Question about 2002 Chevrolet Tracker

Open Question

How to replace cv axle on a 2002 chevy tracker

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
2tone2
  • 7 Answers

SOURCE: what is the procedure to

You don't need the special tools that they use in this procedure, you can use a hammer and a block of wood to get the axle out of the hub and you can use a pry bar to get the axle out of the transmisson.



Notice: Care must be exercised to prevent the constant-velocity joints from being over-extended. When either end of the drive axle is disconnected, over-extension of the joint could result in separation of internal components and possible joint failure. Drive axle joints and seals should be protected any time service is performed on or near the drive axles. Failure to observe this can result in interior joint or seal damage and possible joint failure.
Notice: Prior to removal of drive axle assembly, cover all sharp edges in the area of the drive axle with shop towels so that the seal is not damaged during removal.
Removal Procedure

  1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the tire and the wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  3. Place shop towels underneath the outer joint to protect from any sharp edges.

  4. 141983.gif
    tif.gif
  5. Insert a drift (1) into the caliper and the rotor to prevent the rotor from turning.
  6. Remove the drive axle nut (2) and the washer.
  7. Remove the lower ball join from the steering knuckle. Refer to Lower Control Arm Ball Joint Replacement in Front Suspension. If you remove the right axle, turn the wheel to the left. If you remove the left axle, turn the wheel to the right.
  8. Disconnect the wheel speed speed sensor harness. Refer to Wheel Speed Sensor Replacement in Antilock Brake System.
  9. Disconnect the stabilizer link from the lower control arm. Refer to Stabilizer Shaft Link Replacement in Front Suspension.

  10. 442393.gif
    tif.gif
  11. Use the J 28733-B in order to disengage the axle from the hub and the bearing.
  12. Separate the hub and the bearing assembly from the drive axle. Move the strut and the knuckle assembly rearward.

  13. 500285.gif
    tif.gif
  14. Remove the inner joint from the transaxle using J 33008 attached to J 29794 and J 2619-01 for the intermediate shaft, if equipped.
Installation Procedure Notice: Prior to installation of drive axle assembly, cover all sharp edges in the area of the drive axle with shop towels so that the seal is not damaged during installation.
Any time the front halfshaft is removed, the transmission (the halfshaft male and female shank) and the knuckle sealing surfaces should be inspected for debris or corrosion.
If debris or corrosion are present on the sealing surfaces, clean them with a 320 grit cloth or equivalent. Transmission fluid may be used to clean off any of the remaining debris. The surface should be wiped dry, and the halfshaft should be reinstalled free of any debris or corrosion buildup.

    189013.gif
    tif.gif
  1. Install the drive axle (2) into the transaxle (1). Place a non-ferrous drift into the groove on the joint housing and then tap until the drift is seated. Be careful not to damage the axle seal or dislodge the seal garter spring when you install the axle.

  2. 442471.gif
    tif.gif
    Important: Verify that the drive axle is seated by grasping on the inner joint housing and pulling outboard.
  3. Install the drive axle (1) into the hub and bearing assembly (2).
  4. Install the stabilizer link. Refer to Stabilizer Shaft Link Replacement in Front Suspension.
  5. Connect the wheel speed sensor harness. Refer to Wheel Speed Sensor Replacement in Antilock Brake System.
  6. Install the lower ball joint to the steering knuckle. Refer to Lower Control Arm Ball Joint Replacement in Front Suspension.

  7. 141983.gif
    tif.gif
    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  8. Install the washer and the new drive axle nut (2).
  9. Insert a drift (1) into the caliper and the rotor in order to prevent the rotor from turning.
    Tighten
    Tighten the drive axle nut to 200 N·m (144 lb ft).
  10. Install the tire and the wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  11. Lower the vehicle

Posted on Nov 02, 2008

Ad
emissionwiz
  • 76630 Answers

SOURCE: How to remove CV Axle from Manual Transmission on 2002 cavalier

the axle just pulls or snaps out of the trans, it is held in by an internal round spring clip, they are a real bear to remove the 1st time, u must pull straight out with a sharp jerking motion to get them to release, be patient it will come out.

Posted on Mar 31, 2009

  • 23 Answers

SOURCE: 2002 chevy cavalier drive axle

You may have to have half inch air impact gun to remove the spindle nut (in the center of the rotor). I'd make that the first task to undertake because your next task will be to remove lower ball joint. After you get that spindle nut loose, take a hammer, 32 oz. preferrably and whack area directly behind lower ball joint to coerce it in to loosening up. Then take a decent pry bar and lift up on the whole spindle assembly and if it don't release, go whack the front side in front of lower ball joint. After you get it to come free from lower A arm, take a pry bar and insert it in between the CV joint and transmission housing. Do not put a lot of pressure that will over stress the transmission case, just vigorously enough to get the CV joint to pop out of the circlips that holds it into transmission. Make sure when you put new one in that CV joint reseats all the way and reverse procedure is the same.

