Question about 1998 Nissan Frontier

Open Question

1998 nissan frontier hard to get out of park. works sometime whenthe brake feel different

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
pal03246
  • 726 Answers

SOURCE: I have a brake light

do you have a bed liner?? if so, you need to move the bed liner away from the rear lights in back to access the screws that hold the tail light in. on the side of the bed right by the tail light are 2 screws holding the light in. remove screws, remove tail light replace bulbs, re-assemble.

Posted on Jul 24, 2008

Ad

SOURCE: Fuel gauge and engine temperature

We repair this problem. Visit Mr. Whizard Technical Services

Posted on Oct 03, 2008

dealt_soul
  • 296 Answers

SOURCE: 2000 NISSAN FRONTIER VIBRATION

Check tire balance, rear wheel bearings and i would replace u joints front and back, anyway if they have never been repaced.

Posted on Feb 15, 2009

  • 2 Answers

SOURCE: change brake light bulb on a 2000 Nissan Frontier

The entire bed line will need to be removed. The long screws that hold the metal bracet where the bed extender attaches also hold the tail light assembly in place.
I pulled the bed liner up at a 45 degree angle and layed it on top of the cab. This revealed the screws. Take both screws out and lay to the side along with the metal bracket for the bed extender.
Now firmly grab the edges of the tail light assembly and pull...there are 2 hard rubber nipples that snap in to hold the assembly. You will feel like you might break it but you won't..just pull straight back hard. The assembly will "POP" out and then you can just twist the back of each bulb there are (3) and pull out..now you will see the bulbs..just pull the bad bulb straight out and push the new one into place. Now just reassemble. Total time will be 30-45 min. for this repair.

Posted on May 04, 2010

airjer995
  • 5332 Answers

SOURCE: replace the brake light switch

Check the brake fluid level in the master cylinder and make sure the E-brake is not on. The "BRAKE" light does not come on because the brake switch is bad.

Posted on Jun 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the ignition timing for 2002 nissan hardbody 2000i 16v


Here are the 3 engines listed for this year. IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 2.4L SFI 4cyl

The Ignition Timing

18-22 DegreesBefore top dead center - When throttle positionsensor disconnected and using suitably programmedscan tool.When adjusting idle speed, set parking brake & chock drive wheels, curb idle speed (750-850 RPM)transmission in neutral.

IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 3.3L SFI 6cyl

The Ignition Timing

8-12 DegreesBefore top dead center - throttle position sensorharness disconnected.When adjusting idle speed, set parking brake & chock drive wheels, curb idle speed (700-800 RPM)transmission in neutral.

IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 3.3L SFI SC 6cyl

The Ignition Timing

8-12 DegreesBefore top dead center - throttle position sensorharness disconnected.When adjusting idle speed, set parking brake & chockdrive wheels, curb idle speed (700-800 RPM)transmission in neutral.

Jun 05, 2015 | Nissan Hardbody Cars & Trucks

1 Answer

How do i fix my shifter wont come out of park


Set the e-brake before putting in park. If parking on any slope it could be jamming the pawl inside the transmssion.
-

Sep 22, 2014 | 2007 Nissan Frontier SE Crew Cab

1 Answer

Fuel pump relay diagram


The fuel pump relay is located inside the vehicle under the driver's side of the dash just to the left of the parking brake (above it)

Jul 25, 2014 | 1998 Nissan Frontier

1 Answer

Replace brake line switch for a 1998 nissan frontier


The switch is on brake pedal,easy to remove,just unplug electrical connector and remove nut holding on,Here's a link to the part,just look how far the nut is on so you can get it adjusted to where the switch is right when installing new one.

Nov 06, 2013 | 1998 Nissan Frontier

1 Answer

My 1998 Nissan Frontier Brake lights stay on 24/7 jiggle the brake pedal aroumnd lights remain on??


The brake switch is either bad or loose from it's mounting at the pedal.

Aug 25, 2011 | 1998 Nissan Frontier

2 Answers

Park break light stays on sometimes


Check the parking brake light switch which is located under the center module, remove the cover around the parking brake and you'll find it there.

May 21, 2010 | 2003 Nissan Frontier Crew Cab

1 Answer

I am adding trailer lights to my 1998 nissan frontier


You may be better off checking at dealer, or autoparts store for an adapter harness that goes inline. They simply plug into the harness ahead of all your tailights etc, and make it easier. At most, you may end up having to run a separate wire for brake control.

Mar 13, 2009 | 1998 Nissan Frontier

Not finding what you are looking for?
1998 Nissan Frontier Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

78238 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...