Question about Renault Cars & Trucks

Open Question

I need a belt diagram for my Renault Ares 836 RZ tractor, running over 8 pulleys: crankshaft, waterpump, alternator, fan, a/c compressor, one ribbed idler, one smooth idler and smooth idler/tensioner.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 599 Answers

SOURCE: GET TENSION OFF THE IDLER PULLEY

loosen nut in center of idler pulley ..then loosen tension bar with 12mm socket til it walks away to remove belt

Posted on Jan 14, 2009

MrScary66613
  • 1990 Answers

SOURCE: Diagram for alternator/pulley belt.

If the Tensioner will not Tighten the Belt, It will be one of two Things. Either the Belt is too Long or the Tensioner is Bad and needs to be Replaced. Please Rate My Response! Thanks!

Posted on Feb 03, 2009

ewashmidas
  • 362 Answers

SOURCE: Serpentine belt routing

Here you go.. I looked up the same belt you did, it should be right.

adecd3f.png

Posted on Feb 09, 2009

mrgreenz
  • 962 Answers

SOURCE: serpentine belt slips off idler pulley

The A/C pully is supposed to spin freely until the AC is activated to run.. The cranshaft pully does not. Replace the tensioner pully. The belt has to fit in between the grooves on the pullys.

Posted on Apr 05, 2009

blueextc3221
  • 15935 Answers

SOURCE: Can't get A/C belt around pulleys on my 01 Chevy Tracker 2.5 V6


Removal & Installation

1.6L Engine
A/C Compressor Belt

  1. Disconnect the negative battery cable.
  2. Loosen the A/C compressor mounting bolts.
  3. Pivot the A/C compressor towards the engine in order to relieve the tension on the belt.
  4. Remove the A/C compressor drive belt from the pulleys.

To install:
  1. Properly route and install the A/C compressor drive belt on the A/C compressor, the power steering (if equipped), and the crankshaft pulleys.
  2. Adjust the A/C compressor drive belt to obtain 6-9 mm (0.24-0.35 in) deflection.
  3. Tighten the A/C compressor mounting bolts to 13-20 f t. lbs. (18-28 Nm).
  4. Connect the negative battery cable.

Alternator Belt
  1. Disconnect the negative battery cable.
  2. Remove the power steering pump and the A/C compressor drive belt.
  3. Loosen the generator mounting bolts.
  4. Pivot the generator towards the engine and remove the accessory drive belt.

To install:
  1. Properly route and install the generator drive belt on the pulleys.
  2. Adjust the alternator drive belt to obtain 6-8 mm (0.24-0.32 in) deflection for a used belt or 5-6 mm (0.20-0.24 in) deflection for a new belt.
  3. Tighten the generator mounting bolts to 17 ft. lbs. (23 Nm).
  4. Install the power steering and the A/C compressor drive belt.
  5. Connect the negative battery cable.

Power Steering Pump Belt
  1. Disconnect the negative battery cable.
  2. Loosen the power steering pump mounting bolts.
  3. Pivot the power steering pump towards the engine in order to relieve the tension on the belt.
  4. Remove the power steering pump drive belt from the pulleys.

To install:
  1. Properly route and install the power steering pump drive belt on the power steering pump and the crankshaft pulleys.
  2. Adjust the power steering pump drive belt to obtain 6-9 mm (0.24-0.35 in) deflection.
  3. Tighten the power steering pump mounting bolts to 22 ft. lbs. (30 Nm).
  4. Connect the negative battery cable.

Posted on Apr 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 1989 jeep wrangler it does not have a serpentine belt but rather 3 belts i need a diagram showing how those belts are suposed to be routed


Check with Autozone and discuss your problem. They know what they are talking about and have always come up with the right parts or belts for me. I used to be a mechanic in my youth and I never go anywhere else.........

Sep 01, 2012 | 1989 Jeep Wrangler

1 Answer

Diagram for 5 pulley belt 98 pontiac transport.


start from bottom crankshaft pulley and ac compressor turn belt tensioner counterclockwise or lift forward then run pulley belt around crankshaft pulley and around AC compressor,run pulley belt around power steering pump then around alternator,once drive belt around alternator you done make sure drive is center of crankshaft pulley and AC compressor pulley.and belt back is center against water pump pulley before releasing the belt tensioner.

Aug 27, 2012 | Pontiac Trans Sport Cars & Trucks

3 Answers

Need diagram for 2001chevyprismserpentinebelt


ledsled378_149.jpg

..............................................................................................................................................

Aug 16, 2011 | 2001 Chevrolet Prizm

1 Answer

How to change the water pump? what has to come off first,second third etc.


I have a 1997 Rodeo so I'm not sure it is the same, but if your waterpump is located under the timing belt cover like mine is and is driven by the timing belt ...

1) Remove the upper fan shroud
2) Remove the (4) nuts then the cooling fan assembly
3) Remove the power steering drive belt
4) Remove the air conditioning compressor drive belt
5) Remove the generator drive belt
6) Remove the fan pulley assembly
7) Remove the crankshaft pulley
8) Remove the oil cooler hose
9) Remove the timing belt cover
10) Remove the timing belt pusher
11) Mark where the timing belt is currently seated in the cam and crankshaft gears (be real sure you know what you are doing here!!!)
12) Remove the timing belt
13) Drain the radiator
14) Remove the waterpump

Mar 01, 2011 | 1999 Isuzu Rodeo

1 Answer

I need a belt routing diagram for a 1994 Jeep Cherokee, 4.0L ,4wd


No diagram but here is how it goes:
Over the power steering pulley, under the idler pulley(backside of belt in contact with pulley) next to the a/c compressor, over the compressor,over the alternator, backside of the belt over the fan pulley, over the crankshaft pulley, backside over the water pump pulley, returning to the power steering.

