Question about Jeep Cars & Trucks

1 Answer

2002 jeep grand quick shifts into 2 and 3 gear i made sure the tv cablebis hooked up

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

Happy new year !
A/T are complex beasts.
scanning it first, to see if the TCM brain is happy is #1
If it sees and error , that be like super important , right?
please tell all that works and not with said A/T
the good, the bad and the ugly, is what matters
the service manual covers this, called a test drive.
too quick upshift to 3.
the TCM uses many inputs to decide this, not JUST the TV.cable.'

1: ECM reported engine load. to TCM.
2: speed (speed sensors)
3: TV cable sure (when present)
4: TPS throttle angle. later years, #3 is deleted and only this is it.
scan it. You do or they do.
on all cars with TCM you must do that. or work blind.

Posted on Jan 01, 2017


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2002 jeep quick shifts into 2 and 3 gear I made sure the TV Cable is hooked up

double posted, why. then left of cars name. 02 WJ
please add to 1st post, add comments to it for best service.
the TV need to work not just be hooked up
the valve on the end must not be stuck out
or the cable rusted,
or adjusted wrong.
and you need to scan the PCM

is this a USA jeep
with gas engine?
not diesel.
WG not.
42RE trans?
545RFE trans
both are TCM brain shifted, moving,.
and have many inputs that can fail..

scan it.
see P07xx codes, all are transmission, and key to what's UP.

Jan 01, 2017 | Jeep Cars & Trucks

1 Answer

Jeep 2002 Grand laredo have delay shifting gear

Have you checked the trans fluid? Has to be checked with engine running in neutral. If its good you will need to bring it to a transmission shop. Good luckHowie

Apr 20, 2012 | 2002 Jeep Grand Cherokee

1 Answer

2005 Jeep Grand Cherokee Limited will not go into gear. What should I try?

try looking where the gear shift hooks to the transmission. it may have come loose. good luck

Dec 01, 2010 | 2005 Jeep Grand Cherokee

1 Answer

Shift solenoid A electrical

my 2002 jeep grand cherokee is stuck in what i think is 3rd gear runs smooth only at 45 to 50 miles an hour what?

Nov 05, 2010 | 2002 Jeep Grand Cherokee

1 Answer

My jeep won't shift out of 1st gear

bad shift silonoid or possibly the pressure sensor,also could be a clogged filter.

Apr 14, 2010 | 2002 Jeep Grand Cherokee

1 Answer

Eratic shifting of gears at speeds of 55 to 75

I would check the transmission fluid level and color, should be a nice clear red color. You may need to have the filter replaced. Possibly some internal transmission problem also.

Mar 11, 2010 | 2002 Jeep Grand Cherokee

1 Answer

2001 Jeep Grand Cherokee won't shift out of first gear and the fault codes are P0733 and P0734.

P0733=Gear 3 Incorrect Ratio
P0734=Gear 4 Incorrect Ratio,
your transmission is in "limp" mode,
Have the following sensors checked on the transmission,input sensor,output sensor,and speed sensor.
The transmission is not getting a signal from one of them,So it doesn't know how fast your going so it doesn't up shift.

Jan 22, 2010 | 2002 Jeep Grand Cherokee

1 Answer

I have a Jeep Grand Cherokee 2001 with 88k on it . It feels as if it is holding on to 1st gear to long when shifting to 2nd and the same when shifting from 2nd to 3rd. The slam isnt as hard when going to...

as a quick remedy 1st check your fluid make sure is clean and leveled/adjust your kick down cable for early shifting by loosening the cable till you establish the right shifting

Jan 13, 2010 | 2001 Jeep Grand Cherokee

3 Answers

Audible knocking in rear of 1993 jeep grand cherokee laredo with 150,800 miles knocking only occurs when accelerator is not pressed

Sounds as If You Have A Chipped Tooth On the "RING GEAR" in the Differential (Rear Alex).
Is this Where You Hear The Noise Coming from? If So Remove Diff Cover With One Wheel OFF The Ground Trans In Neutral Rotate Drive Shaft and Look Closely For ANY Abnormal Surface on EACH Tooth of RING GEAR= the Large one And The "PINION GEAR" the Small one. If you find Chip or Rough spot Diff Must Be Rebuilt. Beyond that A Pinion Bearing can Also Make A Knocking Noise But the "GEARS" Will Be a Rhythmic Noise. I Hope this is of Some Help To You Good Luck !!

Jun 03, 2009 | 2002 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

78289 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides