Question about Cars & Trucks

1 Answer

My oil pan stuck on 1998 chevy express.ALL 13 BOLTS ARE OUT AND PAN STILL WONT COME DOWN

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 226 Answers

Most of those oil pans were sealed with silicone RTV sealant. First thing to do slam the door on your hand so you will be about half mad .Then drive a screwdriver in between pan and block. You can straighten it later when you get it off. Good luck.

Posted on Jan 02, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing oil pan gasket 1998 chevy silverado 305 cu.in.


REMOVAL PROCEDURE
  1. Remove the oil level indicator tube.
  2. Raise the vehicle.
  3. Remove the engine oil and the engine oil filter.
  4. Remove the oil filter adapter.
  5. Remove the starter.
  6. Remove the flywheel inspection cover.
  7. Remove the engine mount through bolts.
  8. Raise and support the engine.




  1. Remove the oil pan nuts and bolts. Note the location of any studs to assist reassembly.
  2. Remove the engine oil pan and the gasket.
  3. Clean all sealing surfaces. Refer to Oil Pan Clean and Inspect under Engine Unit Repair.
INSTALLATION PROCEDURE


  1. Install the engine oil pan and a NEW gasket. Refer to Oil Pan Installation under Engine Unit Repair.
  2. Lower the engine onto the mounts.
  3. Install the engine mount through-bolts.
  4. Install the starter.
  5. Install the flywheel inspection cover.
  6. Install the engine oil filter and the engine oil.
  7. Install the oil filter adapter.
  8. Install the oil level indicator tube.

May 04, 2015 | 1998 Chevrolet Chevrolet silverado

1 Answer

How to get the tranmission pan unscrewed to change Gasket 1984 chevy c10


If you are going to change the gasket, you should also change the filter at the same time, especially if it hasn't been done recently. You will need a large drain pan to catch oil in because there is no drain plug. Remove the bolts down both sides of the trans pan, 1/2" I believe, and loosen the back ones 3 or 4 turns. Loosen and slowly remove the bolts on the front of the pan because oil will start to drain from there. Once the oil has drained remove the back bolts and drop the pan. clean it out good and check for "stuff". It's normal to see silver filings in the oil but an excessive amount or actual pieces indicate a problem. Two screws should remove the filter. Replace it and put the new gasket on and set the pan in place. Bolt it on. Torque specs for these bolts are 12-13 ft.-lbs for the Turbo 350 and 400. The 700R4 is torqued to 18 ft.-lbs.

If you have trouble getting at the rear bolts on the trans pan, you may need to unbolt the trans mount and lift the tailshaft a little with a jack to get enough room to get it there. Be gentle doing it.Hope this helps.

Sep 25, 2011 | Chevrolet Silverado Cars & Trucks

2 Answers

HOW DO I REPLACE A SHIFT SILENOID IN A 1998 CHEVY VAN 1500


This is on a 4L60-E--Automatic Transmission

michael_cass_182.jpg
This is on a 4L80-E--Automatic Transmission


michael_cass_183.jpgHope this helps you ??

Jun 27, 2011 | 1998 Chevrolet Express

2 Answers

Where is trans filter located


Hi,
The follwoing is from the GM Shop Technical Manual.
Changing the filter requires removing the transaxle oil pan and gasket,
Remove or disconnect

bendarden.jpg

  • Raise vehicle and suitably support.
  • Loosen oil pan bolts and drain fluid,
  • Remove oil pan attaching bolts.
  • Remove pan pan and gasket.
  • Remove the oiil filter using a long screwdriver pry filter neck out of the seal.
  • Check oil filter seal for damage or wear. If needed, remove and replace
Install or connect
  • install new oil filter and/or seal.
  • install the old pan gasket since it can be reused, unless sealing ribs are damaged. If damaged, use new gasket.
  • Install the oil pan and attaching bolts.
  • Tighten pan bolts to 13 lb. ft,
  • Lower vehicle.
  • Refill transxle to proper level with DEXRON III or DEXRON-IIE fluid.
  • Checkoil pan gasket for leaks,

May 21, 2011 | 1995 Buick LeSabre

1 Answer

What is involved with replacing the oil pan on 1998 GMC Sierra?


