Question about Mitsubishi Endeavor

Open Question

I have a miss on cyl#c2 of my endeavor. checked it thoroughly and am convinced it is the coil driver inside the ECM. Can I just install a used computer an get it to work? if no

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: No Start. OBDii Code P2305.

i have the same problem could someone please help ? its getting cold outside and i live 30 miles from my job.

Posted on Oct 27, 2008

Ad
alicantecoli
  • 22246 Answers

SOURCE: GM 2.8 Liter Engine ECM/Coil will produce spark

does a 85 have a ECU unit ??? sounds like it could be the switching transistor thats either under the coil or inside the distributor should look like a black plastic casing with 3/4 wires running to it then to the coil look at this first as often motor runs ,stop for a quickie somewhere and jump back in and engine will not fire up ,classic symptons

Posted on Dec 20, 2008

  • 1348 Answers

SOURCE: 2002 ford ranger 3.0 is missing on 2 cyl plugs ok injectors ok new coilpack

do a compression test,as the intake manifold,like alot of fords is no good.

Posted on May 22, 2009

  • 103 Answers

SOURCE: cyl. 3 miss fire code po303

is it a quad 4 id replace both coils and the module. u can take that ciol plate off the engine ground the plate to the engine with alligator clip wire take an extra set of plug wires ad put them on the coils and the spark plugs start engine pull #3 wire n c if it fires at plug first if not check at the coil still no spark replace that coil. how ever if u have spark but still miss #3 swap injectors 2 and 3 c if u move the miss to #2 if not its prolly mechanical and quad 4s r know for failing

Posted on Mar 18, 2010

johnjnail
  • 1702 Answers

SOURCE: 2006 mercury milan 3.0 motor,no.4 cyl.will burn

did you replace the coil? and if you did was the 1st coil burned the same way? what is the resistance in the coil across the terminals and from secondary out put ( were it plugs on the spark plug ) to each of the plug in terminals. get this info and get back with me and we will see what we can do to get to the bottom of this mystery.

Posted on Apr 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Shift light flashing changed transmission \coil ecm\pcm transmission module diagnostics cyl missfire invalid data u0401


First is year make and model. A U code is data communication codes. Sorry to say, you could have done all this and it could have just been a bad wire.

Mar 19, 2016 | Cars & Trucks

1 Answer

Missing on number 3 cyl


no enough information but here goes
missing can be mechanical ---burnt valve
can be faulty injector or injector control-- injector or ECM wire
HT lead
crack in distributor cap --if not multi coiled
coil if multi coiled
plug as a last resort as most plugs will outlast the engine

Dec 15, 2015 | Cars & Trucks

1 Answer

2004 Sorento began with code P0305, cyl #5 misfire. Inspected and replaced plugs, wires, and coil pack on cyl #2. Repair shop told me cyl #5 injector bad so they replaced. Still has misfire.I suggeste


If you had code P0305, I don't know why they would have done anything to the #2 cylinder but if they have already replaced the plugs, wires and injector; here are a few more items to check:
1) Check connections from ECM. Look for any corrosions or bent/broken pins.
2) Check the fuel line pressure
3) Check the engine compression
4) And if the above are good, then you will probably have a defective ECM

Nov 28, 2014 | Cars & Trucks

1 Answer

94 transport engine miss


Have a compression test done on the engine. Check for burnt valve or bent valve on that cylinder.

Apr 28, 2013 | Cars & Trucks

1 Answer

Wher is the ignition control module located in a jeep grand cherokee lorado


6 or 8 cylinder? Either way the computer (ECM) controls the coils. 6 cyl has a 'coil rail' and 8 cyl had individual coils on each cylinder. There are crankshaft and camshaft sensors that tell the ecm when to fire each cylinder

Dec 12, 2012 | 2000 Jeep Grand Cherokee

1 Answer

1991 cutlass 2.3l DOHC no fire to #1 cyl


Since only cylinder #1 has unburned fuel, then the coil must be working. It could be the cable from the coil to the the # 1 spark plug, or you have burned valves in this cylinder.

Oct 15, 2012 | Cars & Trucks

1 Answer

GM 2.8 Liter Engine ECM/Coil will produce spark


does a 85 have a ECU unit ??? sounds like it could be the switching transistor thats either under the coil or inside the distributor should look like a black plastic casing with 3/4 wires running to it then to the coil look at this first as often motor runs ,stop for a quickie somewhere and jump back in and engine will not fire up ,classic symptons

Dec 20, 2008 | 1985 Jeep Cherokee

1 Answer

No Start. OBDii Code P2305.


i have the same problem could someone please help ? its getting cold outside and i live 30 miles from my job.

Aug 09, 2008 | 2004 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...