Question about 2006 Chrysler Town & Country

Open Question

2006 chrysler town and country cooling temperature sensor locating

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
garyq1970
  • 85 Answers

SOURCE: changing fuel filter on 2004 chrysler town and country

  1. Remove or disconnect the following:
    • Negative battery cable
  2. Raise the vehicle and support the fuel tank with a transmission jack.
    • Fuel line from the front of the tank
    • Ground strap
    • Inboard side of the fuel tank straps and front T strap fastener and lower the tank about 6 inches
    • Fuel lines from the fuel pump module
    • Fuel filter
  3. Installation is the reverse of removal. Tighten the fuel filter bolts to 40 inch lbs. (4.5 Nm), the main tank straps to 40 ft. lbs. (54 Nm) and the T strap to 250 inch lbs. (28 Nm).
  4. Start the engine and check for leaks.

Posted on Aug 24, 2008

Ad
polarcycle
  • 1392 Answers

SOURCE: Whirring sound after long drives 2006 Chrysler Town & Country

It is your power steering pump. The solution is to replace the P/S fluid resevoir and fill or flush the system.

Posted on Mar 08, 2009

  • 323 Answers

SOURCE: locassion of output speed sensor on 2003 Town and Country

The input and output speed sensors look identical on the connector side. The one over the solenoid pack is the input, the one closer to the left frame rail or left front wheel is the output sensor. I hope this helps.

Posted on Apr 26, 2009

  • 117 Answers

SOURCE: 2005 crank position sensor location

The crank shaft sensor on that model should be on the driver side towards the back of the tranny its not hard to get to.

Posted on Jun 27, 2009

  • 2926 Answers

SOURCE: need location of crank sensor

You did not mention the engine size you have, but the sensor is mounted on the trans housing and will look like this on a 3.8 liter engine.

53001aa.jpg

Posted on Jul 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I changed thermostat, radiator, water pump, hose, engine cooling temperature sensor, radiator cap and I'm still overheating. 2004 Chrysler town and country


Check the heater cores. There are usually 2 in a T&C. Also check the pipes running to the rear heater core. I recently had to have mine repaired because they were leaking!

May 22, 2015 | 2004 Chrysler Town and Country

1 Answer

Where is ambiant air temp on 2006 town and country3.3


TEMP SENSOR IS LOCATED BEHIND FRONT BUMPER COVER CLOSE TO AC CONDENSOR. CABIN FILTER SHOULD BE UNDER COWL PANEL ON PASSENGER SIDE

Feb 11, 2014 | 2006 Chrysler Town & Country

1 Answer

Where is ambiant air temp on 2006 town and country3.3


Throttle body in front of throttle linkages/cables. IAT- Intake air temperature sensor.

Feb 11, 2014 | 2006 Chrysler Town & Country

1 Answer

A chrysler 2006 T&C is showing 9ASCAP when the car is on and the malfunction light is on.


I would bet you have a temperature sensor problem, have the codes checked in the computer first. This can be done free at most major auto parts stores

Dec 11, 2009 | 2006 Chrysler Town & Country

1 Answer

Describe your 2006 Chrysler Town & Country Problem p0404 engine code


P0404 IS EGR POSITION SENSOR PERFORMANCE..YOU NEED A NEW EGR VALVE..RECOMMEND DISCONNECTING BATTERY WHILE REPLACING EGR VALVE..SOMETIMES CODE WILL NOT GO AWAY EVEN AFTER REPLACING VALVE AND CLEARING CODE WITH SCANNER..VALVE IS LOCATED ABOVE ALTERNATOR ON END OF CYLINDER HEAD..THE BOTTOM BOLT CAN BE TRICKY TO REMOVE AND HAVE HAD TO REMOVE ALTERNATOR TO GET BOLT OUT..YOU WILL NEED A NEW GASKET FOR TUBE AS WELL..ABOUT 120 BUCKS FROM DEALER(CAN)

Jul 25, 2009 | 2006 Chrysler Town & Country

1 Answer

Can't find the temperature sensor on a 3.3L, 2002 LX Town and Country. Is inside the distributor housing?


There can be multiple temperature sensors on a vehicle. I will assume you are looking for the engine temperature sensor. It is normally located on the top of the engine near the front within inches of the top radiator hose. Most only require one wire for operation but some models may have more.

Apr 30, 2009 | 2002 Chrysler Town & Country

1 Answer

2006 town and country overhead console temperature plug in


the ambient temp sensor is mounted in front of a/c condenser..sensor may be broken/missing..should be able to see sensor looking straight in front of lower grille opening..fairly inexpensive and not too bad to replace..dealer part

Apr 17, 2009 | 2006 Chrysler Town & Country

1 Answer

1997 Town & Country outside temperature display shows OC.


check the sensor itself it may have become disconnected, have a broken wire to it or be a bad sensor its located behind the grille

Jan 03, 2009 | 1997 Chrysler Town & Country

Not finding what you are looking for?
2006 Chrysler Town & Country Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...