Dec 16, 2010 | Jeep Cherokee Cars & Trucks

1 Answer

Replace alternator


The alternator belt on the 1999 Dodge Caravan also controls the air conditioner compressor, the water pump and the power steering pump. The belt is called a serpentine belt, and it is designed to fit around all of the accessory pulleys at the same time. As the belt travels around each accessory pulley, it enables the accessory to operate. Once the belt is damaged, cracked or frayed, you should change it before it breaks. If that happens, each of the accessories will stop working.

Open the hood and prop it up so that it does not fall. Engage the parking brake.

Inspect the top surface of the fan shroud for the serpentine belt routing diagram. Follow the routing instructions on the diagram to install the new belt.

Locate the serpentine belt self-adjusting tensioner on the front of the engine. The tensioner is directly below the alternator. Use the bolt that connects the tensioner pulley to the tensioner arm to rotate the tensioner.

Turn the tensioner device counterclockwise to move the tensioner. This will relieve the tension from the belt. Once the belt has enough slack in it, slide the belt out from under the tensioner pulley.

Lift the belt off each accessory pulley. Slide the belt around the fan blades and out of the engine area.

Lay the old belt next to the new belt to ensure that the new belt is the correct width and length. Slide the belt around the fan blades and around the crankshaft pulley on the bottom of the engine.

Follow the belt routing diagram to position the belt around the air conditioner compressor pulley, the power steering pump pulley, the water pump pulley and the idler pulley. Once the belt is routed inside each accessory pulley, inspect the belt to make sure that it is securely inside the pulleys.

Crank the 1999 Dodge Caravan for 10 to 15 seconds to completely seat the belt ribs in the grooves on each accessory pulley. Shut the engine off and close the hood.

If the belt routing diagram for the 1999 Dodge Caravan is missing, use a pen and a notepad to draw the exact routing of the old belt and use it when installing the new belt.

Nov 26, 2010 | 1999 Dodge Caravan

2 Answers

Diagramm serpantine belt 2005 sprinter2500


Hi.

Here the belt routing for 2005 Dodge Sprinter 2005, whch was sold only with the 2.7 engine mounted:



feac688.jpg


Fig. Accessory Belt Routing-A/C Compressor (1), Power Steering Pump (2), Tensioner (3), Crankshaft Pulley (4), Water Pump (5), Alternator (6), Idler Pulley (7)-All Engines

Here a different view:

62bcecc.jpg

Here also the fan belt routing;

729c6e0.jpg

Fig. Fan belt routing-Fan pulley (1), Fan belt (2), Crankshaft pulley (3)-3.0L engine shown

PROCEDURE Removal & Installation


2.7L Engine

1. Loosen the tension adjust and remove the A/C compressor drive belt.
2. Attach a 3 / 8 inch drive ratchet to the automatic belt tensioner.
3. Rotate the belt tensioner counterclockwise to release the belt tension.
4. Remove the accessory drive belt, starting with the water pump pulley.



To install:

1. Position the accessory drive belt around every pulley except the water pump pulley.
2. Rotate the drive belt tensioner clockwise, install the accessory drive belt and release the tensioner.
3. Position the A/C Compressor drive belt over the crankshaft pulley and A/C compressor pulley.
4. Tighten the drive belt tensioner.
5. Ensure the belt is seated properly on all of the pulleys.

If this solution was helpful, then please do not forget to Accept.
Writing dedicate solution, sharing skills, researching and extracting info from service documents takes time, and your feedback is important for us.
If you repute any solution useful, please click on Accept.

All the best.

Ginko.

Sep 21, 2010 | Dodge Sprinter Cars & Trucks

1 Answer

Belt routing diagram 98 zx2 2.0


1) Start with the alternator.
2) Forward to the smooth idler
3) Forward to power steering
4) Down to A/C compressor
5) Back to crank pulley
6) Forward around tensioner
7) Back glancing off of water pump
8) Back glancing off of ribbed idler
9) Up around alternator (where you started)
Good luck!

Sep 11, 2009 | 1998 Ford Escort

2 Answers

Need diagram to install serpentine belt on 2004 Dodge Ram 1500 Hemi


There should be a diagram under the hood on the fan shroud or radiator support. If not, let me know and I see if I can find one. For the most part, if the pulleys it rides on are grooved, the belt ribs ride on it, it the pulley is smooth, the back side rides on it. From a picture of the alternator I have, from the passenger side coming up, over the alternator, then down and under the belt tensioner (smooth pulley), then up and over A/C compressor, then down and around P/S pump, up and around water pump, down around crankshaft pulley.

Jun 03, 2009 | 2004 Dodge Ram 1500

1 Answer

Need diagram of serpentine belt


As this forum will not allow images and the link for my information requires a paid subscription I propose the following: email me at curtisephlush@yahoo.com and I can sen you a document with a belt routing illustration.

Short of that, I can give you a verbal description, but it is sort of confusing:
Top of CAM to top of ALTERNATOR - bottom of ALTERNATOR to top of nearby (front) PULLEY - bottom of PULLEY to top of A/C COMPRESSOR - bottom of COMPRESSOR to bottom of CRANK - top of CRANK to bottom of middle PULLEY - top of middle PULLEY to bottom of rear TENSIONER - top of TENSIONER to back to top of CAM. Remember the serpentine belt has ribs on only one side, the ribs face AWAY from the two guide pulleys and TOWARD the pulleys on the Alternator, Compressor, Crank, Cam and Tensioner. You should tell by the pulley being smooth or ribbed as needed.

Feb 23, 2009 | 2000 Oldsmobile Intrigue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

xxxxxx xxx

Level 3 Expert

4844 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...