Posted on May 11, 2009

  • 76 Answers

SOURCE: how to replace front cv axles in a 1999 chevy

that is a big task and your normal tool box wont have the big socket you need also a heavy duty roll jack if you really want to do this first start with a hanes manul u can get them from autozone even check there web site

Posted on Aug 19, 2009

dherr66170
  • 1 Answer

SOURCE: Replacing my CV Axles

Hi, your axles on the metro are actually called half shafts, any larger name parts house can order them for you. Call them with the Make, Year, and Model and they will take care of you. you will need to tell them,drivers side or passengers side. Hope this helps!

Posted on Aug 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove right side cv axle on 2002 chevy tracker 4x4 2l auto?


Get a Chilton manual from any auto parts store to get a step by step instruction with diagrams.

Sep 09, 2016 | 2002 Chevrolet Tracker

1 Answer

Can you remove the driver side cv axle from a 2005 Chevy asteo van AWD permenanlry


The CV axle stub (end with the axle nut on it) supports the wheel bearing, removing the axle then driving on it would cause the bearing to wear prematurely. I would not recommend this. The front differential is also sealed by the cv assembly, removing it would cause the diff fluid to leak out . CV shafts for this van run $50-80. I would replace if it is bad, instead.

May 04, 2014 | 2002 Chevrolet Astro

1 Answer

Replace cv boot on a chevy tracker


If your question is about repairing a torn axle boot, it is more common to replace axle

Feb 01, 2014 | 2000 Chevrolet Tracker

1 Answer

Front end wheel noise when turning


Check the front axle boots for crack.
A crack CV boot will lose the grease.

Only way is to replace the CV axle.

Jan 13, 2014 | Chevrolet Cars & Trucks

1 Answer

Chevy tracker 4wd


check your cv joints

Sep 28, 2013 | 1999 Chevrolet Tracker

1 Answer

Replaced both CV axles on1999 chev tracker. Bought at autozone.they lasted 200 miles and shot.neccessary to buy O.E.M.?


changed a bunch of cv axle thats the quikest ive ever herd of going out oem neccessary wouldnt think so try a second set or go to different parts house

Dec 15, 2010 | 1999 Chevrolet Tracker

1 Answer

1993 geo tracker , the front cv joint axles need new boot and bearing. Is it easy for a back yard mechanic?


ITS NOT A HARD JOB TO DO BUT YOU NEED TOOLS LIKE TIE ROD END REMOVING TOOL,YOU NEED SHAP RING PLIERS,YOU NEED HYDRALIC JACK AND AXLE NUT SOCKET 1/2 BREAKER BAR AND A TORQUE WRENCH RANGES TO 200 FT LBS YOU WILL NEED REPAIR MANUAL FOR TORQUE SPECS.THE ,MANUAL WILL SHOW AND TELL YOU HOW TO REMOVE FRONT AXLE SHAFT CV JOINTS.IT WILL LOT CHEAPER TO BUY WHOLE FRONT AXLE WITH NEW CV JOINTS.YOU NEED CV JOINT BOOT CLAMP TOOL AND ITS A WHOLE LOT OF CLEANING INVOLVE PLUS PACKING NEW BEARINGS WITH GREASE.ITS MORE OF HEAD ACHE BEST TO BUY NEW ONE.

Aug 28, 2010 | 1993 Geo Tracker

1 Answer

How to remove and replace a passanger front axle for an 02 chevy tracker?


THIS AXEL IS THE SHORT ONE,ABS SYSTEM,START OUT REMOVING THE CALIPER AND PADS,ALL BOLTS ARE METRIC,REMOVE THE AXLE BOLT FIRST,THEN,REMOVE THE TIE ROD BOLT,THEN REMOVE THE UPPER CONTROL ARM BOLT,THE SPINDLE WILL LEAN FORWARD TO GIVE YOU ROOM TO REMOVE THE OUTER PART OF THE AXLE,THEN BE CAREFUL,BUT USING THE RIGGT PRY TOOL,REMOVE TE AXLE

Apr 04, 2010 | 2002 Chevrolet Tracker

1 Answer

I replaced the right front cv axle on my 2000 Chevy Tracker with a new axle. The axle keeps pulling away from the wheel hub pushing the snap ring on the outer portion of the shaft out of its groove. I've...


reason u replaced the cv the first time ?? problem could be the hub has play or trans/engine mount went bad causing the motor and trans unit to flex under acceleration and braking-- check ur axle lengths by measuring old original to the new ones before swapping out again

Nov 26, 2009 | 2000 Chevrolet Tracker

1 Answer

How to remove CV Axle from Manual Transmission on 2002 cavalier


the axle just pulls or snaps out of the trans, it is held in by an internal round spring clip, they are a real bear to remove the 1st time, u must pull straight out with a sharp jerking motion to get them to release, be patient it will come out.

Mar 31, 2009 | 2002 Chevrolet Cavalier Coupe

Not finding what you are looking for?
2002 Chevrolet Tracker Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...