Question about 2006 Audi A6

Open Question

2006 audi A6 remote start

Happy New Year! I installed dball2 + RS - 2006 Audi A6. After installation, the engine is not switched off when the ignition key is turned off. Then I, the gray wire + ignition status output 6p-12, with a diode connected to ON1 RS unit and the pink wire + ignition input 9p-10 connected to the ON2 RS unit. Everything was fine. What's the matter? My RS unit did not had a minimum of 10 seconds, wait to start at least was 15sec.. And so, the engine starts at the second attempt.After,I'll put 7-8 sec. timer relay.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: audi a4 problem

I had this problem with my old Audi 80 and basically it was a knackered fuel pump. If your car is a few years old avoid the main Audi dealers and take it to an independant Audi/Volkswagon specialist and you will save a small fortune.

Posted on Jul 28, 2008

tommyboinow
  • 324 Answers

SOURCE: problems with my 1995 Audi A6 QUATTRO

replace the coil pack, sounds like it is over heating.

Posted on Nov 26, 2008

mcgyver468
  • 710 Answers

SOURCE: Audi A6 2004, 2.0TDi won't start when ignition switched on.

Could be neutral safety switch connector. May have a loose plug on the switch. Hope this helps. Best of luck to you.

Posted on Apr 28, 2009

  • 2 Answers

SOURCE: Car doesn't Start after suden loss of power

Either charge or replace your battery or check for any faulty wires that could have been damaged by the excess loss of power if it was due to a short circuit.

Posted on May 17, 2009

co7196
  • 3433 Answers

SOURCE: Audi A6 Starting problem

Try starting without touching gas pedal

Posted on Oct 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A6 turbocharged. Whyu does it smoke when it covers a 120km per hour?


I am going to say 'blown turbo'. As I understand it, they needs replacing every few years. They are susceptible to heat and incredible revolutions. They have to be lubricated, the seals go, and you get smoke.

Mar 20, 2016 | Audi Cars & Trucks

1 Answer

How to replace audi a6 3.2 climate control


Yes it needs to be coded and adapted for that car so it works with equipment installed . Depending on year it may need to be released from component protection mode, thats an anti theft mode.

Mar 01, 2015 | 2006 Audi A6 3.2

1 Answer

Where exactly is the cabin filter in 2006 Audi A6 sedan, and how to replace it?


The cabin air filter is placed on the right bottom side of the dash panel - passenger side, for 2006 Audi A6. Remove the carpet and behind the plastic cover is the cabin filter. When installing new filter see for the correct position - air flow is indicated by arrow. See pictures below:

tdisline_252.jpg
Please do rate my response. Thanks!

Feb 12, 2011 | 2006 Audi A6

1 Answer

Installing cabin filter on 2006 audi a6


See pictures below:

tdisline_232.jpg
Please do rate my response. Thanks!

Feb 07, 2011 | 2006 Audi A6

1 Answer

2006 Audi A6 Avant Drivers window control panel


Replace the switch. It has lost connection to the up position.

Sep 11, 2010 | 2006 Audi A6

1 Answer

My TT was imported new from Japan....Has AMAZING video and sound system unfortunateley its all Japanese to me!! The manual that comes with it is about an inch think...Its got built in Navigation system...


I know you can that you can change this by simply hooking up a scan tool for specific year. There are language options accessible for situations like this. Here is a sample of what can be changed using VAG 5052 or equivalent scanners.

Coding
  • 0?xxxxx: Model
    • 1 = Lamborghini
    • 2 = Audi A3 (8P)
    • 3 = Audi A4 (8E)
    • 4 = Audi A4 Cabriolet (8H)
    • 5 = Audi A6 (4B)
    • 6 = Audi TT (8J)
    • 7 = Audi R8 (42)
  • 0x?xxxx: Treble Speaker Monitoring inactive
    • 0 = Front Treble Speaker Monitoring inactive active (NOT Audi A4 Cabriolet)
    • 1 = Front Treble Speaker Monitoring inactive inactive (ONLY Audi A4 Cabriolet)
  • 0xx?xxx: Sound Characteristic
    • 0 = Sound Characteristic linear
    • 1 = Audi A4 (8E)
    • 2 = Audi A6 (4B)
    • 3 = Audi A4 Cabriolet (8H)
    • 4 = Audi TT (8J)
    • 5 = Audi A3 (8P)
    • 9 = Sound System
  • 0xxx?xx: Telephone/Telematic
    • 1 = Telephone not installed (Remote Feed Voltage for Microphone active)
    • 2 = Base Plate (Temic - Remote Feed Voltage for Microphone inactive)
    • 3 = Base Plate (Cullmann - Remote Feed Voltage for Microphone inactive)
    • 4 = Base Plate (Nokia - Remote Feed Voltage for Microphone inactive)
    • 5 = Telematic Europa (Remote Feed Voltage for Microphone inactive)
    • 6 = Telematic US (Remote Feed Voltage for Microphone inactive)
    • 7 = Base Plate diagnostic capable with Comfort Control
  • 0xxxx?x: Equipment I
    • 1 = Tuner not installed
    • 2 = Digital-Radio installed
    • 3 = Satellite-Radio installed
    • 4 = Satellite and Digital-Radio installed
    • 5 = Analog Input (AUX) installed
    • 7 = Satellite-Radio & Analog Input (AUX) installed
  • 0xxxxx?: Equipment II
    • 1 = TV-Tuner/CD-Changer/Multi-Function Steering Wheel not installed
    • 2 = TV-Tuner installed
    • 3 = CD-Changer installed
    • 4 = TV-Tuner and CD-Changer installed
    • 5 = Multi-Function Steering Wheel installed
    • 6 = TV-Tuner and Multi-Function Steering Wheel installed
    • 7 = CD-Changer and Multi-Function Steering Wheel installed
    • 8 = TV-Tuner and CD-Changer and Multi-Function Steering Wheel installed



Adaptation Channel 001: Tire Circumference The tire circumference is beeing adapted in "mm".


