then the sensor needs looking at and either it will need to be adjusted into a set position by moving it, or perhaps the connector to it or wiring to/from it have a fault.

May 08, 2010 | 2003 Audi A6

1 Answer

Gearshift selector problem


The gear selector switch is either out of adjustment or it is bad. Loosen the two bolts holding the gear selector in place and turn it slightly to see if the display stops flashing. You will have to manually shift the transmission lever at the switch into neutral, and then turn the switch until the display says neutral. Tighten the bolts and then check all gears. It's also possible the shift cable could also be out of adjustment. Does the display change if you simply wiggle the gear selector lever?

Oct 22, 2009 | 1988 Oldsmobile Toronado

1 Answer

Sometimes can't get reverse gear Audi A6 2004 Auto 1.9TDi UK


Unless your shade tree mechanic is an Audi expert, go to the dealer who has all the books and diagrams that tell the tech exactly where to look. The other guy may want to replace something just to troubleshoot and the factory tech should know exactly what to replace or which plug is loose.

Sep 20, 2009 | 2003 Audi A6

1 Answer

I have installed a new clutch on my AUDI 1.9tdi N reg 1996. as old clutch burnt out. However when the car broke down i could only select 3rd gear. i have bled clutch correctly & its still only letting...


With the engine off, you should be able to select all gears (with the clutch depressed). If you can the clutch is not adjusted correctly, if you can't the gear selector fork may be worn or just have no oil in the box.
It will not cause the clutch to burn out, probably the clutch will cause the gears to grind instead.

Jul 02, 2017 | Audi A4 Cars & Trucks

Not finding what you are looking for?
2006 Audi A4 Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14223 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...