Question about Cars & Trucks

Open Question

Selector switch for air flow floor dash or defroster

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: air flow selector

Your mode door is controlled by vacuum check the vacuum hose on the left side of the intake manifold. these some times fall off leaving your mode door with no vacuum and the default position of the mod door is defrost.

Posted on Jun 18, 2008

SOURCE: 2004 Ford Crown Victoria no air flow through main air vents

Chances are the electronic/digital HVAC control unit is bad. This same problem happened to me and I had to replace the entire unit. The dealer wanted to charge $800 for just the part! After I freaked out on them, they found a used one for less than half. Sorry, but there's no easy fix here.

Posted on Jul 19, 2008

  • 1 Answer

SOURCE: There is no air flow

You need part GM Part number 89018675 or ACDelco 15-73596. The Mode Selector Actuator. What happens is the part is a CHEAP part POORLY designed and when it goes to turn the flaps inside the HVAC unit its the plastic gear slips instead of turning the flap!!!

Just to forward you you might want a deal to install this art for you unless your good at fixing your own vehicle, because you need SMALL sockets and a lot of patience to get this part in!!!

The part is ALMOST directly above the steering shaft for your steering wheel, so theres a lot you got to remove before you will even see them!!!

I only recommend you to have a dealer put this part in for you, unless you have your own service manual!!

Because there is 5 of these darn things and if you pick the wrong one you will have to do it all over again!!!

3 on the Drivers side and 2 on the Passengers side!!

But replacing this part SHOULD solve all your problems!! AS it did for me and i was having the same issues as you have described!!


Posted on Jul 22, 2008

  • 1 Answer

SOURCE: No dashboard heat output

The climate control was poorly designed on these cars.

There is only heat on the floor and defrost settings, due to the layout of the ductwork.

Posted on Nov 22, 2008

philriden
  • 146 Answers

SOURCE: 1998 Mustang - AC blows only through Defrost vents

You probably have a vacuum leak on the passenger side. its a small plastic hose some times they come unpluged from the engine. or brake.

Posted on Jan 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need pitcure of vaccum lines on 1999 Ford Ranger v6 3.o air and heat blows only threw the defroster.


26392097-cvaukpwazi2vnl4fgradjhua-2-2.gif

Item Part Number Description 1 18A318 Vacuum Control Motor-, Panel/Defrost Door 2 18A478 Panel/Defrost Door (Full Vacuum Position) 3 - Defrost Air Flow 4 - Side Window Demister Air Flow 5 18B545 Temperature Blend Door (Full Heat Position) 6 19860 A/C Evaporator Core 7 19A813 Air Inlet Duct Door (Full Vacuum Position) 8 - Outside Air Inlet 9 18A318 Vacuum Control Motor-, Air Inlet Duct Door 10 - Recirculated Air Inlet 11 18527 Blower Motor 12 19A566 A/C Vacuum Reservoir Tank and Bracket 13 - Vacuum from the Engine Intake Manifold 14 19B888 A/C-Heater Function Selector Switch 15 - Vacuum to the 4x4 Hub Solenoids 16 18495 Water Diverter Valve (Full Vacuum Position) 17 18476 Heater Core 18 18A559 Floor/Panel Door (Full Vacuum Position) 19 - Floor Air Flow 20 18A318 Vacuum Control Motor-, Floor/Panel Door 21 - Panel Vent Air Flow

Dec 09, 2016 | Ford Ranger Cars & Trucks

1 Answer

Why does turning vent knob (defrost, mix, dash,floor,etc.) have no effect?


Vent Type Selector Not Working - Jeep Wrangler Forum

www.wranglerforum.com/.../vent-type-selector-not-working-117541.ht...

Oct 13, 2011 - 30 posts - ‎21 authors
It will not switch into upper vent mode, only have the option to have it all on my ...You mean the switch itself on the dash will not turn physically?

Turning vent knob (defrost, mix, dash,floor,etc.) has no - Fixya

www.fixya.com/cars/t26033235-turning_vent_knob_defrost_mix
Turning vent knob (defrost, mix, dash,floor,etc.) has no effect. Posted by Jim Long on Jan 01, 2016. Want Answer 1. Clicking this will make more experts see the ...

a/c problem fixed - ChevyTalk - FREE Restoration and Repair Help ...

www.chevytalk.org/fusionbb/showtopic.php?tid/27558/tp/1/cto...id/...
3) Mode of operation knob has no effect (air comes only to floor for example) 4) Rear defog ... The transistor is MPSA56 (bipolar pnp) and you can locate the faulty one easily. It is the .... With the switch turned only to Vent, no air from anywhere?

Climate vent knob not working [Archive] - VW GTI Forum / VW Rabbit ...

www.golfmkv.com > ... > DIY + Maintenance + Tips/Tricks

Jan 01, 2016 | Cars & Trucks

1 Answer

Why wont my 2001 ford windstar blow out of vents ? only on defrost?


