Question about Cars & Trucks

Open Question

I can not get the pan out. Never used it yet. HELP

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I have a tear in my Trans pan how do I solve please no money for a new one stuck in new jersey on way home please help?

I would try to find a used pan in a salvage yard. The price to have it patched will probably be more than a used pan.

Aug 02, 2011 | Nissan Altima Cars & Trucks

1 Answer

How do I change transmition filter

Start the engine and let it idle for four minutes. This will help to remove as much loose particles from the transmission as possible Turn off the engine. Raise the front of the vehicle using a floor jack, and support the vehicle with two jack stands Apply the emergency brakes and block the rear wheels with two wooden blocks .Place a large drain pan underneath the transmission pan. Loosen the front and side mounting bolts from the transmission pan using a crisscross pattern. Then remove the bolts. Use a ratchet, ratchet extension and socket.Loosen the rear mounting bolts from the transmission pan about 4 turns each. Pry the transmission pan open at the front using a screwdriver and let the oil drain onto the drain pan. Hold the transmission pan from underneath, using a shop rag as you remove the remaining pan mounting bolts. Separate the transmission pan from the transmission, and tilt it over the drain pan to remove the remaining oil. Discard the transmission pan gasket. This is were the filter will be located remove and replace filter and then. Clean the transmission pan with spray carburetor cleaner and a shop rag.Install a new gasket over the transmission pan flange Set the transmission pan in place and start the pan mounting bolts by hand. Start tightening the transmission pan bolts in a crisscross pattern, a little at a time, until all the bolts are tight. Use the ratchet, ratchet extension and socket. Just tighten the bolts enough to create a seal between the pan and the transmission to avoid damaging the pan gasket.

Mar 18, 2011 | 2003 Chevrolet Impala

2 Answers

What transmission is in my 1992 c1500 truck it has the 4.3 engine

some stamp this on the dipstick for the transmission. without seeing the pan on the transmission its either a 700-r4 4L60 or a 4L80 trans. if you count the number of bolts in the trans it would help

Jan 26, 2011 | 1992 Chevrolet C1500

1 Answer

How do I remove oil pan from a ford 2003 3.0 liter?

First lift up the car by using jack stands.Then the oil needs to be drained from the oil pan.There will be nut that has to be removed to drain the oil. Remove the bolts holding the oil pan to the engine block with a ratchet. Use an extension attached to the ratchet to facilitate removal.Also remove the sealant stuck on the engine block area where oil pan was placed.
--------- Refit the replacement oil in the reverse order. ------ this will help.Thanks.Helpmech.

Dec 15, 2010 | 2003 Ford Ranger Regular Cab

1 Answer

I need to know how to remove my oil pan from my 2000 dodge dakota v6 magnum 3.9 lt truck , got the bolts off and the engine mounts removed but oil pan will not come off, plz help. thx

they get stuck on there really good, i have a 2000 durango, and i had tu use a scredriver, and hammer around it, it was so stuck by the time i got it off of there, i had ro replace the pan it was so bent around the lip.... you could use a screwdriver and hammer between the pan and engine, try to barely tap it the screwdriver between them, all the way around the pan.. hope you have better luck than i did..

Dec 03, 2010 | Dodge Dakota Cars & Trucks

3 Answers

I cant find an oil pan for a 96 mercury cougar xr7...i've looked everywhere.please help me.

Visit You can search all over the country for junk yards who sell an oil pan for your cougar (you can also use an oil pan from a thunderbird).

Aug 03, 2010 | 1996 Mercury Cougar XR7

1 Answer

I have a small leak near the oil pan, can you help.

If its coming from a round your oil pan you'll need to rip the engine out pull out the oil pan and replace the seel between the pan and the block make sure you use the right adetives. either that or a bad oil pan plug

Jan 21, 2010 | 2000 Ford Expedition

1 Answer

Need to change the transmission filter

get your self the right tools, the filter, transmission fluid, gasket, gasket silicon, a good wide drain pan, clean rags, some cleaner to clean out the pan like brake parts cleaner. first find the transmission pan. once located undo the bolts around the pans flange or use the drain plug to drain all the fluid. if it doesnt have a drain plug then you have to take off the pan to drain it, messy! once the pan is off you should be able to see the filter and swap it out. clean out the pan, pan magnent, put your new gasket on and use some silicon, bolt it back on. fill the trans back with new fluid. this is straight forward approach. and dont mix the oil pan with the trans pan. the oil pan is under the motor( if that helps) let me know if you need any help or you dont understand something, thanks

Nov 07, 2009 | 1998 Honda Accord

1 Answer

I'm trying to change the oil pan on my 98 accord, I have the new pan but was told there's no gasket for the pan, I have to use a seal gasket, just want to know the process of changing the pan from scratch....

loosen all bolts. the pan should drop if not tap it a little. place the gasket sealant on new pan and then right away put the pan on the block before dries, and tighten all bolts in a scarterred pattern

Mar 04, 2009 | 1998 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides