I replaced the assembly kit but not change with the auto dump

The piece that is on the glass is glued on with an ultra violet cured adhesive, or a two part epoxy adhesive. The last one I did was cured by the sun in 24 hours (mix, set and cure).

https://www.youtube.com/watch?v=8IBp0Pkoa24

Gluing it back on

https://www.google.com/search?q=fixing+rear+view+mirror+mounting+plate

Permatex® Rear-view Mirror Repair Kit - Canadian Tire

https://www.canadiantire.ca > ... > Interior Car Mirrors
Jan 23, 2022 - Permatex® Rear-view Mirror Repair Kit contains everything required for making professional quality repairs in just minutes Two part adhesive ...
Mount Style: Adhesive
Assembled Weight (kg): 1.00 kg
Assembled Weight (lb): 2.20 lb
Assembled Width (mm): 10.00 mm Rating: 3.3 · ‎$6.49

How to Fix a Rearview Mirror - NAPA Know How Blog

https://knowhow.napaonline.com > how-to-fix-a-rearvi...
Jul 30, 2020 - Most rearview mirror repair kits only come with the glue components, some come with a replacement metal glue-on tab, but you still need a couple ...

Permatex® Rearview Mirror Adhesive Kit

https://www.permatex.com > products > permatex-rearv...
Permatex's Rearview Mirror Adhesive contains everything required for making professional quality repairs in just minutes. This repair kit includes ...

Rearview Mirror Repair Kit - Princess Auto

https://www.princessauto.com > product
Home · Auto Repair · Chemicals, Adhesives and Lubricants · Adhesives and Sealants · Instant Adhesives; Rearview Mirror Repair Kit.

check fuel filter shake and dump out contents to see whats been going threw it, all lines for seepage get pump tester from auto parts store on loan OR Master Fuel Injection Pressure Test Kit

Auto parts stores sell a kit for this problem. Has every thing you need. Once fixed, dump this vehicle. You will be doing it again.

Get refinishing kit from auto parts store ($60-75) and DIY or go to stealorship and they will gladly charge you $200 to refinish. Bulbs are available at most auto ports stores too..

since its a 99 it has a sealed plastic headlamp assembly which means you cannot just replace the lens you have to replace the whole assembly a cheaper option if all that's wrong is they are dull is to polish them and headlight scratch remover/ polish kits are available at any auto parts store just follow the instructions

No, The filter is part of the pump assembly.

Hi:
Your head light assemblies have lenses that are made out of polycarbonate, and they usually can be restored to like new condition with a kit from an auto parts store, and a little elbow grease...All for about $40.

Considering that the light assemblies could cost $200 each

Your code is PO462.  Isuzus made 99-01 with bad fuel level sensors as well as bad fuel pumps located inside your gas tank. You can just replace the sensor but i advice you to replace the whole "fuel pump assembly" to prevent another problem. At a shop this is a costly job they will charge 500$. But if you have faith you can do it your self..it is fairly easy to replace if you have a friend to help even better. but will need to erase the code before or after doing the job to prevent the same symptoms. Buy a "Fuel pump Assembly kit" with and  a gasket (around190$).Remember always  do a job carefully to prevent braking anything.  Raise your car, locate your gas tank unbolt the 4 bolts holding it, disconnect any sensors, there should be 2 other bolts holding the tank once down, you can see the assembly with hoses disconnect too. and pull the assembly out itwill be tight, now  replace with new gasket and assembly kit press down firmly till it locks in. now connect everything the way you took out. Its actually easy...here is a pic of the whole assembly kit.....GOOD LUCK

you have to replace the whole assembly not just the lense. Is the lense broke or just fogged over? if fogged over you can polish them with a kit from the auto parts store.

It would be cheaper to fix the automatic