Question about Cars & Trucks

Open Question

I want to check my balances. Please do not answer Fantastic, when the answer is anything but. It's noting but a long, long wait.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2002 aztek in the shop with a leak in the intake manifold gasket. the mechanic wants to also remove the heads and check and balance them. this increases the bill by about 500 bucks. should this be...


never heard of check and balance a head. I would ask him what he's trying to fix. What were your symptoms/reasons for pulling the intake manifold?

Sep 28, 2010 | 2002 Pontiac Aztek

1 Answer

Volvo 740 gl 1988 b230f automatic 4 speed transmission....Strange vibration at 50 to 90 kmh...


You don't give any details about the vibration, you know what "strange" means but the rest of us have to make a guess.

The most likely cause is that the wheels are out of balance. This can happen if you've recently struck a kerb or pothole, if an existing balance weight has fallen off, if you have recently removed a wheel and refitted it, or if you've had a tyre repaired or replaced without having the wheel rebalanced afterwards.

There are many other potential causes, but getting the wheel balancing checked and adjusted is the cheapest and easiest thing to start with. Get the balancing checked and then report back if the problem is not resolved.

Please don't forget to rate my answer.


Feb 21, 2010 | 1989 Volvo 740

1 Answer

The door cover for the fuses is missing.need to know which fuse amp. goes in what spot...can't see my fuel reader. (don't know how much gas I have).


Not a fantastic answer but Try 10 amps in them all one by one until the fuel gauge works, Wont harm anything that way.

You really need the diagram!

Jan 17, 2010 | 1988 Cadillac Sedan DeVille

1 Answer

Car shimmies at 60 mph


Hello. Most likely you have an out of balance or out of round tire. A simple way to check tire balance - if the shimmy is present at one speed and not present at another speed, then you most likely have a tire out of balance [sometimes the tire balancing weight[s] can fall off. An out of round tire or bent rim usually shimmies at all speeds and replacement of the tire or the wheel is the only fix.
Begin by driving to a reputable tire store and have them check your tires, a free service in most instances. IF it is not a tire, it could be that you need a front end aligmnent.
Regards, Joe
PS please rate my answer. Thank you and happy holidays.

Dec 26, 2009 | 2002 Chevrolet Tahoe

1 Answer

I need to replace my timing belt on my hyundia elantra 2003 with 1997 cc engine


Dear Friend
Removal: Support engine: remove -engine mounting, auxiliary drive belt, water pump pulley, crankshaft pully bots & crankshaft pully, timing belt covers....turn crankshaft to TDC on No 1 cylinder, ensure crankshaft sprocket, camshaft sprocket, oil pump sprocket & balancer shaft sprocket timing marks lighned. Pls note: Timing marks on camshaft sprockets should align with cylinder head uppter face, dowl pins on camshaft sprockets should face downwards....Slacken tensioner botl. Move tensioner away from belt & tighten bolt.
Remove: automatic tensioner unit bolts, automatic tensioner unit, timing belt, crankshaft bolt, crankshaft sprocket, crankshaft sprocket guide washer...slacken balancer shaft belt rensioner bolt, move tensioner away from belt & lightly tighten bolt...Remove balancer shaft belt.

Installation:
ensure timeing marks aligned.Note: Timing marks on camshaft sprockets ahould align with cylinder head upper face, exhaust sprocket mark is on recess but inlet sprocket mark is on tooth. To check oil pump sprocket positionded sorrectly: remove blanking plug from cylinder block, insert 8mm diameter Phillips screwdriver in hole. ensure screwdriver is inserded 60mm from face of cylinder block. If screwdriveer can only be inserted 20mm-turn oil pump sprocket 360". Inset screwdiver again.
Fit balancer shaft delt in anti-clockwise direction starting at crandkshaft sprocket....Slacken balancer shaft belt tensioner notl, turn tensioner clockwise to tension belt. Tighten bolt to 15-22 Nm... Applu thump pressure to belt at tentioner, belt should deflect 5-7mm. If not: Repeat tensioning procedure.... Install - chankshaft sprocket guide washer & crankshaft sprocket.
Thighten crankshaft centre bolt, tightening torque:110-130Nm. Please note, ensure crankshaft sprocket guide washer is fittet correctly. oil threads & contact face crankshaft botl before fitting.

Sep 21, 2009 | Hyundai Elantra Cars & Trucks

1 Answer

Harmonic Balancer needs replaced. How long can I wait until I have to get this done?


its bad the harmonic balancer , balances the crankshaft in relation its a dapener as well as it rotates the timing ..change it soon...

May 07, 2009 | 1999 Pontiac Grand Am GT

1 Answer

87 chevy s10 4x4 vacuum diagram


NOTE<< If Picture Does Not Show Please Email Me @ rejakwilson@aol.com And I Will Send it to You It IS DETAILED And COMPLETE Diagram of Exactly What You Ask For.

Vacuum and Vapor Hose Diagrams Notes Vacuum Actuation System 42242444

Feb 12, 2009 | 1987 Chevrolet S-10 Pickup

1 Answer

Oil light flashing here and there..weird


is it getting noisy... that's usually the first clue... to rule out anything serious have the oil pressure checked.

Robert

Please take a moment to rate this solution thanks

Jan 21, 2009 | 1996 Honda Civic

1 Answer

Vibration at 50km/30mi/hr


It could be the shop has bend the shaft or put a big dent in it or knocked the balance tabs off,causing imbalance. should be the shops expense.

Jun 06, 2008 | 2002 GMC Sierra 1500

2 Answers

2007 honda ridgeline vibration in the steering wheel


that is definitely not normal,i have been a Honda technician for may years and have seen this problem several times.most Honda dealer have a funky new tire balance that does match balancing with road force,have them match balance the tires and do road force,this will take the heavy point of the tire and the light point of the rim,they will index these points and break down the tire and turn the tire to match the light point of the rim,this will also show any non visible bad tire,there is a roller that comes down on the tire as its being balanced and puts approx 9000 pounds of pressure on tire,and measures any excessive internall run out that is not visible,anything above 40lbs of road force after this procedure is not normal,and the tire is no good,most bigger Honda dealer within any major city should have this machine and will know what you are talking about,good luck,Honda should cover that under warranty,especially if it has low kms,don't take no for an answer,go to customer relations

May 18, 2008 | 2006 Honda Ridgeline

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...