Question about Cars & Trucks

Open Question

Wire harness diagram for the blower heater - Cars & Trucks

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 34 Answers

SOURCE: 7 wire harness going to blower motor resistor

There is an updated resistor/connector package. Very expensive from GM, try your local NAPA or other parts supplier for a replacement

Posted on Jul 09, 2009

  • 2 Answers

SOURCE: lost my heater/blower all together...got nothing

u need a new blower motor, just replace mines last winter

Posted on Dec 03, 2011

  • 61 Answers

SOURCE: need to know wire color for heater fan blower motor

my guess is green with white stripes and dark grey

Posted on Sep 12, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 kia spectra color code ignition switch diagram pdf


PART COLOR LOCATION 12 VOLT CONSTANT WHITE/BLACK (+) and WHITE (+) IGNITION SWITCH HARNESS STARTER RED (+) IGNITION SWITCH HARNESS STARTER 2 N/A IGNITION 1 YELLOW (+) IGNITION SWITCH HARNESS IGNITION 2 N/A IGNITION SWITCH HARNESS IGNITION 3 N/A ACCESSORY/HEATER BLOWER 1 BLUE (+) IGNITION SWITCH HARNESS ACCESSORY/HEATER BLOWER 2 GREEN (+) IGNITION SWITCH HARNESS

Dec 27, 2011 | 2002 Kia Spectra

1 Answer

How to change blower motor in. 99 grand Cherokee


Check this procedure...Blower Motor Resistor and Controller Replacement


REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.


INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

zjlimited_1958.jpg


Hope this helps (rerember to rating this and leave a testiomonial).

Sep 30, 2011 | 1999 Jeep Grand Cherokee

2 Answers

My heat has stop blowing. replaced blower, and heater on off switch. what else could it be?


LX? DX? EX? Hatchback? sedan? wagon?coupe? engine size? did you check the fuse? Fuse #19, 30 amps in the auxilary fuse box (your owners manual may show the location ,it may be near the blower ?). The Blue/White wire at the heater blower motor should be HOT (12v) with key on. If you ground the Blue/Black wire the motor should run full speed.

Dec 17, 2010 | 1991 Honda Civic

1 Answer

How do i change blower motor resistor on 99 jeep grand cherokee


Welcome to FIxYa.com



Blower Motor Resistor and Controller Replacement

Image Blower Motor Resistor Or Controller/Power Module Remove/Install

REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.

INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

leedavidian_45.jpg



Thank you for using FixYa.com

Regards, Lee Davidian

Nov 22, 2010 | 1999 Jeep Grand Cherokee

1 Answer

Diagram for the placement of the fan blower motor in a 2003 Dodge ram 1500 truck


From autozone.com
2003-04 Vehicles

CAUTION On vehicles equipped with airbags, disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the battery negative (ground) cable, then wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to take the proper precautions could result in an accidental airbag deployment, possible personal injury or death.

NOTE The blower motor is located on the passenger side of the vehicle under the instrument panel. The blower motor can be removed from the vehicle without having to remove the HVAC housing.
  1. Disconnect and isolate the battery negative cable.
  2. Disconnect the wire harness connector from the blower motor.
  3. Remove the three screws that secure the blower motor to the HVAC housing.
  4. Remove the blower motor from the HVAC housing by rotating and tilting the blower motor as needed for clearance.
  5. b8492c4.gif

Fig. View of the resistor block screws (1), blower motor resistor (2), resistor block wire connector (3), blower motor screw (4), blower motor (5), blower motor wire connector (6), blower motor screw (7), HVAC housing (8), wire harness retainer (9), blower motor screw (10)

    To install:
    1. Align and install the blower motor into the HVAC housing.
    2. Install the three screws that secure the blower motor to the HVAC housing. Tighten the screws to 20 inch lbs. (2.2 Nm).
    3. Connect the wire harness connector to the blower motor.
    4. Reconnect the battery negative cable.