Channel 002: Wheel Pulse The wheel pulse describes the amount of wheel pulses per revolution.
If value 0 is entered the system calibrates automatically itself after several kilometers and inputs a value.

  • 43 = Audi A3 (8P) / Audi TT (8J)
  • 45 = Audi A4 (8E)


Channel 003: Language (Screen)
  • 0 = German
  • 1 = English (UK)
  • 2 = French
  • 3 = Italian
  • 5 = Spanish
  • 6 = Portuguese
  • 7 = English (UK)


Channel 004: Back-Up Camera
  • 0 = Back-Up Camera not installed
  • 2 = Back-Up Camera installed


Channel 005: Speed Threshold (Video Input)
  • 0 = max. 0 kph or 0 mph
  • 1 = max 5 kph (Standard for Europe)


Channel 007: Options Channel 008: Volume Characteristic Channel 010: Region
  • 0 = Europe/North America
  • 1 = Australia/South America
  • 2 = South Africa


Channel 011: Language (Speech Recognition)
  • 0 = German
  • 1 = English
  • 2 = French
  • 3 = Italian
  • 5 = Spanish


Channel 018: Start Screen The start screen setting has to correspond with the control module coding, e.g. a S3 start screen doesn't work with an A4 coding.

  • 0 = Standard Start Screen
  • 1 = Audi S3 Start Screen
  • 2 = Audi S4 Start Screen
  • 3 = Audi RS4 Start Screen
  • 4 = Audi TT Start Screen
  • 5 = Audi R8 Start Screen


Channel 065: Read Test Channel 066: Self Test Channel 067: CD/DVD Drive
  • 000 - Normal/Eject-Button enabled
  • 001 = Eject CD/DVD (will not be saved)
  • 255 = Eject-Button disabled/locked (Anti-Theft-Protection)


Channel 068: Screen Test Values will not be saved, they only act as initiation for each Test Picture.

  • 0 = No Test Picture
  • 1 = Test Picture: Red
  • 2 = Test Picture: Green
  • 3 = Test Picture: Blue
  • 4 = Test Picture: White
  • 5 = Test Picture: Black
  • 6 = Test Picture: Checkerboard
  • 7 = Test Picture: Checkerboard (inverted)
  • 8 = Test Picture: 64 Gray Scales (vertical Bars)
  • 9 = Test Picture: Special


Channel 069: Display Mechanism
  • 000 = Display closed
  • 001 = Display open
  • 200 = Display half open (Obstacle)
  • 255 = Position undefined


Channel 070: Display Brightness
  • 0 = 0% Brightness (Display OFF)
  • 1 = 20% Brightness
  • 2 = 40% Brightness
  • 3 = 60% Brightness
  • 4 = 80% Brightness
  • 5 = 100% Brightness


Channel 099: Transport Mode Only applies to models without Gateway/Diagnostic Interface for Databus.

  • 0 = Transport Mode inactive
  • 1 = Transport Mode active


Channel 111: Reset
  • To perform a system reset/restart save 1 as new value.


Channel 114: FM Frequency
  • Range: 875...1080


Channel 117: Signal Test (Output)
  • 0 = Fader Center & Balance Center
  • 1 = Fader Front & Balance Left
  • 2 = Fader Front & Balance Right
  • 3 = Fader Rear & Balance Left
  • 4 = Fader Rear & Balance Right


Channel 136: Driver Position
  • RNS-E Basic
    • 03226 = Left-Hand-Drive (LHD)
    • 02632 = Right-Hand-Drive (RHD)
  • RNS-E High/US
    • 00005 = Left-Hand-Drive (LHD)
    • 00013 = Right-Hand-Drive (RHD)

Jul 04, 2010 | 2007 Audi TT

1 Answer

How to change rear brake pads on audi a6 2006


Remove the tires, Remove the calaper bolts, (small heads on them 12mm or so) Remove calaper, Pads are setting in a holder. Lube new pads with litheum grease and place in holder. (look at old pads, one or both may have small metel tab on one end) If the new pads have the tab, put that pad where the old pad with the tab was. (ie. tab to the inside) Press pistion in with a 'C' clamp. If it won't go in easly, it may screw in. If the parking brake cable is hooked to the calaper, it probly screws in. Use large pliers to screw in calaper piston. Place calaper over pads and install bolts (lube bolts) Rember to pump brakes befor driving . to get a solid peddle.

May 20, 2009 | 2006 Audi A6

1 Answer

My serpentine belt came off my 2002 A6 Audi 3.0


This is tough to get to, the tensioner assembly is removed with a 10mm hex/alen wrench. You will not be able to see the bolt, it is recessed. When you install the new tensioner, there is an allignment pin that you must be careful to get in the hole in the engine block. The new tensioner will have a lock pin installed, leave it in until you get the belt on, then remove the pin.

Nov 27, 2008 | 2002 Audi A6

Not finding what you are looking for?
2006 Audi A6 Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14337 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...