Question about Ford F-250

Open Question

Can anybody tell me the color of the wires of the EBP sensor on a 2008 Ford F250 6.4 and in what order they go on the harness clip connect3

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: 1999 Grand Cherokee Radio Wiring Harness Diagram/Color Codes

Go to www.installdr.com and search through the diagrams in there, the site is easy to use, all you need is acrobat reader installed on your computer to use the site, it has a full explanation on every wire color and what it is

Posted on Aug 30, 2008

Ad
fastboyz
  • 674 Answers

SOURCE: 2008 E-350 IAT sensor wires

is this what you recieved?9af2263.jpg

Posted on Nov 12, 2008

CLEONTI
  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

  • 2 Answers

SOURCE: wiring diagram or color chart for a 96 ford mustang radio harness

dont even worrie about it just go to walmart or an auto parts and get a wiring harness they are not so expensive

Posted on Sep 06, 2009

ZJLimited
  • 17970 Answers

SOURCE: 2004 ford escape wiring diagram

This is for 2005 Escape, its possible that can helpfull... LINK

Hope this help.

Posted on May 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove bank 1 sensor 1 o2 sensor on a 2008 grand cherokee


Pop the plug off the clip. pull it down. Gives you a little more room to reach up and release it. and yes,, They are not fun to remove. But not impossible.

Oct 08, 2016 | 2008 Jeep Grand Cherokee Laredo

1 Answer

What are the fuel injector wire colors for a ford escape 2008 3.0L v6 4wheel drive?


Okay, you know each injector has a power wire, and a ground wire that goes into the pcm? All of the power wires to all six injectors is a green wire with a red stripe.

The ground wire colors are as follows:
inj 1: green wire/blue stripe.
Inj 2: gray wire/yellow stripe
Inj 3: violet wire/gray stripe
Inj 4: yellow wire/orange stripe
Inj 5: brown wire
Inj 6: green wire/white stripe

I should note that the wiring diagram I am looking at shows this diagram as from a 2008 model manufactured during 2nd quarter of the year 2008. If your injector wire colors are different than as listed above, there may have been production changes during the year. But the power wires to all six injectors would still have the same color wire. You could figure it out that way: in other words, looking at the injector harness, same wire color to all six is the power wire, all the odd colors are the ground wire for that injector. Hope this makes sense to you. Good luck.

Feb 03, 2015 | Ford Cars & Trucks

1 Answer

Audio wiring color codes 1994 ford explorer xlt


I installed a aftermarket radio and my battery Gage and my reverse lights and turn signals wont work now can anybody help

Sep 27, 2012 | 1992 Ford Explorer

1 Answer

To hook upa cd player after they have cut the factory plugs! there r 2 different ones. one clip has eight speaker wires abd the other clip has six wires! what wires do i hook togater to make it work?


your stereo should have come with a wiring diagram for it that at least tells you what color wire is what coming out of the stereo just match up the colors/signals per this chart: This for for a typical ford- http://www.installdr.com/Harnesses/Ford-Wiring.pdf

Feb 28, 2011 | 1995 Ford Contour

1 Answer

I need to know what P1247 means


this is hard to tell you when i have no year car or make or engine or model but il take a shot at it, p1247, this must be a newer ford with a 7.3 diesel engine, now am i doing? great the 1247 is low boost preasure, make sure there are no leaks on the pipes and gaskets to turbo or the exhaust, then remove the ebp sensor and clean also remove the pipe and clean out then reset your codes and drive. the ebp,exhaust boost preasure sensor. hope this helps also check the linkage to the waste on the turbo that sometimes falls off.