Air Flow Control
Air flow control is accomplished in the following manner:
  • Primary control is through the function selector knob , mounted on the heater function selector switch, which is part of the heater control .
  • The function selector knob has the following positions: OFF, PANEL, PANEL/FLOOR, FLOOR, FLOOR/DEFROST and DEFROST.
  • The heater function selector switch combines a vacuum selector valve with an internal electrical switch.
  • The vacuum selector valve directs source vacuum to various vacuum control motors (18A318) . Refer to the System Airflow Schematic and Vacuum Control Charts.
  • An internal single-pole electrical switch is also controlled by the selector. The switch controls the electrical supply to the heater blower motor switch (18578) .
  • The position of the function selector knob determines the manner in which the system will operate.
  • Each position of the function selector knob is detented for positive engagement.
  • You probably have a vacuum leak , Pull heater control panel an check for vacuum . A broke vacuum hose or The vacuum selector valve is bad ! Or check for a vacuum hose in the engine compartment being off somewhere !

Mar 08, 2015 | 2001 Ford Windstar

1 Answer

Why is hvac air coming from all three locations (vent/floor/defrost) regardless of switch setting?


Check air box if it won't change air flow some thing is wrong there inside the car

Jul 14, 2014 | 2000 Buick Regal LS

1 Answer

Climate Control - Heat and cool work fine. Air flow is directed to defrost /floor. No indication (Sound or sight) that the vacuum diaphrams are being activated. The display on the dash matches the...


Does your vehicle have manual or automatic climate control ? You system is stuck in floor an defrost mode ?

03 mercury grand marquis hvac air flow .-13qahwfdndst2y1hypmr2cdq-4-0.gif Item Part Number Description 1 18A318 Vacuum control motor-floor/defrost door 2 - Defrost air flow 3 18A478 Floor/defrost door 4 18476 Heater core 5 19860 Evaporator core 6 19805 Blower motor 7 - Outside air inlet 8 19A813 Air inlet door 9 18A318 Vacuum control motor-air inlet door 10 - Recirculated air inlet 11 18B545 Temperature blend door 12 18A559 Panel door 13 - Panel air flow 14 18A318 Vacuum control motor-panel door 15 - Floor air flow 16 - Vacuum from the engine intake manifold 17 19A563 A/C vacuum check valve 18 19A566 Vacuum reservoir tank and bracket 19 19980 EATC control
Pull the control panel an check for vacuum

vacuum lines hvac 03 grand marquis-13qahwfdndst2y1hypmr2cdq-4-2.gif Item Part Number Description 1 White Air inlet door 2 Yellow Floor/defrost door 3 Red Floor door 4 Blue Panel door 5 Black Source vacuum 6 - Not used


VACUUM APPLICATIONS CHART-ELECTRONIC AUTOMATIC TEMPERATURE CONTROL Switch Port Vacuum Harness Hose Color Func- tion Manual Override Selector Buttons OFF MAX A/C NORM A/C VENT FLOOR FLOOR/ DEF DEF 1 White Air inlet 2 Yellow Floor/ panel (partial) 3 Red Full floor 4 Blue Panel 5 Black
Source

May 21, 2017 | 2003 Mercury Grand Marquis

1 Answer

Air flow to defrost or floor not switching stays on dash vents


cannot switch from defrost to panel airflow 2001 chevy silverado

Oct 06, 2009 | 2001 Chevrolet Silverado

1 Answer

My AC air registers only have air coming out of the defrost ducts


In every car, there are fins or flaps inside the dash that rotate that distributes the air flow from the blower to the desired opening, ie defrost, floor etc... This flap is controlled by a linkage which is connected to the selector switch. It may be the linkage is no longer connected, or the fins inside the dash are stuck. If the selector switch moves freely with little or no resistence its possible the linkage is no longer connected, otherwise the flaps need to be physically looked at.

Aug 09, 2009 | 1989 Ford F 150

1 Answer

Climate control system only blow air out defrost vent


there is a good chance that you blend air door is stuck closed over your heater core and therefore not allowing the heat to flow, also your door that opens and close your direction of flow from the floor ,das,vent and defrost.your going to have to remove the lower cowling of the dash on the passenger side analso some of the center dash to actually check to see if the cable,servo motors. are acuating the doors.the issue could be just a stuck door or a misaligned cable or that it came off. that falls under the mechanical side of probabilities. electrical would most likely be a faulty selector switch or a servo motor

May 15, 2009 | 2002 Ford Expedition

1 Answer

HVAC vent selector does not function. Air flow is


THe blend door seems to be stuck. When you change settings from defrost to floor air or, vent, the blend door opens and closes directing the air to the place you want it to go to. I have had some success spraying a lubricating oil such as WD40 under the dash on the blend door. You need to get under the dash with a flashlight to locate it. It looks like a flap. Spray it with a couple of shots of the WD40. Go easy on the spraying as you may be inhaling the fumes. Keep the doors and windows open to minimize the fumes. Wait about 1/2 hour and try the A/C functions. (defrost, floor, vent air)

Mar 09, 2009 | 2002 Buick Rendezvous

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...