Sep 23, 2010 | Dodge Ram 1500 Cars & Trucks

1 Answer

Looking to put remote start and bypass module in 2007 saturn vue need wiring diagram


12 VOLT CONSTANT ORANGE (+) IGNITION SWITCH HARNESS STARTER YELLOW(+) IGNITION SWITCH HARNESS STARTER 2 N/A IGNITION 1 PINK(+) IGNITION SWITCH HARNESS IGNITION 2 N/A IGNITION 3 N/A ACCESSORY/HEATER BLOWER 1 ORANGE (+) IGNITION SWITCH HARNESS ACCESSORY/HEATER BLOWER 2 N/A KEYSENSE LIGHT GREEN (-) See NOTE *1 IGNITION SWITCH HARNESS PARKING LIGHTS ( - ) N/A PARKING LIGHTS ( + ) BROWN (+) @ BCM, PIN B10, GRAY 24-PIN PLUG, See NOTE *2 POWER LOCK RED/BLACK (TYPE A) @ BCM, PIN A8, 16-PIN GRAY PLUG, See NOTE *2 POWER UNLOCK ORANGE/BLACK (TYPE A) @ BCM, PIN A7, 16-PIN GRAY PLUG, See NOTE *2 LOCK MOTOR WIRE GRAY (+) IN DRIVERS DOOR HARNESS DOOR TRIGGER See NOTE *3 @ BCM, PINK 24-PIN PLUG, See NOTE *2 8957_VUE_(-) NEGATIVE DOOR PIN ISOLATION CIRCUIT.pdf DOMELIGHT SUPERVISION WHITE (-) @ BCM, PINK 24-PIN PLUG, PIN A1, See NOTE *2 TRUNK RELEASE N/A SLIDING POWER DOOR N/A HORN BLACK (-) @ BCM, PIN B2, PINK 24-PIN PLUG, See NOTE *2 TACH ANY WIRE NOT PINK or RED @ IGNITION COIL WAIT TO START LIGHT N/A BRAKE LIGHT BLUE (+) @ SWITCH ABOVE BRAKE PEDAL FACTORY ALARM DISARM DISARMS with FACTORY REMOTE ONLY ANTI-THEFT YELLOW (+), ORANGE/BLACK (-) and RED/WHITE (Not used) GM's PASSLOCK 2 System, these wires exit the Ignition Switch Tumbler together and are in the Main Ignition Switch Harness in the Column.

Feb 27, 2010 | 2007 Saturn VUE FWD 4

1 Answer

I need to know what each color means on my distributor???


Review this guide as reference; this Electrical Schematic Diagram applies for 1994 Accord Coupe series of model. Here you will find complete explanation about electrical system of the vehicle. Started from Troubleshooting (tips and precautions) on handling the electrical system, in this manual you will be guided step by step examining each electrical component installed and its connection for example in Wire Harness and Ground Location, started from Engine Compartment, wiring harness is shown from engine ground cable, starter cable, and battery ground cable.

These 359 pages of pdf.fieltype manual is divided into some sections which are Wire Color Code, Relay and Control Unit Location, Wire Harness and Ground Location, Air Conditioning System Circuit, Anti-lock Brake System, Battery, Blower Control, Charging System, Cruise Control, Fan Control, Fuel Pump, Fuses, Ground Distribution, Heater Control, Ignition System Control, Lighting System, and etc.
Download the complete 1994 Accord Coupe Electrical Schematic Diagram here.

You can also find complete workshop manual of 1994 Accord Coupe here.

Pass: freepdfmanual.com

Good luck.

Sep 21, 2009 | 1997 Honda Accord

3 Answers

I HAVE AN 06 H3 HUMMER the heater was blowing fine when I shut the car off ok, when I got back in and started it the heaters blower stopped. I have checked all fuses and relays and they are fine I even...


check the blower speed control, it most likely burned out, also jump battery power direct to the blower and see if it runs, if it does the speed control is defective, if it doesn't the blower motor is toast.

Jan 16, 2009 | 2008 Hummer H3

1 Answer

Need diagram for 2007 escape audiophile


if it is the wiring diagram for the Escape you need, here it is:

12 VOLT CONSTANT Connect to BATTERY ONLY STARTER TAN/LIGHT BLUE (+) IGNITION SWITCH HARNESS STARTER 2 N/A IGNITION 1 LIGHT GREEN/PURPLE (+) IGNITION SWITCH HARNESS IGNITION 2 N/A IGNITION 3 N/A ACCESSORY/HEATER BLOWER 1 BLACK/LIGHT GREEN (+) IGNITION SWITCH HARNESS ACCESSORY/HEATER BLOWER 2 N/A KEYSENSE N/A PARKING LIGHTS ( - ) WHITE/BLACK (-) @ SJB, Connector E, Pin 4, See NOTE *1 PARKING LIGHTS ( + ) BROWN (+) @ SJB, Connector C, Pin 19, See NOTE *1 POWER LOCK PINK/WHITE (1-Wire System) See NOTE *2 @ SJB, Connector D, Pin 22, See NOTE *1 POWER UNLOCK Same wire, See NOTE *2 See DIAGRAMS DOOR TRIGGER PINK (-) @ SJB, Connector C, Pin 28, See NOTE *1 DOMELIGHT SUPERVISION USE DOOR TRIGGER TRUNK RELEASE N/A SLIDING POWER DOOR N/A HORN YELLOW/LIGHT GREEN (-) @ SJB, Connector A, Pin 14, See NOTE *1 TACH NOT RED or WHITE/RED @ IGNITION COIL or FUEL INJECTOR WAIT TO START LIGHT N/A BRAKE LIGHT GREEN (+) @ SWITCH ABOVE BRAKE PEDAL FACTORY ALARM DISARM DARK BLUE/LIGHT GREEN (-) @ SJB, Connector D, Pin 3, See NOTE *1 ANTI-THEFT FORD'S SECURILOCK ANTI-THEFT TRANSPONDER SYSTEM TRANSPONDER @ IGNITION SWITCH TUMBLER EXTRA INFORMATION NOTE *1 The SJB (Smart Junction Block) is the FUSE/RELAY BOX on the PASSENGER SIDE of the CENTER CONSOLE. NOTE *2 This vehicle uses a 1-Wire Door Locking System, LOCK requires a (-)Negative thru a 1000 Ohm Resistor and UNLOCK requires a straight (-)Negative

Jan 06, 2009 | 2005 Ford Escape

1 Answer

Durango vent blower fan


The blower motor resistors are known for going bad. Usually its because the blower starts drawing too much current. What I would recommend doing if you can and have the tools, is to check the blower motor connector to make sure 12 volts is present. If so than I would recommend replacing the blower motor resistor. Then if the same issue ever happens again and the blower motor resistor is bad again, you will need to replace the blower motor and the blower resistor as the final repair.
Here is some info about testing the resistor using a multimeter it you have one:

DIAGNOSIS AND TESTING- BLOWER MOTOR RESISTOR WARNING: ON VEHICLES EQUIPPED WITH AIRBAGS, DISABLE THE AIRBAG SYSTEM BEFORE ATTEMPTING ANY STEERING WHEEL, STEERING COLUMN, OR INSTRUMENT PANEL COMPONENT DIAGNOSIS OR SERVICE. DISCONNECT AND ISOLATE THE BATTERY NEGATIVE (GROUND) CABLE, THEN WAIT TWO MINUTES FOR THE AIRBAG SYSTEM CAPACITOR TO DISCHARGE BEFORE PERFORMING FURTHER DIAGNOSIS OR SERVICE. FAILURE TO TAKE THE PROPER PRECAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL INJURY.
Both the front blower motor resistor and the optional rear heater-A/C unit blower motor resistor can be diagnosed using the procedure that follows. For circuit descriptions and diagrams, refer to Air Conditioning/Heater in Group 8W - Wiring Diagrams.
  1. Disconnect and isolate the negative battery cable.
  2. Disconnect the wire harness connector from the blower motor resistor block.
  3. Check for continuity between each of the blower motor switch input terminals of the resistor and the resistor output terminal. In each case there should be continuity. If OK, repair the wire harness circuits between the blower motor switch and the blower motor resistor block or blower motor as required. If not OK, replace the faulty blower motor resistor block.
Here is the information on replacing the resistor:

REMOVAL
  1. Disconnect and isolate the battery negative cable.
  2. From the passenger foot well area, remove the two hex screws used to secure the blower motor resistor.
  3. Unplug the front blower motor resistor from the wire harness connector.
  4. Remove the front blower motor resistor from the HVAC unit.
Here is an exploded view of the HVAC box. The resistor is #63 in the picture and the actual part may appear slightly different:

spacer.gif 1100_024_0003.gif spacer.gif spacer.gif View Full Image spacer.gif


If any issues such as no voltage at blower connector or damaged or melted connector at the resistor then let me know.

Oct 19, 2008 | 2002 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...