Question about Ford Cars & Trucks

1 Answer

Putting back a dash and instrument cluster. Can someone please help with an electrical wiring diagram for a Ford Econovan 1993 the same as a Mazda Bongo E2000?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Ford Master
  • 946 Answers

Try this site,maybe?
http://www.bbbind.com/free_tsb.html don-ohio (:^)

Posted on Jan 02, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 48 Answers

SOURCE: 1995 Neon Instrument Cluster Wiring Diagram

are you talking about the wires that connect the car harness to the gauge cluster with the 2 big plugs?

Posted on Jul 17, 2008

  • 1 Answer

SOURCE: Instrument cluster went blank

I am currently working on my 92 Deville with the same problem. I was driving along, and smelled what I felt was a smoking printed circuit board. I looked down, and the digital fuel data center and climate control panel were dark.

I have the factory shop manual, and with the aid of a meter and the manual, I traced the problem to a bad BCM. The 16v supply coming from the BCM was gone. Opened up the BCM and found an overheated transistor. I also removed the fuel data center and the Climate control panel. The fuel data center panel did not smell good. I found a shorted capacitor on the Fuel data center circuit board. I am replacing the capacitor, and will be picking up a used BCM at the boneyard tomorrow. I might also have an overheated wire in a cable that might have to be replaced. I have not gotten that far in the troubleshooting yet.

Good luck with your problem.......

Posted on Oct 04, 2008

  • 193 Answers

SOURCE: VW Polo Dash Instrument's

buy a repair manuel from a parts store. Check to see that it has the wiring diagram in the manuel.

Posted on Nov 22, 2008

  • 1 Answer

SOURCE: hi in need of a wiring diagram fuse box Mazda bongo

look here: http://www.bongoforum.co.uk/forum/Blah.pl?

Posted on Dec 06, 2009

  • 27 Answers

SOURCE: mazda bongo manual

there is a bongo owners site, try them

Posted on Feb 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an 01 Pontiac Azteca the problem is everytime I put the car in gear it shuts the dash lights and radio light off, any idea what could cause this?


A bad or lose ground ! Checking a wiring diagram would show if these thing's share a common ground . Transmission , instrument cluster lighting an the radio lights up with the instrument cluster . You can go onto youtube an check out videos on how to read a wiring diagram , how to do voltage drop testing , basic automotive electrical circuit testing . Then you could go to http://bbbind.com/free_tsb.html free wiring diagrams an test the instrument panel back lighting circuits ! You will need a DVOM - digital volt ohm meter an you will more then likely need to take parts of your instrument panel apart . Your probably better off taking your vehicle to a qualified repair shop .

Aug 04, 2016 | Pontiac Cars & Trucks

1 Answer

Dash lights /on 1993 ford taurus


remove steering column plastic set seat all the way back remove linkage indicator line(little wire cord to stering column on a hook) under dash remove the molding from stereo to driver door remove dash cluster look for cluster lights replace...reverse process...

Apr 07, 2013 | 1993 Ford Taurus

2 Answers

Dash lights work but no gauges in my 1994 dodge intrepid!! i have checked every fuse i can find in the dash and under the hood but they still won't work, they don't even flicker when i turn my key....


If you have a 1993-1995 Intrepid and you have a check engine light, you can find out what the codes are by following this process:
To obtain fault codes using the MIL (Check Engine Light):

1. Cycle ignition key to ON, OFF, ON, OFF, ON within 5 second (do not actually crank engine!!)

2. Count the number of times the MIL on the instrument panel flashes on and off. The number of flashes represents the trouble code. There is a slight pause between the flashes representing the first and second digits of the code. Longer pauses seperate the individual two digit trouble code.

Example:
Lamp flashes 4 times, pauses, then flashes 6 more times. This is an indicates a DTC of 46.

3. Lamp will always flash 55 at the end of the test. This signals the end of the test.

You have put the computer in diagnostic mode and it will now display any codes that have been stored in memory. Each code will refer to a symptom your car is feeling.

Here is a list of all codes that can be displayed and what they mean:

http://www.automotiveforums.com/t355082-trouble_codes_for_all_intrepids_1993_2004.html

Post Back With A Code, If you get one.
I Hope this Helps,
Jos
jtobias1020@gmail.com

CHECK OUT THIS ARTICLE! CLICK ON THE LINK AT THE BOTTOM
I Know Yours is A 94' , They didnt change to much in two years. 1993 Dodge Intrepid instrument panel

JB DRUMLIN
  • 1993 DODGE INTREPID
Electrical problem
1993 Dodge Intrepid 6 cyl Two Wheel Drive Automatic

All five guages of the instrument panel do not work.
ie: speedometer
gas guage
temperature guage
automatic quadrant selector
rpm guage
62217_left_ground_1-wjx2pyzwokz1jy5symyt5vs3-3-0.jpg


62217_right_ground_1-wjx2pyzwokz1jy5symyt5vs3-3-2.jpg

After reading through the Article, Pop the Hood and Check out the Grounding Locations. Look for any wire that looks like it should go somewhere. Screw it down (Ground) to the Frame Rail.
First Disconnect the Negative from Battery For a couple Minutes,
If the Engine was replaced they mighta missed a couple Grounds.
One is front Driver corner by the Battery
Two is on Passenger Corner.

1993 Dodge Intrepid Instrument Panel Electrical Problem 1993

I have a feeling there is a Loose Ground or an open, There should be 5-6 Volt Reading coming out of the Cluster,
Let me know how All this goes.
Jos

Feb 28, 2017 | 1994 Dodge Intrepid

1 Answer

We have a 1993 Mitsubishi Eclipse 1.8 and we replaced the interior, dash, and instrument cluster. Everything was fine except the instrument panel would not light up. Connections were checked and a few were...


Found this wiring diagram. Voltage for the coil comes from ignition switch, the ignition power transistor/ignition module controls the ground for the coil. My info says you crank and cam position sensors are built into the distributor. Sorry, I know very little about a Mitsubishi, I can't help you diagnose.
distributor-wpygdvvrrzigndzxeznsbtvk-1-0.jpg

May 11, 2017 | 1993 Mitsubishi Eclipse

1 Answer

99 Ford Escort ZX2 Speedometer/Odometer doesn't work


I'm sorry, I have to ask, this is an automatic right? That out of the way, Does the trans shift different when you drove it with the Vss unplugged when you had the ohm meter on it? 8.5 volts? Something sounds wrong here. I'll have to look up the wiring diagram before I can say thats a bad reading but it should be battery voltage (14 volts running) or 5 volts?

Jul 08, 2010 | 1999 Ford Escort

1 Answer

1992 ford escort wiring diagrams


I have the instrument cluster diagrams, need an email address to send to in pdf format

Feb 10, 2010 | 1992 Ford Escort 4 Door

1 Answer

I have a 1975 F100 Custom 2 wheel truck. Am having trouble with the dash fuel gauge, its not working. I have checked all the fuses under the dash. I have tried to ground the fuel sending wire out to see if...


well have problems with the voltage regulator on back of the instrument cluster..... no power to the guage it self... if good then check sending unit in tank.. also make sure copper float on sending unit is not full of gas,.. they get pin holes then fill with gas and dont float....because you ground the wire and no change.. i would start with instrument cluster

Sep 04, 2009 | Ford F-100 Cars & Trucks

2 Answers

Ford econovan


this would definitely be the relay and you would have to chase the wire from the light or the steering column to find out exactly. I don't know much about this van or else i would be able to tell you where it is located. sorry

Feb 28, 2009 | 1999 Ford Econoline

1 Answer

Brakes not working


Every thing you need to find for the brakes is under the dash.Easiest way to work on the parts is to remove the instrument cluster(gauges)Its been a while since last did one but part of the dash surround may also have to come off.Let me know if you need more help

Nov 23, 2008 | 1985 Ford Econoline

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...