Question about Dodge Intrepid

1 Answer

How to remove and replace a transmission on a 2001 Intrepid Dodge?

How to remove right drive shaft..?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 14,585 Answers

They pop out. Pry bar does it. Start with a screwdriver if needed. Doing it on the ground is a pain. You may want to remove the axle bracket. And the axle from the wheel bearing.

Posted on Dec 31, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Y my 2001 dodge intrepid won't shift gears


Start with checking you transmission solenoid under the hood. These do go bad often. But also have you serviced the transmission regular this is vital to know. Speed sensors in the trans need to pick up movement also in order to know what to do these are called VSS sensors Vehicle Speed Sensors in these you have input and output. These should be removed and cleaned and tested for resistance to see if it is within range. If you need further help please ask Remember to rate my solution this is how i earn my achievements here on FixYa. Thanks in advance.

Apr 28, 2012 | 2001 Dodge Intrepid

1 Answer

Was driving on the highway in 2002 intrepid and tranny just stopped working goes in drive sometimes but no reverse at all


Sound like the planetery gear sprocket broke. Common problem on some of these Dodge Transmissions. Transmission will have to be removed and rebuild or replaced.

Nov 12, 2010 | 2002 Dodge Intrepid

1 Answer

Replace the Universal Joints, Dodge Intrepid 1997


Cv joints in your intrepid? Remove the tire, unbolt the lower ball-joint, Remove the hub nut, pull outer joint from wheel bearing, pull shaft from transmission.

Apr 22, 2010 | 2004 Dodge Ram 2500

1 Answer

Were is the EGR valve on dodge intrepid 2001


The EGR valve is on the passenger side cylinder head, and it bolts right to the rear part of it. If you remove the upper plenum, its very easy to remove and replace the EGR valve, but it can be done without removing the plenum also.

Hope help with this (remember rated and comment this).

Mar 17, 2010 | 2001 Dodge Intrepid

1 Answer

Axcle shaft 2003 dodge intrepid


remove tire/wheel and remove axle nut!! i thinks its a 32 mm socket and then take the upper strut bolts out of the knuckle theres 2 bolts 18mm if not there 15 mm bolt heads and tilt the knuckle outwards then drive the axle back with a hammer til it clears then take a flat tip bar and pry the axle out of the tranny

Jan 21, 2010 | 2003 Dodge Intrepid

1 Answer

2002 Dodge Intrepid


Chrysler vehicles often need to be driven between 300 - 500 miles for the control module on the transmission to "learn" your driving habits. Avoid punching the gas or driving very slow, and you should be just fine.

Nov 20, 2009 | 2001 Dodge Intrepid

1 Answer

Remove tranny from 2000 Dodge Intrepid what do I have to do?


Its a lot of work. but if your rdy here we go. if u are not doing this on a hoist be prepared for alot of grunting cursing and swearing.
1. raise the vehicle and put it on jack stands high enough so u can work under it safely
2. disconnect the positive battery cable
3. make sure the steering is loose. What i mean by this is: have the key in the ignition in the acc. position. this allows u to turn the wheels with less effort.
4. remove the front tires
5. remove the center caps from the axle hub.
6. next remove the retaining nutz for the axle shafts.
7. remove both outer-tie rod nuts.
8. using a small sledge hammer hit the mounting point of where the tie rods insert into the hub. not the tie rods them selves
9. next with the ties rods out turn the hub assembly outwards towards your self and remove the axle shaft end from the hub.
10. remove the axle shafts.
point of note: on some axle shaft assemblies there is a retaining clip on the shafts them selves. u must make sure this clip comes out with the shaft when u remove it. if it does not and drops in the transmission. u will be taking the trans. apart to get it out.. not fun
11. next remove the transmission to frame connector.
12. there will be 6-9 13mm bolts that connect the transmission to the engine. remove these
13 . do not separate the transmission yet.
14. disconnect the linkages for the shifter that are to the right when u face the transmission.
15 disconnect the sensor assembly from the transmission. its 3-7 wires that plug into the transmission.
16 at this point look around while u are under there to see if there is anything will will hinder the removal of the transmission. exhaust pipes. oil filter starter, transmission lines.
17 next with a prybar , seperate the transmission gently and rock it side to side to aid the removal.
18 remove the transmission from the can not stress this enough. be carefull. heavy parts can fall and break fingers and hurt you. so take your time.
19. with the transmission out remover and replace the torque converter. when replacing a trasmission always change the coverter with it. they can wear out as well and can cause premature failure of the transmission
20. to assemble, reverse the order.
21 when the transmission is in the car. fill the fluids and check for any leaks.
22 start the vehicle and check again for any abnormal sounds, leaks etc. repair as neccessary.



Apr 14, 2009 | 2000 Dodge Intrepid

3 Answers

2001 intrepid cv joint removal and replacement


bearings make growling noises and axles cv joints make a flutter vibration when accelerating or decelerating

Oct 07, 2008 | 2001 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...