Aug 29, 2010 | Ford F-250 Cars & Trucks

1 Answer

My speed don't work


Speed Sensors REMOVAL & INSTALLATION Front Fig. 1: The speed sensor sits directly over the exciter ring in the front knuckle 89609p51.jpg
Fig. 2: Detach the speed sensor connector in the engine compartment 89609p55.jpg
Fig. 3: Remove the speed sensor harness from the routing clips 89609p53.jpg
Fig. 4: A special E6 Torx® socket is required to remove the speed sensor retaining bolt 89609p52.jpg
  1. Disconnect the negative battery cable.
  2. From inside engine compartment, detach sensor assembly 2-pin connector from the wiring harness.
  3. Remove the steel routing clip attaching the sensor wire to the tube bundle on the left sensor or remove the plastic routing clip attaching the sensor wire to the frame on the right sensor.
  4. Remove the rubber coated spring steel clip holding the sensor wire to the frame.
  5. Remove the sensor wire from the steel routing clip on the frame and from the dust shield.
  6. Remove the sensor attaching bolt from the front spindle and slide the sensor out of the mounting hole. To install:
  7. Install the sensor into the mounting hole in the front spindle and attach with the mounting bolt. Tighten to 40–60 inch lbs. (4.5–6.8 Nm).
  8. Insert the sensor routing grommets into the dust shield and steel bracket on the frame. Route the wire into the engine compartment.
  9. Install the rubber coated steel clip that holds the sensor wire to the frame into the hole in the frame.
  10. Install the steel clip that holds sensor wire to tube bundle on left side or plastic clip that holds sensor to frame on right side.
  11. Reconnect the 2-pin connector to wire harness. Connect the negative battery cable.
Rear Fig. 5: Detach the speed sensor connector in the luggage compartment 89609p04.jpg
Fig. 6: Grasp the harness and . . . 89609p37.jpg
Fig. 7: . . . remove it from the routing brackets 89609p36.jpg
Fig. 8: The rear speed sensor is mounted on the back of the hub assembly 89609p32.jpg
Fig. 9: Remove the sensor retaining bolt and remove the sensor from the hub 89609p34.jpg
  1. Disconnect the negative battery cable.
  2. From inside luggage compartment, detach 2-pin sensor connector from wiring harness and push sensor wire through hole in floor.
  3. From below vehicle, remove sensor wire from routing bracket located on top of rear axle carrier housing and remove steel clip holding sensor wire and brake tube against axle housing.
  4. Remove screw from clip holding sensor wire and brake tube to bracket on axle.
  5. Remove sensor to rear adapter retaining bolt and remove sensor. To install:
  6. Insert sensor adapter and install retaining bolt. Tighten to 40–60 inch lbs. (4.5–6.8 Nm).
  7. Attach the clip holding the sensor and brake tube to the bracket on the axle housing and secure with the retaining screw. Tighten the screw to 40–60 inch lbs. (4.5–6.8 Nm).
  8. Install steel clip around axle tube that holds sensor wire and brake tube against axle tube and push spool-shaped grommet into clip located on top of axle carrier housing.
  9. Push sensor wire connector up through hole in floor and seat large round grommet into hole.
  10. Reconnect sensor 2-pin connector to wiring harness inside luggage compartment.

Aug 03, 2010 | 1992 Ford Crown Victoria

1 Answer

I need to know what colors the wires are for the speakers and power so i can put a cd player in my 1986 ford f150


if u have the harness clip to plug into the factory wiring..ur speakers will be 2 green,2 purple,2 whit,and 2 grey..get the harness from walmart..8 bnucks..after that its cake work.

Mar 10, 2010 | 1986 Ford F150 SuperCab

2 Answers

Wiring diagram or color chart for a 96 ford mustang radio harness


dont even worrie about it just go to walmart or an auto parts and get a wiring harness they are not so expensive

May 28, 2009 | 1996 Ford Mustang

1 Answer

Need To Wire In A Aftermarket Radio In A 2008 F-150


Easiest way is to go to Crutchfield.com web site, When you order a radio face plate or factory wireharness they give you a free installation kit which shows the color codes of each wire for the radio. Also, when you get the wireharness you don't have to cut any factory wires, it just plugs into your factory harness and you connect the open ends to your new radio.

Dec 18, 2008 | 2008 Ford F 150 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5572 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...