  • Step 1 Raise the truck using the proper equipment. Use a ramp or a jack and jack stands to support the vehicle securely by following all directions for use provided by this equipment's manufacturer.
  • Step 2 Drain all oil from the Silverado by placing an oil drip pan under the vehicle's engine block, directly under the oil drain plug. The drain plug is located on the oil pan, between the vehicle's tires underneath the vehicle. Use a wrench to loosen and remove the plug allowing the oil to drain into the pain below.
  • Step 3 Notice the various items attached to the oil pan or in the way of the oil pan dropping. For the oil pan to drop, remove the negative battery cable, front differential (only for four-wheel drive vehicles) and the under body shield by using a wrench or socket set.
  • Step 4 Remove the oil pan shield by loosening the four bolts holding it in place along the edges of the shield. Then, remove the cross brace, oil filter, the transmission to oil pan bolts and the oil level sensor.
  • Step 5 Follow the removal of those pieces by removing the bolts from the two front wiring harness, the engine wiring harness retainer, engine oil cooler pipe to oil bolts and the transmission oil cooler pipe retainer using a wrench. Located the closeout covers and bolts located on each side of the engine and remove them.
  • Step 6 Disconnect each of the oil pan bolts using a wrench that will allow the oil pan to drop. The oil pan gasket will also fall off and replacement should occur before reinstalling the oil pan.


  • Read more: How to Drop the Oil Pan in a Chevy Silverado | eHow.com http://www.ehow.com/how_4508109_drop-oil-pan-chevy-silverado.html#ixzz0wi82Ul2u

    Aug 15, 2010 | GMC Sierra 1500 Cars & Trucks

    1 Answer

    I need to remove the oil pan of my 2003 chevy express 1500 i have removed all of the bolts but it is not coming out


    Make sure you have all bolts out. Then gently pry around the edges with as wide a bladed flat screwdriver as you can find. Is this a steel pan, or a cast aluminum pan?

    In any case do not apply very much force in one area, or you risk warping/breaking something.

    May 17, 2010 | Cars & Trucks

    1 Answer

    Ho do you remove oil pan on 1998 chevy malibu 3.1


    take out the oil pan bolts and take it out might have to undue motor mounts and jack up engine to get pan out.

    Oct 04, 2009 | 1998 Chevrolet Malibu

    1 Answer

    How do I change the tranny fluid in my 1998 cadillac catera


    Fluid - A/T: Service and Repair
    Transmission Fluid and Oil Filter Changing
    REMOVAL PROCEDURE
    1. Raise and suitably support the vehicle. Refer to Vehicle Lift Points.
    2. Place drain pan under pan
    3. Remove oil pan bolts from front and sides only.
    4. Loosen the rear oil pan bolts approximately four turns.
    5. Lightly tap the oil pan with a rubber mallet or pry to drain the fluid from main case.
    6. Remove the oil pan bolts from rear oil pan and gasket.
    7. Remove front oil pan bolts leaving one corner bolt in loosely.
    8. Lightly tap oil pan with rubber mallet or pry to drain fluid.
    9. Remove the following remaining components:
    ^ The front oil pan bolts
    ^ The oil pan
    ^ The gasket
    10. Remove the oil filter bolts and filter.
    11. Clean the following components:
    ^ The transmission case
    ^ The front adapter case
    ^ The oil pan gasket surfaces with solvent
    ^ Air dry
    ^ All traces of gasket material must be removed
    INSTALLATION PROCEDURE
    1. Install the gasket.
    2. Install the oil filter.
    3. Install the bolts.
    ^ Tighten the transmission oil filter bolts to 20 Nm (15 ft. lbs.).
    NOTICE: Refer to Fastener Notice in Service Precautions.
    4. Install the front oil pan.
    5. Install the front oil pan gasket
    6. Install the front oil pan bolts
    ^ Tighten the front oil pan bolts to 11 Nm (96 inch lbs.).
    7. Install the following components:
    ^ Install the pan
    ^ Install the gasket
    ^ Install the bolts
    ^ Tighten the oil pan bolts to 11 Nm (96 inch lbs.).
    8. Refill the transmission with DEXRON III through oil pan fill plug on the side of the (main case) oil pan. Fill the transmission to lower edge of oil
    pan fill. Fill plug opening using and oil suction gun.
    ^ Tighten the oil pan fill plug to 45 Nm (33 ft. lbs.).
    9. Lower the vehicle.
    10. Check the transmission fluid level. Refer to Transmission Fluid Checking Procedure.

    Sep 13, 2009 | 1998 Cadillac Catera

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    18 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...